Saving Patch Or Performance Settings (Write) - Roland XPS-10 Owner's Manual

Effect parameter
Effect Parameter
CURSOR [ K ] [ J ]
[SHIFT] +
CURSOR [ K ] [ J ]
SWITCH (MFX
1–3 switch)
00: THRU–78:
(MFX Type)
MFX1, MFX2,
Items for each
MFX3
MFX type
MFX CHO LVL 0–127
MFX REV LVL
SWITCH
(Chorus
switch)
CHORUS
00: OFF–03:
GM2 CHORUS
(Chorus Type)
Items for each
chorus type
SWITCH
(Reverb
switch)
REVERB
00: OFF–05:
GM2 REVERB
(Reverb Type)
Items for each
reverb type
3.
Press the [EXIT] button to exit the edit screen.
NOTE
The changes you make are temporary; they will be discarded when you
turn off the power or select a different tone. If you want to keep the
changes you make, you must write them into memory.
MEMO
. MFX1 uses the settings of the patch used by part 1.
. MFX2 uses the settings of the patch used by part 2.
. MFX3, chorus, and reverb settings are saved within each individual
performance.
Value Explanation
VALUE [-] [+]
Specifies whether MFX 1–3 will
be used (ON) or not used (OFF).
* This setting is common to
OFF, ON
the entire XPS-10.
* This setting cannot be
saved.
Selects the types of
multi-effects that MFX1–3 will
use.
00–78
Choose "00: THRU" if you don't
want to apply a multi-effect.
The editable items for the selected MFX type
will be displayed.
Refer to p. 39 for a list of multi-effect types.
Refer to "Parameter Guide" (PDF) for details
on the parameters.
Adjusts the amount of chorus
for the sound that passes
through multi-effects.
If you don't want to add the
chorus effect, set it to "0. "
Adjusts the amount of reverb
for the sound that passes
through multi-effects.
0–127
If you don't want to add the
reverb effect, set it to "0. "
Specifies whether chorus will
be used (ON) or not used (OFF).
* This setting is common to
OFF, ON
the entire XPS-10.
* This setting cannot be
saved.
Selects the types of chorus.
00–03
Choose "00: OFF" if you don't
want to apply a chorus.
Edit the parameters for the selected chorus
type.
Refer to "Parameter Guide" (PDF).
Specifies whether reverb will
be used (ON) or not used (OFF).
* This setting is common to
OFF, ON
the entire XPS-10.
* This setting cannot be
saved.
Selects the types of reverb.
00–05
Choose "00: OFF" if you don't
want to apply a reverb.
Edit the parameters for the selected reverb
type.
Refer to "Parameter Guide" (PDF).
Saving Patch or Performance Settings
(WRITE)
1.
Hold down the [SHIFT] button and press the [MENU]
(WRITE) button.
The WRITE screen appears.
MEMO
This screen is not shown in Patch mode.
2.
Use the CURSOR [ K ] [ J ] buttons to select "PATCH (Part
1–16)" or "PERFORM."
<WRITE> [ENT]
PERFORM *
If the selected performance has been edited, an "*" symbol is shown. This
symbol disappears when you save the settings.
NOTE
If an "*" symbol is shown for both PATCH (Part 1–16) and PERFORM, first
save the patch and then save the performance.
Be aware that if you save the performance first, the edited patch data is
lost.
3.
Press the [ENTER] button.
The name input screen appears.
Name: [ENT]
Init Perform
4.
Use the CURSOR [ K ] [ J ] buttons to move the cursor, and
use the VALUE [-] [+] buttons to select characters.
5.
When you've specified the name, press the [ENTER]
button.
To:501
[ ]
6.
Use the VALUE [-] [+] buttons to select the save-
destination.
Settings you save are stored in user memory, starting with number 501.
Drum kits are numbered starting with 801.
MEMO
If you specify a number in which data is already saved, the patch name
(performance name) is shown in the lower line.
NOTE
When you save settings, the data that was previously in that location
will be overwritten.
7.
Specify the save-destination number and press the
[ENTER] button.
A confirmation message appears.
8.
Press the [ENTER] button.
A screen indicating Complete ! appears, and the data is saved.
If you decide to cancel, press the [EXIT] button.
NOTE
NEVER turn the power off while you are saving settings.
Editing Sounds
J
27