Panasonic DMR-EZ48V Operating Instructions Manual page 59

∫ Settings for Digital Services
Press [OK] to show the following settings.
DVB Manual Tuning
You can set channels manually that the DVB Auto-Setup could not
complete successfully.
1 Press [3, 4] to select "DVB Manual Tuning" and press [OK].
DVB Manual Tuning
Channel System
Australia
Frequency DVB CH24 498,0
Signal Quality 0
Signal Strength 0
Prog. Channel Service Name Net ID TS ID Quality
START SCAN
OFFSET
RETURN
CHANNEL
2 Press [3, 4] to select the channel you want to set.
3 Press [2, 1] to adjust the frequency.
≥The frequency rises and falls in steps of 0.5 MHz.
≥Adjust the frequency by checking the signal strength and signal
quality displays.
[Refer to "Signal Condition" (➡below) for signal quality and
signal strength.]
4 Press [OK] to start scan.
The set channel is displayed in the table.
5 Press [EXIT] and press [W X CH] to check that applicable
channels have been selected.
Add New DVB Services
You can search for newly added terrestrial digital channels to
receive.
1 Press [3, 4] to select "Add New DVB Services" and press [OK].
The unit starts searching for newly available terrestrial digital
channels. This takes about 5 minutes.
Add New DVB Services
Please wait! Ch 6
Prog. Channel Service Name Net ID TS ID Quality
RETURN: to cancel
RETURN
A message is displayed when the search is finished.
"No new services found." is displayed when no new services can
be found.
2 Press [OK] to save the newly found channels.
Signal Condition
You can check the quality and strength of digital broadcast signals.
Realign the aerial if you are receiving a poor signal.
When "Signal Condition" is displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [W X CH] to select a digital channel. "D" appears on the
unit's display.
3 Display the Setup menu again (➡ 58).
Press [3, 4] to select "Signal Condition" and press [OK].
The quality and strength of the signal are shown.
Press [W X CH] to select the channel.
Signal Quality 0 10
Signal Strength 0 10
CH +
CH –
RETURN
Signal Quality
Below 2 (display red): The signal quality is so poor that there may
be interference in the pictures and sound.
2–5 (display orange): The signal quality is basically adequate, but
brief interference in the pictures and sound
is possible in isolated case.
Over 5 (display green): Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. "0" means signal strength 0%,
"10" means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.
≥When the signal is weak:
– adjust the position and direction of the aerial.
– adjust the aerial reception with "DVB Manual Tuning" in the
Setup menu (➡ above).
– check that the current digital broadcast channel is correctly
broadcasting.
MHz
10
10
69
∫ Settings for Analogue Services
Press [OK] to show the following setting.
Manual Tuning
You can delete analogue channels and set the analogue channel
details.
Press [OK] to show Manual Tuning screen.
Manual Tuning
Pos Name Ch Pos Name Ch
1 ARD 4 11
2 ZDF 2 12
3 N3 5 13
4 HR3 8 14
5 BR3 10 15
6 16
7 17
SELECT
8 18
OK
9 19
RETURN
10 20
Delete
To delete a programme position
Press [3, 4, 2, 1] to select a programme position and press the
"Red" button.
To change the tuning settings for individual programme
position
1 Press [3, 4, 2, 1] to select a programme position and press
[OK].
Pos 1
Manual
Name ARD
Tuning
Channel 4
Fine Tuning Auto
Mono Off
SELECT
RETURN
RETURN : leave
2 Press [3, 4] to select an item and press [1].
Pos Programme position in the table
(You cannot change the programme position.)
Name To enter or change the name of a TV
station
Press [3, 4, 2, 1] to enter station name
and press [OK].
If the station name needs a blank space,
select the blank between "Z" and "¢".
Channel To enter newly available TV stations or
change the channel number of an already
tuned TV station
Press [3, 4] or the numbered buttons to
enter the channel number of the desired TV
station.
Wait a few moments until the desired TV
station has been tuned.
After the desired TV station is tuned, press
[OK].
Fine Tuning To obtain the best tuning condition
Press [3, 4] to adjust the best tuning
condition and press [OK].
≥Press [1] to return to "Auto".
Mono To select the type of sound to be recorded
Press [3, 4] to select "On" if the stereo
sound is distorted due to inferior reception
conditions, or if you want to record the normal
(mono) sound during a stereo, bilingual
broadcast, and press [OK].
RQT9127
59