Marantz RC3001 User Manual
  1. Manuals
  2. Brands
  3. Marantz Manuals
  4. Remote Control
  5. RC3001
  6. User manual

Marantz RC3001 User Manual

Marantz user guide remote controller rc3001
Hide thumbs
Table of Contents

Advertisement

Quick Links

Model RC3001 User Guide
Remote Controller

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RC3001 and is the answer not in the manual?

Questions and answers

Related Manuals for Marantz RC3001

Summary of Contents for Marantz RC3001

  • Page 1 Model RC3001 User Guide Remote Controller...
  • Page 2 For US and Canada Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 3 Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty ser vice, it is the responsibility of the consumer to establish proof and date of purchase.
  • Page 4 English WARNINGS - Do not expose the equipment to rain or moisture. - Do not remove the cover from the equipment. - No naked flame sources, such as lighted candles, should be placed on the equipment. - When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.
  • Page 5 A NOTE ABOUT RECYCLING This product’s packaging materials are recyclable and can be reused. This product and the accessories packed together are the applicable product to the WEEE directive except batteries. Please dispose of any materials in accordance with your local recycling regulations. When discarding the unit, comply with your local rules or regulations.

  • Page 6: Table Of Contents

    Thank you for purchasing the Marantz RC3001 remote controller. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you operate the RC3001.

  • Page 7: Load The Rechargeable Battery Pack Into The Remote Controller

    Remote controller becomes unreliable. If you want to order new batteries, please contact your Marantz authorized dealer or Marantz customer service. Warning: Replace the batteries only with original Marantz RC3001 batteries; otherwise the guarantee is no longer valid and hazardous situations could occur.

  • Page 8: Charging The Battery Pack

    CHARGING THE BATTERY PACK Once the rechargeable battery pack is loaded, power is immediately supplied automatically to the remote controller, and Home mode is displayed on the LCD. When it is fi rst unpacked, the supplied battery pack is not fully charged. Be sure to fully charge it before usage.

  • Page 9: Names And Functions

    NAMES AND FUNCTIONS REMOTE CONTROLLER POWER ON and OFF buttons These buttons are used when controlling devices that have been set with separately powered on and off remote commands. SOURCE ON/OFF button This button is used when controlling devices that have been set with a single power on/off remote command.

  • Page 10: Remote Controller Lcd

    USB port This port is used to connect the remote controller and a PC with the supplied USB cable to enable editing with the Wizz.it 3 editor software. REMOTE CONTROLLER LCD Charging terminal This terminal is used to connect the supplied AC adapter used to charge the remote controller.

  • Page 11: Rx3001

    1 to 3 and IR output jacks 4 to 6. CH selector switch This switch sets the reception channel. Set to the same channel as the RC3001. Note: The CH selector has eight setting positions, but only four channel positions can be set.

  • Page 12: Installation

    • Do not mount the RX3001 so that it sticks out from the wall edge. It could get hit by people s bodies or objects and cause an injury. • Marantz will not be liable for any accidents or injuries that occur due to improper mounting or handling.
  • Page 13 The positional relationship between the RX3001 key holes and the screw mounting positions are shown in the fi gure below. Notes: • When mounting the screws to the wall, leave a space between the wall and screw cap as shown in the fi...

  • Page 14: Using The Remote Controller With Infrared Rays

    IR Emitters referring to page 10, 11. The devices will always receive IR signals either 1 INP directly from the RC3001 or from the RX3001. Precaution: This product would not perform normally under a strong electrostatic environment.

  • Page 15: Connecting The Rx3001 With Other Devices

    CONNECTING THE RX3001 WITH OTHER DEVICES 1. CONNECTING TO MARANTZ EQUIPMENT Note: When connecting to other equipment, set the REMOTE CONTROL switch on the rear panel of the connected equipment to EXT. RC3001 Remote controller SA-CD Player CD Changer OPEN/CLOSE...
  • Page 16 2. CONNECTING TO NON-MARANTZ EQUIPMENT Notes: • When affi xing the IR emitter, be sure to affi x it in front of the IR receiver of the equipment to which it will be connected. • Do not connect a commercial dual IR emitter to the IR output jack. In some cases, this could disable operation.

  • Page 17: Setup

    LEVEL SW 1 SETTING THE CHANNEL Use the CH selector knob to set to the same channel as the RC3001. Notes: • When setting the channel with the CH selector, the available channels are CH1 to CH4 with two setting positions for each channel.

  • Page 18: Setting The Group Id Selector

    SETTING THE GROUP ID SELECTOR The RC3001 can use the Wizz.it 3 editor to set the group ID for each device. If a different ID signal is sent from the remote controller, no control signal is output from the RX3001.

