Receiving; Tuning Steps; Of The [ Main Dial ] Knob; Of The [ Dsp/Sel ] Knob - Yaesu FT-450D Operation Manual

The tuning step of the [ MAIN DIAL ] knob and the
[ DSP/SEL ] knob is different depending on the oper-
ating mode.
O
PERATING
M
MAIN DIAL
ODE
LSB/USB 1/10/20 Hz 1.0/2.5/5.0 kHz
CW 1/10/20 Hz 1.0/2.5/5.0 kHz
2
AM 100/200 Hz 2.5/5.0/9.0/10/12.5/25 kHz
2
FM 100/200 Hz 5.0/6.25/10/12.5/15/20/25/50 kHz
DATA 1/10/20 Hz 1.0/2.5/5.0 kHz
1: When you press the [ DSP/SEL ] knob, the tuning step of the
[ DSP/SEL ] knob changes to 100 kHz in all modes.
2: In the factory default, the [ MAIN DIAL ] knob does not tune
the AM and FM modes. However, you may activate the [ MAIN
DIAL ] knob on the AM and FM mode via Menu Item
"A&FDIAL".
Pressing the [ FAST ] button will increase or de-
crease the tuning rate of the [ MAIN DIAL ] knob
by a factor of ten and also increase or decrease
the tuning rate of the [ DSP/SEL ] knob by a factor
of two.
C T S
HANGE THE UNING
1. Set the operating mode by pressing the
[ MODE ] / [ MODE ] button.
2. Press and hold the [ F ] button for one second to
enter the Menu mode. The "
pear on the display.
3. Rotate the [ DSP/SEL ] knob to select the menu
item "DIALSTP".
4. Press the [ DSP/SEL ] knob to enable adjustment
of this menu item. The "
ing.
5. Rotate the [ DSP/SEL ] knob to select the desired
tuning step described above.
(You may Press the [ RCL/HOME ] button to reset
the tuning step to the factory default.)
6. Press the [ DSP/SEL ] knob. The "
displayed continuously.
7. Press and hold the [ F ] button for one second to save
the new setting and return to normal operation.
C T S
HANGE THE UNING
1. Set the operating mode by pressing the
[ MODE ] / [ MODE ] button.
2. Press the [ F ] button momentarily.
3. Press the [ SPLIT/STEP ] button.
4. Rotate the [ DSP/SEL ] knob to select the desired
tuning step described above.
5. Press the [ DSP/SEL ] knob to save the new set-
ting and return to normal operation.
FT-450D O
PERATION
T
UNING
K
NOB
1
DSP/SEL
MAIN DIAL K
TEP OF THE
" icon will ap-
" icon will be blink-
" icon is
DSP/SEL K
TEP OF THE
M
ANUAL
S
TEPS
[ DSP/SEL ] knob
Regarding of the [ DSP/SEL ] knob
The [ DSP/SEL ] knob is used for operating
various functions depending on the situation.
If you can not change the frequency/memory
channel by tuning the [ DSP/SEL ] knob, the
[ DSP/SEL ] knob is selected to operate of one
of the DSP functions.
In this case, press the [ DSP ] button several
times until the ">" icon disappears from the
DSP Graphic Display.
NOB
[ DSP/SEL ] button
[ MODE ] / [ MODE ] button
NOB
[ DSP/SEL ] knob
[ MODE ] / [ MODE ] button
R
ECEIVING
[ FAST ] button
[ MAIN DIAL ] knob
N
OTICE
[ RCL/HOME ] button
[ F ] button
[ SPLIT/STEP ] button
[ F ] button
Page 19