TDK-Lambda GENESYS 10KW Manuals

Manuals and User Guides for TDK-Lambda GENESYS 10KW. We have 2 TDK-Lambda GENESYS 10KW manuals available for free PDF download: User Manual, Technical Manual

TDK-Lambda GENESYS 10KW User Manual (103 pages)

Programmable DC Power Supplies

Brand: TDK-Lambda | Category: Power Supply | Size: 2 MB

Table of Contents
7
Warranty
10
Safety Instructions
11
General Information
23
User Manual Content
23
Introduction
23
Accessories
25
Model Number Format
26
Specifications
27
Output Rating (Duty Cycle Continuous Duty)
27
Input Characteristics
27
Static Characteristics
27
Protective Functions
28
Dynamic Characteristics
28
Remote Analog Control and Signals
29
Front Panel
30
Software Spec
30
Digitial Programming and Readback
31
Mechanical Construction
31
Environmental Conditions
31
Emc
32
Safety
32
J1 Connector
33
Installation
34
General
34
Preparation for Use
34
Initial Inspections
34
Rack Mounting
35
Location, Mounting and Cooling
35
AC Source Requirements
35
AC Input Power Connection
35
Turn-On Checkout Procedure
37
Power Supply Output Turn-Off and Discharge Procedure
40
Connecting the Load
41
Local and Remote Sensing
45
Repackaging for Shipment
47
Front and Rear Panel Controls and Connectors
48
Introduction
48
Front Panel Controls and Indicators
48
Rear Panel Connections and Controls
51
Rear Panel SW1 Setup Switch
53
Rear Panel J1 Programming and Monitoring Connector
54
Local Operation
56
Introduction
56
Standard Operation
56
Over Voltage Protection (OVP)
57
Under Voltage Limit (UVL)
58
Foldback Protection
58
Output ON/OFF Control
59
Output SHUT-OFF (SO) Control Via Rear Panel J1 Connector
59
Enable/Disable Control Via Rear Panel J1 Connector
60
CV/CC Signal
60
PS_OK Signal
60
Safe Start and Auto-Restart Modes
61
Front Panel Locking
61
Over Temperature Protection (OTP)
62
Last Setting Memory
62
Series and Parallel Operation
63
Series Operation
63
Parallel Operation (Single-Wire/Two-Wire Method)
66
Remote and Analog Programming
76
Introduction
76
Local/Remote Analog Selection
76
Local/Remote Analog Indication
77
Remote Voltage Programming of Output Voltage and Current Limit
77
Resistive Programming of Output Voltage and Current Limit
79
Remote Monitoring of Output Voltage and Current
80
Rs-485 Remote Control
81
Introduction
81
Configuration
81
Rear Panel RS-232/RS-485 Connector
82
Connecting Power Supplies to the RS-232 or RS-485 Bus
83
Communication Interface Protocol
84
Error Messages
85
Command Set Description
86
Global Output Commands
89
Fast Queries
92
Status and Error Commands
93
Status, Error, and SRQ Registers
94
Serial Communication Test Set-Up
97
Isolated Analog Programming Option
99
Introduction
99
Specifications
99
Isolated Programming & Monitoring Connector
100
Setup and Operating Instructions
101
Maintenance
102
Introduction
102
Units under Warranty
102
Periodic Maintenance
102
Adjustments and Calibration
102
Parts Replacement and Repairs
102
Troubleshooting
102

TDK-Lambda GENESYS 10KW Technical Manual (74 pages)

TDK-Lambda Programmable DC Power Supplies

Brand: TDK-Lambda | Category: Power Supply | Size: 2 MB

Warranty

4
- Safety Instructions
  5
- Table of Contents
  7
Chapter 1 General Information

9
- User Manual Content
  9
- Introduction
  9
- Accessories
  11
- Model Number Format
  12
Chapter 2 Specifications

13
Chapter 3 Installation

17
- General
  17
- Preparation for Use
  17
- Initial Inspections
  17
- Rack Mounting
  17
- Locaton, Mounting and Cooling
  18
- Ac Source Requirements
  18
- Ac Input Power Connection
  18
- Turn-On Checkout Procedure
  20
- Connecting the Load
  22
- Local and Remote Sensing
  25
Chapter 4 Front and Rear Panel Controls and Connectors

28
Chapter 5 Local Operation

36
- Introduction
  36
- Standard Operation
  36
- Over Voltage Protection (Ovp)
  37
- Under Voltage Limit (Uvl)
  38
- Foldback Protection
  38
- Output On/Off Control
  38
- Output Shut-Off (So) Control Via Rear Panel J1 Connector
  38
- Enable/Disable Control Via Rear Panel J1 Connector
  39
- CV/CC Signal
  39
- Ps_Ok Signal
  39
- Safe Start and Auto-Restart Modes
  40
- Over Temperature Protecton (Otp)
  40
- Last Setting Memory
  40
- Series Operation
  40
- Parallel Operation
  43
- Daisy-Chain Connection
  44
- Advanced Parallel Operation
  44
- Front Panel Locking
  47
Chapter 6 Remote Analog Programming

48
Chapter 7 Rs232 & Rs485 Remote Control

52
- Introduction
  52
- Configuration
  52
- Rear Panel Rs232/485 Connector
  53
- Connecting Power Supplies to Rs232 Bus
  54
- Communication Interface Protocol
  55
- Error Messages
  56
- Command Set Description
  57
- Global Output Commands
  59
- Single Byte Commands
  60
- Status, Error and Srq Registers
  65
- Serial Communication Test Set-Up
  68
Chapter 8 Isolated Analog Programming Option

70
- Introduction
  70
- Specifications
  70
- Isolated Programming & Monitoring Connector
  71
- Setup and Operating Instructions
  72
Chapter 9 Maintenance

73
- Introduction
  73
- Units under Warranty
  73
- Adjustments and Calibration
  73
- Parts Replacement and Repairs
  73
- Troubleshooting
  73

TDK-Lambda Categories

Power Supply Media Converter Cables and connectors Racks & Stands Control Unit

More TDK-Lambda Manuals

TDK-Lambda GENESYS 10KW Manuals

TDK-Lambda GENESYS 10KW User Manual (103 pages)

Table of Contents

TDK-Lambda GENESYS 10KW Technical Manual (74 pages)

Table of Contents

Warranty

Chapter 1 General Information

Chapter 2 Specifications

Chapter 3 Installation

Chapter 4 Front and Rear Panel Controls and Connectors

Chapter 5 Local Operation

Chapter 6 Remote Analog Programming

Chapter 7 Rs232 & Rs485 Remote Control

Chapter 8 Isolated Analog Programming Option

Chapter 9 Maintenance

Related Products

TDK-Lambda Categories