1. Manuals
  2. Brands
  3. Yoda Manuals
  4. IP Phone
  5. VP306
  6. Quick installation manual

Yoda VP306 Quick Installation Manual

Sip voip
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
VP306 / VP306P
SIP
VoIP
Phone
Quick Installation Guide
&
User Manual
January 31, 2007
1

Advertisement

Table of Contents
loading

Related Manuals for Yoda VP306

Summary of Contents for Yoda VP306

  • Page 1 VP306 / VP306P VoIP Phone Quick Installation Guide & User Manual January 31, 2007...
  • Page 2 Quick Installation Guide Step 1: VP306 Keypads & Backplane Memory Dial 1st SIP Account 2nd SIP Account 3rd SIP Account Do Not Disturb Voice Message Speaker Phone MicroPhone...
  • Page 3 1. Connect VP306 RJ45 WAN port to ADSL NAT Router as the following connection. 2. Connect VP306 RJ45 LAN port to Notebook PC LAN port using a Category 5 LAN cable. 3. Connect DC Power Adaptor. The LCD Panel will start showing Loading Program! 4.
  • Page 4 For Network Settings, there are three choices for IP type in WAN Settings; Fixed IP, DHCP, and PPPoE. For Fixed IP, the user must key in static fixed IP address, Subnet Mask, and Gateway IP with DNS Server IP address. 1.
  • Page 5 5. The IE Web browser will show the following System Information page. 6. You need to set up the following web configurations: Phone, Network WAN/LAN Settings, SIP Settings. Remember to submit, save and reboot for new configurations. 7. For WAN settings DHCP: This is for Dynamic IP address and is commonly selected for WAN IP address when NAT is selected.
  • Page 6 Bridge LAN mode: The Bridge LAN mode can be selected when NAT is not needed. In this case, the WAN and LAN port are transparent as Ethernet Bridge Hub. Note that the embedded NAT is enabled at default. 8. SIP Settings: You may configure up to 3 SIP registration accounts with the 3 realms in Service Domain Settings.
  • Page 8 SIP Account Number Selections With 3 SIP account registered numbers, the VP306 may receive all the incoming calls from the 3 SIP servers. Realm 1, 2, and 3 are used to configure the registered numbers for the 1st, 2nd, and 3rd SIP servers, respectively. VP306 may register different phone numbers to different SIP servers.
  • Page 9 VP306 / VP306P SIP VoIP Telephone User Manual V2.1f...

  • Page 10: Table Of Contents

    Table of Content 1. Introductions 2. Features 3. Standard Compliances 4. Packing Contents 5. LED Indicators 6. Installations & SIP Configurations 7. Default Reset by Using Keypads 8. Configurations by Web Browser 9. LCD Display with Keypads Settings 10. VoIP Application Examples 11.

  • Page 11: Introductions

    The VP306 is an IP Telephone with SIP Protocols for Voice over IP (VoIP) applications. Connecting to the Internet, the VP306 can make a VoIP call over the Internet. The VP306 provides one WAN port for Internet ADSL connections, and one LAN port for Notebook PC.

  • Page 12: Standard Compliances

    Please check if the packing is damaged or any component is missing. If so, please contact your distributor. 5. LED Indicators On the front panel of VP306, there are three LED indicators as the following REG: “Green On” indicates successful registration at SIP server.

  • Page 13: Installations & Sip Configurations

    6. Installations & SIP Configurations Connect VP306 RJ45 WAN port to NAT Router using a Category 5 LAN cable. Connect RJ45 LAN port to Notebook PC using a Category 5 LAN cable. Connect DC Power Adaptor. The LCD Panel will start displaying ”Loading...

  • Page 14: Configurations By Web Browser

    8. Configurations by Web Browser You may enter the IP address from PC Web browser to configure VP306. For example, enter http://192.168.123.1:9999 from IE web browser to display login page as follows. 8.1. Please enter the default IP address http://192.168.123.1:9999 from PC Web browser.

  • Page 15: System Information

    System Information 8.4. The system information shows firmware version, Codec, etc. 8.5. You may click the buttons, for example Phone Book, at the left hand side to configure the VP306. Phone Book Phone Book Settings 8.6. You may add/delete Name up to maximum 140 entries in Phone book list.
  • Page 16 Press 201# on telephone, and VP306 will call the registered number 14081234567. Example 3: Name: 301, URL: 192.168.1.100:5062 Press 301# on telephone, and VP306 will call at 192.168.1.100 with port 5062. Example 4: No Name 401 in phone book. Press 401# on telephone, and VP306 will call the registered number 401.
  • Page 18 Speed Dial Phone List 8.11. You can add/delete Speed Dial number up to maximum 10 entries in Speed Dial Phone List. 8.12. If you need to add a phone number into the Speed Dial list, you need to enter the position, the name, and the URL.

