Turntable Motor Removal; Antenna (Stirrer) Motor Removal; Stirrer Cover And Antenna Installation; Oven Lamp Removal - Frigidaire GLBM188HB Service Manual

GLBM188HB

[12] TURNTABLE MOTOR REMOVAL

1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three(3) screws holding the deflector to the cavity face
plate.
4. Remove the four (4) screws holding the base cover to the oven
cavity.
[13] ANTENNA MOTOR REMOVAL
1. Disconnect the power supply cord and remove the oven from wall
and outer case. (Refer to procedure of "Removal of Oven from
Wall" and Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood duct from the oven cavity, referring to the proce-
dure of "HOOD FAN MOTOR, HOOD DUCT AND OVEN LAMP
SOCKET REMOVAL".
[14] STIRRER COVER AND STIRRER ANTENNA INSTALLATION
1. Put the stirrer antenna fan on the wave guide to match the stirrer
antenna shaft to the center of the stirrer hole.
2. Insert the shaft of stirrer antenna to the shaft of stirrer antenna
motor.
3. Rotate the antenna holder to lock at the cavity top plate.
4. Insert the cutout of stirrer cover to the tabs on the ceiling.
5. Install the stirrer cover to the oven cavity, and secure it by one
canoe clip

[15] OVEN LAMP REMOVAL

1. Disconnect the power supply cord.
2. Remove the hood louver from the oven. (Refer to procedure of
"HOOD LOUVER REMOVAL")
3. Lift the oven lamp cover up.
[16] POSITIVE LOCK CONNECTOR (NO-CASE TYPE) REMOVAL
1. Disconnect the power supply cord and remove the oven from wall
and outer case. (Refer to procedure of "Removal of Oven from
Wall" and Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock
5. Pull down on the positive lock
CAUTION: WHEN CONNECTING THE POSITIVE LOCK
TORS TO THE TERMINALS, INSTALL THE POSITIVE
LOCK SO THAT THE LEVER FACES YOU.

[17] RIGHT PANEL ASSEMBLY AND POWER UNIT REMOVAL

1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the hood louver from the oven. (Refer to procedure of
"HOOD LOUVER REMOVAL")
4. Remove one (1) screw holding the right panel to the oven cavity
front face plate.
5. Release the right panel from the oven cavity front face plate by lift-
ing it up.
connector.
connector.
CONNEC-
5. Remove the base cover from the oven cavity by pulling down and
moving to the left slightly.
6. Disconnect the wire leads from the turntable motor.
7. Remove one (1) screw holding turntable motor to the oven cavity.
8. Now the turntable motor is free.
5. Disconnect the wire leads from the antenna motor.
6. Remove the one (1) screw holding the antenna motor to the
waveguide of the oven cavity.
7. Remove the antenna motor from the waveguide.
8. Now, the antenna motor is free.
9. When installing the antenna motor, the shaft of antenna motor must
be inserted to the antenna shaft. Refer to the procedure of "STIR-
RER COVER AND STIRRER FAN INSTALLATION".
Canoe Clip
4. Now, the oven lamp and the socket are found.
5. Screw the oven lamp off from the lamp socket.
6. Now, the oven lamp is free.
Positive lock¨
connector
Lever
Positive lock , connector
6. Disconnect the wire leads from the relays RY1 and RY2.
7. Disconnect the connectors CN-A, CN-B, CN-C, CN-D, CN-E and
CN-F from the control unit.
8. Remove the right panel assembly from the oven.
9. Now, the right panel assembly is free.
10.Remove four (4) screws holding the power unit to the key fixing
plate and right panel.
11. Now, the power unit is free.
Page 33
11 – 5
Shaft
Stirrer Antenna
Stirrer Cover
Terminal
1
Push
2
Pull down