Copying - Panasonic DMR-EZ48V Operating Instructions Manual

Copying

EJECT
AV2 IN IN 2 S VIDEO VIDEO S VIDEO VIDEO L L /MONO AUDIO R /MONO AUDIO R
DRIVE
SELECT

AUDIO
 REC
One Touch copying (VHS l DVD)
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW]
You can copy programmes recorded on a video cassette onto a disc
with one stroke of the button.
In One Touch Copying, programmes are automatically copied onto
the disc from the location of playback at the time when the copying of
the tape starts.
Preparation
≥Turn on the television and select the appropriate video input to
suit the connection to this unit.
≥When copying an NTSC tape to a DVD, change the "TV
System" to "NTSC" in the Setup menu (➡ 62). This unit cannot
record NTSC signals to discs that already have PAL signal
recordings.
VHS (Recording source)
≥Press [DRIVE SELECT] to select the VHS drive.
≥Insert the video cassette containing the programme to be
copied. (➡ 14)
≥Press [1] (PLAY) to play the video cassette and then press
[AUDIO] to select the audio type you wish to record.
≥Stop the tape at the position where you wish to start recording.
DVD (Recording target)
≥Press [DRIVE SELECT] to select the DVD drive.
≥[RAM] Release protection. (➡ 55)
≥Insert a disc and confirm there is sufficient empty space for
recording on it. (➡ 14, 54)
≥Select the recording mode. (➡ 24)
RQT9127
20
DRIVE SELECT
OPEN/CLOSE
CH CH
DRIVE SELECT REC
¥ REC ∫ 1
COPYING indicator
DVD/VH S
TV


V O L
CH
DRIVE
SELECT
A V
TRACKING/ V-LOCK/ V V PA P P G E
3
1 2
CH
4 5 6
ANALOGUE
7 8 9
CH
G-Code
DELETE
0 INPUT
SELECT
RESET
SL O W/SEARC H
SKIP/ INDEX REW FF
P A US E PLA Y A A
S T O P 
S TA TU S EXIT
OK
OPTION
RETURN
RETURN
CRE A T E
A UDI O DISPL A Y MAN U AL SKI P
CHAPTER
REC REC MODE TIME SLIP PROG/CHECK
JET REW
1
While both DVD and VHS are stopped
" DVD
Press and hold [" DVD, COPYING] on
the main unit for about 3 seconds or
more (until "START" on the unit's
display stops flashing).
COPYING COPYING
≥Check if copying starts properly.
≥Copying is automatically stopped when the tape reaches its
end or the disc becomes full.
[-R] [-R]DL] [-RW‹V›] [+R] [+R]DL]
When the screen on
the right appears
before recording
starts, press [¥ REC]
or [1] (PLAY) to copy
the disc with or
without finalising.
≥If you press [¥ REC], the disc will automatically be finalised
after copying completes.
After finalising, the discs become play-only and you can play
them on other DVD equipment.
However, you can no longer record or edit.
≥If you press [1] (PLAY), you can start copying without
finalising.
≥If you press [∫], you can cancel the copy.
≥Finalising will not start if copying is not completed (e.g.,
due to shortage of remaining disc space).
∫ To stop copying in the middle
Press [∫] or press and hold [RETURN] for about 3 seconds or more.
≥However you cannot stop finalise after it has started.
[Note]
≥While One Touch Copying is activated, a timer recording cannot be
started.
≥When the copying is not started or not executed, the "COPYING"
indicator blinks for about 7 seconds. Check if the unit is properly
prepared.
∫ Dividing a title to be copied
When copying from VHS to DVD, the title is divided by index
signal (➡ 35) detected and then recorded. You can search
desired titles with the Direct Navigator (➡ 33) after copy to DVD.
≥Titles that are too short may not be divided correctly.
≥The recording time may become longer than the original title
depending on the number of index signals.
If you want to copy without dividing the contents into titles,
follow the method below.
≥Set "Time Setting" to "On" on the GUI Copy (➡ 48).
e.g.; [RAM]
COPY
Copy
Do you want to finalise the disc
after copying completes?
Finalising is to allow the disc to be played on
other DVD players. The disc becomes play-only.
Press REC to start finalising after
copying completes.
Press PLAY to start copying only.
Press STOP to cancel copying.