Fuel Safety; Special Notice - McCulloch MAC 250 B Instruction Manual

S Install required shield properly before using
the unit.
S Use only specified blade or trimmer head;
make sure it is properly installed and se-
curely fastened.
S Never start engine with clutch shroud re-
moved. The clutch can fly off and cause se-
rious injury.
S Be sure blade or trimmer head stops turning
when engine idles.
S Make carburetor adjustments with the low-
er end supported to prevent blade or trim-
mer line from contacting any object. Hold
unit by hand; do not use the shoulder har-
ness for support.
S Keep others away when making carbure-
tor adjustments.
S Use only recommended McCulloch accesso-
ries and replacement parts.
S Have all maintenance and service not ex-
plained in this manual performed by your au-
thorised service dealer.

FUEL SAFETY

S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the unit.
S Avoid spilling fuel or oil. Wipe up all fuel spills.
S Move at least 3 meters away from fueling
site before starting engine.
S Stop engine and allow to cool before re-
moving fuel cap.
S Always store petrol in a container approved
for flammable liquids.
CUTTING SAFETY
WARNING:
Inspect the area to be cut
before each use. Remove objects (rocks,
broken glass, nails, wire, string, etc.) which
can be thrown or become entangled in the
blade or trimmer head.
S Keep others including children, animals,
bystanders, and helpers at least 50 feet (15
meters) away. Stop engine immediately if
you are approached.
S Always keep engine on the right- -hand side
of your body.
CARTON CONTENTS
Check carton contents against the following list:
S Brushcutter
S Blade
S Cupped washer
S Large nut for installing blade
S Trimmer head
S Combination shield
S Bolt
S Handlebar
S Handlebar bracket cover
S Handlebar bracket cover screws (2)
S Upper shoulder harness clamp
S Lower shoulder harness clamp
S Shoulder harness clamp screws (2)
S Hold the unit firmly with both hands.
S Keep firm footing and balance. Do not
overreach.
S Keep blade or trimmer head below waist
level. Do not raise engine above your waist.
S Keep all parts of your body away from blade,
trimmer head, and muffler when engine is
running. A hot muffler can cause serious
burns.
S Cut from your left to your right. Cutting on
right side of the shield will throw debris
away from the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow the engine to cool; secure unit before
storing or transporting in vehicle.
S Empty fuel tank before storing or transporting
the unit. Use up fuel left in the carburetor by
starting engine and letting it run until it stops.
S Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Store unit so line limiter cannot accidentally
cause injury. Unit can be hung by the shaft.
S Always install transport guard on blade be-
fore transporting or strorage.
S Store the unit out of the reach of children.
S Secure the machine during transport.

SPECIAL NOTICE:

through prolonged use of petrol powered hand
tools could cause blood vessel or nerve dam-
age in the fingers, hands, and joints of people
prone to circulation disorders or abnormal swell-
ings. Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in skin
color or texture, or loss of feeling in the fingers,
hands, or joints, discontinue the use of this tool
and seek medical attention. An anti-vibration
system does not guarantee the avoidance of
these problems. Users who operate power tools
on a continual and regular basis must monitor
closely their physical condition and the condition
of this tool.
ASSEMBLY
S Shoulder harness
S Hex wrench
S Wrench
S Transport guard
S Throttle cable clip
WARNING:
connect spark plug before performing any as-
sembly procedures.
WARNING:
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
5
Exposure to vibrations
Always stop unit and dis-
If received assembled,