Door Disassembly - Frigidaire GLBM188HB Service Manual

GLBM188HB
8. Lift up the door assembly to release the upper and lower door
hinge pins from the upper and lower oven hinges.
9. Now, the door assembly is free.
NOTE: When the individual parts are replaced, refer to "Door Disas-
sembly".
2. REINSTALL
1. On re-installing door, insert the lower oven hinge to lower door
hinge pin.
2. Insert the upper oven hinge to the upper door hinge pin.
3. Shut the door (close the contacts of interlock switches).
4. Make sure upper and lower oven hinges are inserted into the upper
an lower door hinge pins.
5. Make sure the door is parallel with oven face lines (left and upper
side lines) and door latch heads pass through latch holes correctly.
6. Re-install the door stopper to the door assembly.
7. Re-install the hood louver to the oven cavity front face plate.
NOTE: After any service to the door;
1) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to chap-
ter "Test Procedures".).
2) An approved microwave survey meter should be used
to assure compliance with proper microwave radiation
emission limitation standards.
3. After any servicing, make sure of the following:
1. Door latch heads smoothly catch latch hook through latch holes
and that latch head goes through center of latch hole.
2. Deviation of door alignment from horizontal line of cavity face plate
is to be less than 1.0mm.

[21] DOOR DISASSEMBLY

1. Disconnect the power supply cord and remove the oven from wall
and remove outer case. (Refer to procedure of "Removal of Oven
from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood louver from the oven cavity. (Refer to the proce-
dure of "HOOD LOUVER REMOVAL".)
5. Remove door assembly, refer to "Door Replacement". Replace-
ment of door components are as follows:
6. Place door assembly on a soft cloth with latches facing up.
NOTE: Note: As the engaging part of choke cover and door frame are
provided at 16 places, do not force any particular part.
CHOKE COVER
7. Insert a putty knife (thickness of about 0.5mm) into the gap A
between the choke cover and door stopper and between the choke
cover and the door frame as shown Figure C-3 to free engaging
parts.
8. Pry the choke cover by inserting a putty knife in order shown in Fig-
ure C-3.
9. Now choke cover is free from door panel and door frame.
LATCH SPRING, LATCH HEAD AND DOOR PANEL
10.Release the latch spring from the tab of the latch head and tab of
the door panel.
11.Release the latch head from the door panel.
12.Now, the latch spring, latch head and door panel are free.
DOOR FRAME
3. Door is positioned with its face pressed toward cavity face plate.
4. Re-install outer case and check for microwave leakage around
door with an approved microwave survey meter. (Refer to Micro-
wave Measurement Procedure.)
NOTE: The door on a microwave oven is designed to act as an
electronic seal preventing the leakage of microwave
energy from oven cavity during cook cycle. This function
does not require that door be air-tight, moisture (conden-
sation)-tight or light-tight. Therefore, occasional appear-
ance of moisture, light or sensing of gentle warm air
movement around oven door is not abnormal and do not
of themselves indicate a leakage of microwave energy
from oven cavity.
Upper Door
Hinge Pin
RE-INSTALL
Door assembly
Latch
Heads
Figure C-2. Door Replacement and adjustment
13.Remove eight (8) screws holding the door panel to the door frame
assembly.
14.Release the door frame assembly from the door panel.
NOTE: NOTE: It is easier to release the engaging parts of the upper
or lower door hinge pin side at first.
15.Now, door frame assembly is free.
Choke Cover
Figure C-3. Door Disassembly
DISPLAY UNIT
16.Remove two (2) screws holding the control unit cover to the door
flame assembly.
17.Release the control unit cover from the door flame assembly.
18.Disconnect the connect CN-J from the display unit.
Page 35
11 – 7
Hood Louver
Upper
Oven
Hinge
Lower
Oven Hinge
Lower Door
Hinge Pin
RE-INSTALL
Door Stopper
A
Putty Knife
Door Frame