Duration Of 1St Tone; Duration Of 2Nd Tone; Duration Of Single Tone; Gap Time - Kenwood TK-3180 Function Reference

21 2-TONE

21.2.1 Duration of 1st Tone

This function allows you to configure the 1st Tone Encode
configured in the 2-tone Encode Memory List.
You can configure the Duration of 1st Tone using KPG-
89D. Normally, configure this duration to 1 second.
!
Configuration using KPG-89D
• Configuring the Duration of 1st Tone (Refer to
FPRG 6.11.1 Encode tab - Duration of 1st Tone.)

21.2.2 Duration of 2nd Tone

This function allows you to configure the 2nd Tone
Encode transmit configured in the 2-tone Encode Memory
List.
You can configure the Duration of 2nd Tone using KPG-
89D. Normally, configure this duration to 3 seconds.
!
Configuration using KPG-89D
• Configuring the Duration of 2nd Tone (Refer to
FPRG 6.11.1 Encode tab - Duration of 2nd Tone.)

21.2.3 Duration of Single Tone

This function allows you to configure the Single Tone
Encode transmit time configured in the 2-tone Encode
Memory List.
You can configure the Duration of Single Tone using
KPG-89D. Normally, configure this duration to 5 seconds.
!
Configuration using KPG-89D
• Configuring the Duration of Single Tone (Refer to
FPRG 6.11.1 Encode tab - Duration of Single
Tone.)

21.2.4 Gap Time

This function allows you to configure the unmodulated
carrier time between the 1st Tone and the 2nd Tone
configured in the 2-tone Encode Memory List is
transmitted.
You can configure the Gap Time using KPG-89D.
Normally, configure this period to 0 ms.
!
Configuration using KPG-89D
•
Configuring the Gap Time (Refer to FPRG 6.10.1
Encode tab - Gap Time.)
90

21.2.5 First Tone Delay Time

The First Digit Delay Time is the delay time between the
time that the transceiver begins transmission and the time
that it ends the 2-tone transmission. The unmodulated
transmission is performed during the First Digit Delay
Time.
You can configure the First Tone Delay Time using KPG-
89D.
!
Configuration using KPG-89D
•
Configuring the First Tone Delay Time (Refer to
FPRG 6.10.1 Encode tab - First Tone Delay Time.)

21.2.6 Sidetone

This function allows the transceiver to monitor the 2-tone
transmission from the local speaker.
You can configure the 2-tone sidetone using KPG-89D.
!
Configuration using KPG-89D
• Configuring the Sidetone (Refer to FPRG 6.11.1
Encode tab - Sidetone.)

21.2.7 2-tone Encode Memory List

This is the code list for performing the 2-tone Encode
operation. The transceiver transmits the 2-tone when the
code configured in this list is selected.
You can configure the following functions in the 2-tone
Encode Memory List.
Table 21-1 Autodial List Configuration
Autodial List
Single Tone
2-tone Name
1st Tone
2nd Tone
Function Reference
Operation
This function allows you to configure the
transmission code as a Single Tone. You
cannot configure the 2nd Tone when
configuring the transmission code as a
Single Tone.
This function allows you to assign a name to
each List number. You can configure a
maximum of 12 characters to each number.
This function allows you to configure the 1st
Tone frequency. You can configure the
frequency between 288.5 and 3106.0 Hz.
This function allows you to configure the 2nd
Tone frequency. You can configure the
frequency between 288.5 and 3106.0 Hz.
You cannot configure the 2nd Tone when
configuring the transmission code as a
Single Tone.
Version: 1.11