1. Manuals
  2. Brands
  3. McCulloch Manuals
  4. Brush Cutter
  5. 2500CXL
  6. Instruction manual

McCulloch 2500CXL Instruction Manual

Hide thumbs Also See for 2500CXL:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
2500CXL
INSTRUCTION MANUAL
IMPORTANT INFORMATION
: Please read these instructions carefully and make
GB
sure you understand them before using this unit. Retain these instructions for future
reference.
MANUEL D'INSTRUCTIONS
RENSEIGNEMENTS IMPORTANTS:
Avant d'utiliser cet appareil, veuillez lire
FR
atentivement les instructions et assurez- -vous de les avoir comprises. Conservez
les instructions pour référence ultérieure.
BETRIEBSANWEISUNG
WICHTIGE INFORMATION:
Lesen Sie diese Hinweise zur Handhabung des
DE
Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie
alle Anweisungen verstanden haben und gut aufbewahren.
MANUAL DE INSTRUCCIONES
INFORMACIÓN IMPORTANTE:
ES
Lea atentamente las instrucciones y
asegúrese de entenderlas antes de utilizar esta aparato. Conserve las instruc-
ciones para la referencia en el futuro.
545140969
12/15/06

Advertisement

Table of Contents
loading

Related Manuals for McCulloch 2500CXL

Summary of Contents for McCulloch 2500CXL

  • Page 1 2500CXL INSTRUCTION MANUAL IMPORTANT INFORMATION : Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. MANUEL D’INSTRUCTIONS RENSEIGNEMENTS IMPORTANTS: Avant d’utiliser cet appareil, veuillez lire atentivement les instructions et assurez- -vous de les avoir comprises. Conservez les instructions pour référence ultérieure.

  • Page 2: Identification Of Symbols

    IDENTIFICATION (WHAT IS WHAT?) 1. Fuel tank 12. Throttle trigger 2. Handlebar 13. Throttle lock- -out 3. ON/STOP switch 14. Starter handle 4. Shoulder strap clamp 15. Fuel cap 5. Shoulder strap 16. Primer bulb 6. Trimmer head 17. Start lever 7.

  • Page 3: Safety Rules

    WARNING! This brushcutter can be dangerous! Careless or improper use can cause serious or even fatal injury. B. Read and understand the instruction manual before using the brushcutter. C. Always use: Ear protection, eye protection, head protection, boots, and gloves. DANGER! Blade can thrust violently away from material it does not cut.

  • Page 4: Operator Safety

    S Use only 3 mm diameter McCulloch brand WARNING: replacement line. Never use wire, rope, The blade continues to string, etc. spin after the throttle is released or, engine is S Install required shield properly before using turned off. The coasting blade can throw objects the unit.

  • Page 5: Special Notice

    TRANSPORTING AND STORAGE SPECIAL NOTICE: Exposure to vibra- S Allow the engine to cool; secure unit before tions through prolonged use of gasoline pow- storing or transporting in vehicle. ered hand tools could cause blood vessel or S Empty fuel tank before storing or transport- nerve damage in the fingers, hands, and ing the unit.

  • Page 6: Attaching The Handlebar

    NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the Secondary Hole shoulder. 2. Adjust the strap, allowing the hook to be about 15 cm below the waist. 3. Fasten the strap hook to the clamp located between the trigger handle and the handle- bar clamp base and lift the tool to the operat- ing position.
  • Page 7 3. Pivot shield until bolt passes through hole in bracket. 4. Reinstall nut and tighten securely with wrench (provided). NOTE: If your unit has a plastic cover over the threads on the threaded shaft, remove the covering to expose the threads. Before instal- 76 cm ling the trimmer head, make sure the dust cup and retaining washer are positioned on the...
  • Page 8 These 10. Remove the screwdriver. parts must be provided by McCulloch and 11. Turn blade by hand. If the blade binds installed as shown below. Failure to use proper against the shield, or appears to be uneven,...

  • Page 9: Operation

    Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled en- Primer Bulb gine oil. We recommend McCulloch brand oil mixed at a ratio of 40:1 (2.5%). A 40:1 ratio is obtained by mixing 5 liters of unleaded gasoline with 0,125 liter of oil.

  • Page 10: Starting A Flooded Engine

    STARTING A FLOODED ENGINE Primary Hole Coupler Flooded engines can be started by placing Guide Recess the ON/STOP switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter handle repeatedly while squeezing throttle trigger until engine starts and runs.

  • Page 11: Cutting Methods

    OPERATING INSTRUCTIONS FOR Trimming USE WITH TRIMMER HEAD WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury. Before trimming, bring engine to a speed suffi- cient to cut material to be trimmed.

  • Page 12: Additional Safety Rules

    OPERATING INSTRUCTIONS FOR S Cut only from your left to your right. Cutting on right side of the shield will throw debris away USE WITH WEED BLADE from the operator. S Blade Thrust is a reaction that only occurs S Use the shoulder strap and keep a firm grip when using a bladed unit.

  • Page 13: Edger Safety

    EDGER SAFETY S Never use for spreading chemicals, fertilizers, or other substances which may contain toxic WARNING: materials. Inspect the area to be S To avoid spreading fire, do not use near leaf or edged before each use. Remove objects brush fires, fireplaces, barbecue pits,...
  • Page 14 WARNING: WARNING: Inspect the area before Keep the pruner away starting the unit. Remove all debris and hard from power lines or electrical wires. objects such as rocks, glass, wire, etc. that S Only use for pruning limbs or branches up to can ricochet, be thrown, or otherwise cause 10 cm in diameter.

  • Page 15: Maintenance

    1. Remove and discard worn line before installing new line. For unit to operate properly, the cutting line 2. Use only 3 mm diameter McCulloch brand should be replaced when line becomes worn to cut length line. less than 8 cm in length from the edge of the line 3.

  • Page 16: Blade Replacement

    4. Continue to feed line through tunnel until adjustments, the trimmer head must not line is centered (leaving equal amounts move/spin at idle speed. on each side). See illustration below. The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: Positioning S Engine will not idle when the throttle is re-...

  • Page 17: Troubleshooting Table

    S Check entire unit for loose screws, nuts, OTHER and bolts. Replace any damaged, broken, S Do not store gasoline from one season to or worn parts. another. S At the beginning of the next season, use S Replace your gasoline can if it starts to rust. only fresh fuel having the proper gasoline to oil ratio.

  • Page 18: Declaration Of Conformity

    EC Declaration of Conformity (Only applies to Europe) We, Husqvarna Outdoor Products Italia, S.p.A., Valmadrera, Italy. Tel: +39- -0341- -203211, declare that the brushcutter model McCulloch 2500CXL from serial numbers 2006- -258N00001 and onwards, comply with the requirements of the COUNCIL’S DIRECTIVES: of 22 June 1998 “relating to machinery”...

  • Page 19: Technical Data Sheet

    TECHNICAL DATA SHEET ODEL: 2500CXL Blade Trimmer ENGINE Displacement, cm Maximum engine power, measured in accordance with ISO 8893, kW ENGINE ROTATIONAL SPEEDS At maximum engine power, rpm 8000 8000 Maximum rotational frequency of the spindle 10000 10000 Engine speed at recommended maximum...

Table of Contents