  • Page 19: Phone Setting

    Phone Setting Call Forward 8.14. You can select the forward mode and enter the forward URL. All Forward: All incoming call will forward to the URL you choose. Busy Forward: The incoming call will forward to the URL when you are busy and on the phone. No Answer Forward: The incoming call will forward to the URL when no answer.
  • Page 20 SNTP 8.16. You can setup the primary and the second SNTP Server IP Addresses to get the date/time information. You may also set the Time Zone, and how long need to synchronize again. When you finished the setting, please click the “Submit” button.
  • Page 21 Handset/Speaker Volume is to set the volume hearing from the handset/Speaker. Handset Gain is to set the volume send out from the handset. Speaker Gain is to set the volume send out from the microphone at the bottom of VP306. Melody...
  • Page 22 8.19. You can setup the DND (Do Not Disturb) to keep the phone slience. You can choose DND Always or DND period. . DND Always: All incoming call will be blocked until the feature is disabled. DND Period: Set a time period and the phone will be blocked during the time period. If the “From”...
  • Page 24 8.24. Click the Save button. The changes you have made will be saved and the VP306 will reboot automatically.
  • Page 25 Pick Up & Voice Mail 8.27. VP306 may pick up the incoming call for another VP306 when registered in the same IP PBX. When you hear other VP306 is ringing, you may pick up you phone and press Pick Up function key to answer for that VP306.
  • Page 26 8.29. You can enable/disable and set Hot Line phone number in this page. 8.30. When Hot Line mode is enabled, you just pick up the phone and the VP306 will call the Hot line number immediately. The default for Hot Line mode is disabled.
  • Page 27 8.33. VP301 supports each instant short text message (160 characters) with maximum 30 messages, If recived the messages surpass 30 will over-write from frist message . The LCD play "Got Message" is indicate have recived short text messages, Press Menu / 3. Phone Setting / 8. SMS of Keypad can read the short text message and also can follow the webpage to read, send, replay or delete the short text messages.
  • Page 28 8.2. Network 8.34. You can check the Network status, and configure the WAN, LAN, DDNS, and VLAN settings in this section. Network Status 8.35. You can check and show the current Network setting in this page.
  • Page 29 WAN Settings 8.36. The WAN setting is used to configure the Ethernet port connects to the ADSL Modem/Router. 8.37. The default setting is NAT mode for IP PHone, and this enables the embedded NAT router between the LAN port and PC port. You may change to Bridge Mode if you need NOT use the embedded NAT router.
  • Page 30 LAN Settings 8.42. The default IP address is 192.168.123.1 for VP306, with Net Mask 255.255.255.0., and DHCP Server enabled. The IP addresses for DHCP are from 150 to 200. 8.43. Connect your PC to the PC port, set your PC as DHCP Client mode, and then the PC will get an IP address from the VP306 automatically.
  • Page 31 DDNS Settings 8.45. You can configure the DDNS setting in this page. You need to have the DDNS account and input the informations properly. You need a DDNS account with a public IP address then others can call you via the DDNS account. Most of the VoIP applications are working with a SIP Proxy Server as well as DDNS Server.
  • Page 32 VLAN Settings 8.46. The VLAN setting is for VoIP packets related to WAN port. 8.47. VLAN Packets: If you enable VLAN Packets and set the VID, User Priority, and CFI, then all the incoming packets will be checked with the IP Address and the VID. 8.48.
  • Page 33 8.52. The DMZ can be enabled/disabled and configured in this page.
  • Page 34 Virtual Server 8.53. The Virtual Server IP and Port numbers can be configured in this page. PPTP Setting 8.54. The PPTP Server can be set ON/OFF in this page.

  • Page 35: Sip Settings

    8.55. You can setup the Service Domain, Port Settngs, Codec Settings, RTP Setting, RPort Setting and Other Settings for SIP Proxy Server registrations in this page. 8.56. You may register up to three SIP Servers for three Realms in the VP306. You can receive the incoming calls from all the three SIP Servers.
  • Page 36 Click selection?
  • Page 37 Port Settings 8.67. The SIP Port and RTP Port numbers are default at 5060 and 60000, respectively. The RTP port number must be even number. If you have more than one VoIP phones under the same NAT router, it is recommended that different RTP port numbers be assigned to each of IP Phones. Codec Settings 8.68.
  • Page 38 Codec ID Settings 8.69. You can set the Codec ID to meet the other device’s requirement. When you finished the setting, please click the Submit button.
  • Page 39 DTMF Settings 8.70. You can setup the options for DTMF function in this page. The options include RFC2833 (Outband DTMF), Inband DTMF, and Send DTMF SIP info. If you are making two-stage callings for extension to PSTN, you might need to select RFC2833 DTMF option.
  • Page 40 RPort Function 8.71. You can enable/disable the RPort in this page. To change this setting, please follow your ISP information. When you finished the setting, please click the Submit button. Other Settings 8.72. You can setup the Hold by RFC and QoS in this page. To change these settings please follows your ITSP information.

