DAELIM S2 125 Service Manual page 15

SERVICE INFORMATION
TORQUE VALUES
ENGINE
ITEM
OIL FILTER CAP
OIL DRAIN PLUG BOLT
VALVE ADJUST SCREW LOCK NUT
CYLINDER HEAD BOLT
FLYWHEEL BOLT
DRIVE FACE NUT
CLUTCH OUTER BOLT
CAM CHAIN TENSIONER PIVOT BOLT
SPARK PLUG
DRIVE PLATE
CAM SHAFT HOLDER NUT
CAM CHAIN TENSIONER FLANGE BOLT
CAM CHAIN TENSIONER PAN SCREW
CYLINDER HEAD COVER BOLT
MISSION COVER BOLT
MISSION COVER DRAIN BOLT
MISSION COVER CHECK BOLT
COOLING FAN BOLT
STARTING CLUTCH NUT
STARTER MOTOR FLANGE BOLT
RADIATOR OIL BOLT
OIL PUMP FLAT SCREW
OIL PUMP DRIVEN GEAR NUT
FRAME
ITEM
STEERING STEM NUT
STEERING TOP THREAD NUT
FORK PIPE BOTTOM BRIDGE
HANDLE POST
FRONT AXLE NUT
FRONT CALIPER BRACKET BOLT
FRONT MASTER CYLINDER HOLDER BOLT
FRIBT DISK PLATE BOLT
REAR AXLE NUT
REAR CALIPER BRACKET BOLT
REAR MASTER CYLINDER HOLDER BOLT
REAR DISK PLATE BOLT
SPEEDOMETER GEARBOX SCREW
FRONT FORK BOLT
REAR CUSHION UPPER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION LOCK NUT
ENGINE HANGER UPPER BOLT
ENGINE HANGER LOWER BOLT
MAINSTAND BOLT
SIDESTAND PIVET SEREW
SIDESTAND PIVET NUT
Torque values listed above are for specific tightening points. Torque values for other items are listed in the following table.
1-12
THREAD DIA
Q'TY
(mm)
1 20
1 12
4 5
2 6
1 12
1 12
1 12
1 8
1 12
1 30
4 8
2 6
1 6
4 6
8 6
1 8
1 8
3 6
1 22
2 6
4 12
3 6
1 6
THREAD DIA
Q'TY
(mm)
1 26
1 26
1 10
2 10
1 12
2 8
2 6
3 8
1 16
2 8
2 6
3 8
1 5
2 22
2 10
2 10
2 10
2 12
1 10
2 10
1 10
1 10
TORQUE VALUE REFERENCE
1.1 kgf·m
2.5 kgf·m
0.8 kgf·m
1.0 kgf·m
5.5 kgf·m
7.5 kgf·m
5.5 kgf·m
1.0 kgf·m
1.2 kgf·m
5.5 kgf·m
Apply engine oil
2.0 kgf·m
1.0 kgf·m
0.4 kgf·m
0.9 kgf·m
1.2 kgf·m
1.0 kgf·m
0.9 kgf·m
1.0 kgf·m
9.5 kgf·m
0.9 kgf·m
3.2 kgf·m
1.0 kgf·m
1.0 kgf·m
TORQUE VALUE REFERENCE
7.0 kgf·m
0.25 kgf·m
7.5 kgf·m
6.0 kgf·m
6.0 kgf·m
3.1 kgf·m
1.2 kgf·m
4.25 kgf·m
12.5 kgf·m
3.1 kgf·m
1.2 kgf·m
4.25 kgf·m
0.43 kgf·m
2.25 kgf·m
4.0 kgf·m
4.0 kgf·m
3.5 kgf·m
5.25 kgf·m
4.5 kgf·m
4.0 kgf·m
1.5 kgf·m
4.5 kgf·m
Initial torque