Yaesu FT-450D Reference Book
Computer aided transceiver
Hide thumbs
Also See for FT-450D:
- Operation manual (104 pages) ,
- Technical supplement (98 pages) ,
- Manual (3 pages)
Related Manuals for Yaesu FT-450D
Summary of Contents for Yaesu FT-450D
- Page 1 PERATION OMPUTER IDED RANSCEIVER FT-450D CAT O PERATION EFERENCE YAESU MUSEN CO., LTD. FT-450D CAT O PERATION EFERENCE...
- Page 2 UNCTION The FT-450D has a built-in level converter, allowing di- SERIAL OUT Output Outputs the Serial Data from the rect connection from the rear-panel CAT jack to the serial transceiver to the computer.
- Page 3 Terminator mand List” and the “Control Command Tables” to con- figure the appropriate parameters. There is three for the FT-450D Command as shown below: When configuring parameters, be careful not to make the Set command: Set a particular condition following mistakes.
-
Page 4: Command List
LOAD MESSEGE MIC UP MEMORY CHANNEL VOX DELAY TIME MODE VOX GAIN [ V/M ] KEY FUNCTION MIC GAIN MODE KEY VOICE MONITOR LEVEL VFO SELECT MEMORY READ VFO TO VFO METER SW Page 3 FT-450D CAT O PERATION EFERENCE... - Page 5 11: GEN B B B B B U U U U U BAND UP P1 0: Fixed Read Answer BUSY P1 0: BUSY “OFF” 1: BUSY “ON” P2 0: Fixed Read Answer P1 P2 FT-450D CAT O Page 4 PERATION EFERENCE...
- Page 6 177.3 Hz 206.5 Hz 82.5 Hz 110.9 Hz 151.4 Hz 179.9 Hz 210.7 Hz 85.4 Hz 114.8 Hz 156.7 Hz 183.5 Hz 218.1 Hz 88.5 Hz 118.8 Hz 159.8 Hz 186.2 Hz 225.7 Hz Page 5 FT-450D CAT O PERATION EFERENCE...
-
Page 7: Control Command
PERATION OMPUTER IDED RANSCEIVER ONTROL OMMAND ABLES ENCODER DOWN P1 0:Fixed P2 01-99: Steps P1 P2 P2 Read Answer ENCODER UP P1 0:Fixed P2 01-99: Steps P1 P2 P2 Read Answer FT-450D CAT O Page 6 PERATION EFERENCE... - Page 8 00 (OFF) ~ 01 (minute) ~ 20 (minute) TUNER/ATAS 0: ATAS 1: EXT ATU 2: INT ATU 3: INTRATU 4: F TRANS VOX DELAY 01 (100 msec) ~ 30 (300 msec) VOXGAIN 001 ~ 255 Page 7 FT-450D CAT O PERATION EFERENCE...
-
Page 9: Command Tables
177.3 Hz 206.5 Hz 82.5 Hz 110.9 Hz 151.4 Hz 179.9 Hz 210.7 Hz 85.4 Hz 114.8 Hz 156.7 Hz 183.5 Hz 218.1 Hz 88.5 Hz 118.8 Hz 159.8 Hz 186.2 Hz 225.7 Hz FT-450D CAT O Page 8 PERATION EFERENCE... - Page 10 P2 P2 P2 P3 P3 P3 P3 P3 P4 P5 P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC P9 Tone Number (See Table 1) P10 0: Simplex 1: Plus Shift 2: Minus Shift P6 P7 P8 P9 P9 P10 Page 9 FT-450D CAT O PERATION EFERENCE...
- Page 11 P1 001 - 504: Memory Channel Number 001 - 500: Regular Memory Channel P1 P1 P1 501: P1L Channel Read 502: P1U Channel 503: P2L Channel Answer 504: P2U Channel P1 P1 P1 FT-450D CAT O Page 10 PERATION EFERENCE...
- Page 12 P10 0: Simplex 1: Plus Shift 2: Minus Shift N N N N N A A A A A NARROW P1 0: Fixed P2 0: Bandwidth Middeum P1 P2 1: Bandwidth Narrow Read Answer P1 P2 Page 11 FT-450D CAT O PERATION EFERENCE...
- Page 13 When the power supply becomes “ON", the dummy data is sent. The command that makes the power supply “ON" within two seconds after wait is done for about one second is sent. Answer FT-450D CAT O Page 12 PERATION EFERENCE...
- Page 14 1: MIC-EQ 3: REC Read 4: PLAY P2 0: OFF Answer 1: ON P1 P2 NOISE REDUCTION LEVEL P1 0: Fixed P2 01 - 11 P1 P2 P2 Read Answer P1 P2 P2 Page 13 FT-450D CAT O PERATION EFERENCE...
-
Page 15: Radio Status
11 - 21 (Normal) Read 22 - 31 (Wide) P3 00 (Narrow) Answer 16 (Normal) 31 (Wide) P1 P3 P3 S-METER READING P1 0: Fixed P2 000 - 255 Read Answer P1 P2 P2 P2 FT-450D CAT O Page 14 PERATION EFERENCE... - Page 16 P1 P1 P1 P1 Read Answer P1 P1 P1 P1 V V V V V G G G G G VOX GAIN P1 000 - 255 P1 P1 P1 Read Answer P1 P1 P1 Page 15 FT-450D CAT O PERATION EFERENCE...
- Page 17 VFO SELECT P1 0: VFO-A 1: VFO-B Read Answer VFO TO VFO Copy the displayed VFO data to the opposite VFO. Read Answer VOX STATUS P1 0: VOX “OFF” 1: VOX “ON” Read Answer FT-450D CAT O Page 16 PERATION EFERENCE...
- Page 18 PERATION OMPUTER IDED RANSCEIVER Copyright 2017 YAESU MUSEN CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of 1710-B YAESU MUSEN CO., LTD. FT-450D CAT O PERATION EFERENCE...