  • Page 42: Nat Trans

    NAT Trans STUN 8.73. You can Enable/Disable and configure STUN Server IP address in this page. This function helps IP Phone working properly behind NAT. To change these settings please follow your ISP information. When you finished the setting, please click the Submit button.
  • Page 43 Others 8.74. You can setup Auto Config, MAC Clone, Tone and Some Advanced Settings in this page. Auto Configuration Setting 8.75. Auto Configuration function can be used to download the configuration file stored in the TFTP, HTTP, or FTP server. This function must co-work with the Auto Config Server. After enabling the function, please click the “Submit”...
  • Page 44 MAC Clone 8.76. The MAC Clone function is to clone the MAC when only one MAC is available from ITSP. This is to share with the PC using the same MAC. When you finished settings, please click the Submit button. Tone 8.77.
  • Page 45 Advanced Setting 8.78. The advanced settings might be useful for some network requirements. The ICMP function is to echo when someone ping this device. This can prevent from haker attacking the device by not echoing. When you finished the setting, please click the Submit button. IP Dialing format (P2P dialing): There are 3 options.

  • Page 46: System Authority

    Syslog 8.79. You can check system status log . System Authority 8.80. The user login name and password can be changed in this page.

  • Page 47: Save Change

    Save Change 8.81. If you want to save the changes you have made for new setting in the VoIP Phone, You have to click the Save button. After you click the Save button, the VoIP Phone will automatically restart and the new setting will get effective.
  • Page 48 Update Update Firmware 8.82. The IP Phone provides two methods, HTTP or TFTP, to update new firmware as the following steps: 8.83. Select the firmware code type, Risc or DSP code. (mostly for Risc code) 8.84. Click the “Browse” button to choose the updated file location for HTTP download, or 8.85.
  • Page 49 Auto Update Settings 8.86. The IP Phone provides two methods, HTTP or TFTP, to update new firmware as the following steps:...
  • Page 50 Restore Default Settings 8.87. You can restore the VoIP Phone to factory default in this page. Click the Restore button, then the IP Phone will restore to default and automatically restart again. Reboot 8.88. If you want to restart the VoIP Phone, you can just click the Reboot button, and then the VoIP Phone will restart automatically.

  • Page 52: Lcd Display With Keypad Settings

    LCD Display with Keypad Settings: 1. Phone Book 1.1 Search: Search Phone Book. 1.2 Add entry: Add new phone number to phone book. 1.3 Speed dial: Add speed dial phone number to speed dial list. 1.4 Erase all: Erase all phone number from Phone Book. 2.
  • Page 53 4. Network 4.1 WAN Setup: 4.1.1 IP Type: 4.1.1.1 Fixed IP client 4.1.1.2 DHCP client: 4.1.1.3 PPPoE client: 4.1.2 Fixed IP setting: 4.1.2.1 Host IP 4.1.2.2 Subnet mask 4.1.2.3 Gateway IP 4.1.3 PPPoE setting: 4.1.3.1 User name 4.1.3.2 Password 4.2 LAN Setup: 4.2.1 Bridge 4.2.2 NAT 4.3 DNS Server:...
  • Page 54 5.3 RTP Setting: 5.3.1 Outband DTMF: Outband DTMF Enabled/Disabled. 5.3.2 Duplicate RTP 5.3.2.1 No duplicate: No resend voice packets. 5.3.2.2 One duplicate: Resend voice packets once. 5.3.2.3 Two duplicate: Resend voice packets twice. 5.4 RPort Setting: RPort Enabled/Disabled. 5.5 Hold by RFC: Hold by RFC3261 Enabled/Disabled.

  • Page 55: Voip Application Examples

    10. VoIP Application Examples You can use PC Web browser to configure VP306. For example, enter http://192.168.123.1:9999 from PC web browser. A. ADSL Connections without NAT Router for VP306 INTERNET ADSL Modem For VP306P PSTN PSTN Phone IP: 192.168.123.1 B. ADSL Connections with NAT Router for VP306...
  • Page 56 Example 1: SIP-to-SIP Calling/Answering Applications: The SIP-to-SIP calling works when both calling and answering parties are registered to SIP server with given registered phone numbers. The ADSL connections can be as in either Diagrams A or B. Both parties are registered to SIP server under NAT router. For Diagram A without NAT router, you may select NAT mode to enable the embedded NAT router.
  • Page 57 Example 3: Direct IP to Direct IP Calling/Answering Applications: The applications are for ADSL connection without NAT router as in Diagram A. Both parties are with fixed real IP. The Direct IP calling works when both calling and answering parties are with known fixed IP.
  • Page 58 Example 5: 3-Way Conference Call, Call Transfer, Call Waiting, Hold Applications: The Call Transfer and 3-Way Conference Call applications are for calls among Parties A, B, and C. Three parties are registered to SIP server with either fixed real IP or private IP. There are two kinds of call transfer;...

  • Page 59: Trouble Shooting For Web Configurations

    PSTN PSTN IP: 192.168.123.1 Example: To change VP306 IP address to the same subnet as PC and NAT router 1. Press the menu to enable DHCP Client mode. VP306 will reboot, and LED will start flasing to get an IP address from NAT DHCP server.
  • Page 60 11.3. CONFIGURE PC’S IP SETTINGS FOR VP306 EMBEDDED NAT FUNCTION? If you don’t have a router to connect both PC and VP306 for sharing the only one IP address from ADSL/Cable modem, you should enable the embedded NAT function inside VP306.

This manual is also suitable for:

Vp306p

Table of Contents