Page 1
Vertrieb von CAMBOARD Electronics DVI CAT-5 Extender U S E R M A N U A L www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203 www.gefen.com...
Vertrieb von CAMBOARD Electronics TABLE OF CONTENTS Introduction DVI CAT-5 Extender Sender Front Panel Descriptions DVI CAT-5 Extender Receiver Front Panel Descriptions How To Connect The DVI CAT-5 Extender Dip Switch Usage Guide CAT5 Link Cable - Wiring Diagram Mounting Plate Installation Specifi...
Page 4
READ THESE NOTES BEFORE IN STALL ING OR OPERATING THE DVI CAT-5 EXTENDER • The DVI CAT-5 Extender is housed in a metal box for better RF shielding. • Your CAT-5 cable should not exceed 150 feet. • If you don't need DDC data you can use a single CAT-5 cable for the video only. The DDC will not be connected.
DVI source to the send unit. The DVI CAT-5 Extender receiver unit sits next to your DVI display - up to 150 feet away. The display plugs into the back of the DVI CAT-5 Extender receiver unit. Two CAT-5 cables connect the DVI CAT-5 Extender-S and the DVI CAT-5 Extender-R units to each other.
Vertrieb von CAMBOARD Electronics DVI CAT-5 EXTENDER SENDER FRONT PANEL DESCRIPTIONS Connects to 5 volt DVI input connects to power supply DVI source CAT-5 carries CAT-5 carries TMDS signals DDC/HDCP signals www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
Vertrieb von CAMBOARD Electronics DVI CAT-5 EXTENDER RECEIVER FRONT PANEL DESCRIPTIONS Connects to DVI display Connects to 5 volt power supply CAT-5 carries CAT-5 carries DDC/HDCP signals TMDS signals www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
Connect your source to the DVI Extender sender unit Connect your CAT-5 cables between the sender and the receiver Plug the 5V power supply into the DVI CAT-5 Extender sender unit You should now have picture. If you do not see a picture, try unplugging and re- plugging the DVI input on the DVI Extender sender unit.
CAMBOARD Electronics DIP SWITCH USAGE GUIDE Gefen CAT5 Extenders (sender and receiver) both contain a pair of dip switches located on the board. These dip switches are used to select from a set of confi gurations that will equalize the signal to best match the conditions in your setup.
im Vertrieb von CAMBOARD Electronics MOUNTING PLATE INSTALLATION www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
Page 12
im Vertrieb von CAMBOARD Electronics SPECIFICATIONS Video Amplifi er Bandwidth ................. 1.65 GHz Vertical Frequency Range .................. 50-60 Hz Single Link Range ..................1920 x 1200 Input Video Signal...................1.2 volts p-p Input DDC Signal....................5 volts p-p DVI Input Connector Type ..................DVI-D DVI Output Connector Type ..................
Gefen Inc. warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen Inc. is notifi ed within one (1) year from the date of shipment, Gefen System will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical or other abuse or modifi...
Need help?
Do you have a question about the DVI CAT-5 and is the answer not in the manual?
Questions and answers