  • Page 19: Basic Operation

    • This is a convenient function for devices that do not have a sleep timer or for setting the sleep timer using multiple devices. • The RC3001 performs regular operation even when the sleep timer is activated. Press the button that will be assigned to the sleep timer.

  • Page 20: Other Operation

    2 inches (0.05 m). Display the MAIN MENU on the LCD of the RC3001, and then press the button next to the LEARNING indicator. The screen appears as shown below. Either press the ENTER button or wait for...
  • Page 21 Learning cannot be performed when a special remote controller signal code is used. • The RC3001 can learn up to a maximum of 1,000 remote controller codes. Once 1,000 codes are programmed for learning, LEARNFULL is displayed on the LCD, and learning can no longer be performed.

  • Page 22: Timer

    2. TIMER The timer function of the RC3001 can be used to send a preset remote controller command at a programmed time. The Wizz.it 3 editor can be used to operate multiple devices. One Touch Operation (Macro) can also use the timer function for transmission.
  • Page 23 Home mode is shown in the LCD. Select the commands and devices for the commands that will be sent by timer programming. • I f a c o m m a n d a s s i g n e d t o t h e HARD button is to be sent by timer programming, press the HARD button when selecting the command to make...
  • Page 24 OPERATION ON/OFF SETTINGS Press the button next to the ON/OFF indicator in the TIMER menu screen on the LCD to display the timer operation ON/OFF setting screen. Press the button next to the TIMER ON (Enable) or TIMER OFF (Disable) indicators on the LCD to either enable or disable timer operation.

  • Page 25: Sys.setup

    3. SYS.SETUP Display the MAIN MENU on the LCD of the RC3001, then press the button next to the SYS. SETUP indicator. The items below can be set in the SYS.SETUP screen. • CLOCK (Clock setting) • BACK LIGHT (Backlight illumination time setting) •...
  • Page 26 BACK LIGHT (BACKLIGHT ILLUMINATION TIME SETTING) Press the LIGHT button on the RC3001 to turn on the backlight, then set the time until the backlight turns off. Press the button next to the BACKLIGHT indicator in the SYS.SETUP menu screen in the LCD to display the backlight illumination time setting screen.
  • Page 27 The LCD setting menu is displayed. LCD TIMER (LCD timer setting) This sets the time that the LCD remains on, after a button is pressed on the RC3001. When there are no operations and the LCD is turned off, this setting enables power consumption to be reduced and the life of the battery pack to be extended.
  • Page 28 • Pressing the Home button returns the LCD to the MAIN MENU. BEEP (BEEP SOUND SETTING) This sets the built-in beep sound in the RC3001. Press the button next to the BEEP indicator in the SYS.SETUP menu screen in the LCD to display the beep setting screen.
  • Page 29 MEM CLEAR (INITIALIZATION SETTING) This returns the settings made in the RC3001 to their initial settings. Press the button next to the MEM CLEAR indicator in the SYS.SETUP menu screen in the LCD to display the initialization setting screen. Press the button next to the NO (Disable) or YES (Enable) indicators on the LCD to either enable or disable initialization.

  • Page 30: Status Indicator

    LCD returns to the MAIN MENU. 5. RESET If the RC3001 is not operating properly, use the procedure below to perform a reset (restart). Performing a reset does not erase the settings in the RC3001.

  • Page 31: Specifications

    SPECIFICATIONS RC3001 LCD Resolution ...“11x81pixel x6 line ...9x81pixel x1line” Backlight ... EL back light Transmission ...IR or RF Learning ... Capability: MAX 1000code Operating/ learning IR frequency range ...Up to 455kHz RF carrier frequency ... 433.92MHz Rechargeable battery pack ...NiMH Battery Pack 700 mAh Interface ..
  • Page 32 RX3001 RF carrier frequency ... 433.92MHz Operating/ learning IR frequency range ...Up to 100kHz IR emitter output ...x6 Dimensions (W x H x L) ... 102 x 63.5 x 27 mm (4-1/16 x 2-1/2 x 1-1/8 ins.) Unit Weight ... 90g (0.2lbs) AC Adapter Power Supply ...

  • Page 33: Others

    In the event of diffi culty, refer to your dealer or write directly to the nearest location to you that is listed on the Marantz Authorized Service Station list. If writing, please include the model and serial number of the equipment together with a full description of what you think is abnormal about the equipment s behaviour.
  • Page 34 You can find your nearest authorized distributor or dealer on our website. is a registered trademark. Printed in China 09/ 2007 00M43CW851010 mzh-d...

Table of Contents