Casio 3444 Operation Manual page 5

Note
• For information about selecting a Home City and confi guring the DST setting, see "Confi guring
Home City Settings" (page E-28).
• While the 12-hour format is selected for timekeeping, a P (PM) indicator will appear for times from
noon to 11:59 p.m. No indicator appears for times from midnight to 11:59 a.m. With 24-hour format,
time is displayed from 0:00 to 23:59, without any P (PM) indicator.
• The watch's built-in full automatic calendar makes allowances for different month lengths and leap
years. Once you set the date, there should be no reason to change it except after you have the
watch's rechargeable battery replaced or after power drops to Level 5 (page E-10).
• The day of the week changes automatically when the date changes.
• Refer to the pages shown below for more information on Timekeeping Mode settings.
- Button operation tone on/off: "To turn the button operation tone on and off" (page E-96)
- Illumination duration setting: "To change the illumination duration" (page E-92)
- Enabling and disabling power saving: "To turn Power Saving on and off" (page E-97)
- Changing the temperature, barometric pressure, and altitude display units (for a city code other
than TYO): "To specify temperature, barometric pressure, and altitude display units" (page E-44)
E-32
Objective
Bearing to objective:
West
Northwest
N: North
E: East
W: West
S: South
South
Bearing angle to objective
Note
• If the four pointers (north, south, east, west) and the literal direction indication do not appear
on the display when you press C, it could mean that the watch is displaying bearing memory
information. If this happens, press E to delete the current bearing memory contents. For more
information, see "Using Bearing Memory" (page E-39).
To return to the Timekeeping Mode, press D.
•
Pressing D will return to the Timekeeping Mode even is a reading operation is in progress.
E-34
Important!
• To ensure correct direction readings by this watch, be sure to perform bidirectional calibration before
using it. The watch may produce incorrect direction readings if you do not perform bidirectional
calibration.
• Magnetic Declination Correction
With magnetic declination correction, you input a magnetic declination angle (difference between
magnetic north and true north), which allows the watch to indicate true north. You can perform this
procedure when the magnetic declination angle is indicated on the map you are using. Note that you can
input the declination angle in whole degree units only, so you may need to round off the value specifi ed
on the map. If your map indicates the declination angle as 7.4°, you should input 7°. In the case of 7.6°
input 8°, for 7.5° you can input 7° or 8°.
Precautions about bidirectional calibration
• You can use any two opposing directions for bidirectional calibration. You must, however, make sure
that they are 180 degrees opposite each other. Remember that if you perform the procedure
incorrectly, you will get wrong bearing sensor readings.
• Do not move the watch while calibration of either direction is in progress.
• You should perform bidirectional calibration in an environment that is the same as that where you plan
to be taking direction readings. If you plan to take direction readings in an open fi eld, for example,
calibrate in an open fi eld.
E-36
To perform magnetic declination correction
1. In the Digital Compass Mode, hold down E for at least two seconds.
Magnetic declination angle Magnetic declination angle
First, SET Hold will fl ash on the display. After that, CALIBRATION will
direction value (E, W, or OFF) direction value (E, W, or OFF)
scroll across the upper display. Keep E depressed until
CALIBRATION starts scrolling.
2. Press D.
• DEC 0° will appear on the display and then the current magnetic
declination angle setting will fl ash on the display.
3. Use A (East) and C (West) to change the settings.
• The following explains magnetic declination angle direction
settings.
OFF: No magnetic declination correction performed. The magnetic
declination angle with this setting is 0°.
E: When magnetic north is to the east (east declination)
Magnetic declination Magnetic declination
angle value angle value W: When magnetic north is to the west (west declination)
• You can select a value within the range of W 90° to E 90° with
these settings.
• You can turn off (OFF) magnetic declination correction by pressing
A and C at the same time.
• The illustration, for example, shows the value you should input
and the direction setting you should select when the map shows a
magnetic declination of 1° West.
4. When the setting is the way you want, press E to exit the setting
screen.
E-38
Operation Guide 3444
Bearing Indication
Meaning
315°
North pointer
Current
0°
time
East
Taking Direction Readings
The Digital Compass Mode uses a built-in direction sensor to take direction readings and display the
results. North is indicated by three graphic segments (
the bearing and the bearing angle to your objective.
• For information about what you can do to improve digital compass reading accuracy, see "Calibrating
the Bearing Sensor" (page E-35) and "Digital Compass Precautions" (page E-42).
To take a direction reading
1. Make sure the watch is in the Timekeeping Mode or any one of the sensor modes.
• The sensor modes are: Digital Compass Mode, Barometer/Thermometer Mode, and Altimeter
Mode.
2. Place the watch on a fl at surface. If you are wearing the watch, make sure that your wrist is horizontal
(in relation to the horizon).
3. Point the 12 o'clock position of the watch in the direction whose reading you want to take.
4. Press C to start.
• COMP will appear in the upper display to indicate that a digital compass operation is in progress.
About one second after you press C, pointers (three graphic segments for north, one graphic
•
segment each for south, east, and west) will appear on the display to indicate north, south, east,
and west. The bearing to your objective will also be indicated by literal indications and a bearing
angle.
Digital Compass Readings
When you press C to start digital compass reading operation, COMP will initially appear on the
•
display to indicate that a digital compass operation is in progress.
• After the fi rst reading is obtained, the watch will continue to take digital compass readings automatically
each second for up to 60 seconds. After that, the reading operation will stop automatically. - - - will be
shown for the literal direction indication and the bearing angle to your objective.
• The auto light switch is disabled during the 60 seconds that digital compass readings are being taken.
• The margin of error for the bearing angle and the literal direction indication to your objective is ±11
degrees while the watch is horizontal (in relation to the horizon). If the indicated direction is northwest
(NW) and 315 degrees, for example, the actual direction can be anywhere from 304 to 326 degrees.
• Note that taking a direction reading while the watch is not horizontal (in relation to the horizon) can
result in large direction reading error.
• You can calibrate the bearing sensor if you suspect the direction reading is incorrect.
• Any ongoing direction reading operation is paused temporarily while the watch is performing an alert
operation (daily alarm, Hourly Time Signal, countdown timer alarm) or while illumination is turned on (by
pressing L). The direction reading operation resumes for its remaining duration after the operation
that caused it to pause is fi nished.
• See "Digital Compass Precautions" (page E-42) for important information about taking direction readings.
Calibrating the Bearing Sensor
You should calibrate the bearing sensor whenever you feel that the direction readings being produced by
the watch are off. You can use any one of two different bearing sensor calibration methods: bidirectional
calibration or magnetic declination correction.
• Bidirectional Calibration
Bidirectional calibration calibrates the bearing sensor in relation to magnetic north. Use bidirectional
calibration when you want to take readings within an area exposed to magnetic force. This type of
calibration should be used if the watch becomes magnetized for any reason.
To perform bidirectional calibration
1. In the Digital Compass Mode, hold down E for at least two seconds.
First, SET Hold will fl ash on the display. After that, CALIBRATION will
scroll across the upper display. Keep E depressed until
CALIBRATION starts scrolling.
• At this time, the north pointer fl ashes at the 12 o'clock position
and the display will show -1- to indicate that the watch is ready to
calibrate the fi rst direction.
2. Place the watch on a level surface facing any direction you want, and
press C to calibrate the fi rst direction.
• - - - is shown on the display while calibration is being performed.
When calibration is successful, Turn 180° will appear on the
display and three graphic segments (
After about one second, CALIBRATION -2- will scroll across the
upper display.
If ERR-1 appears on the display, press C again to restart the
•
direction reading operation.
3. Rotate the watch 180 degrees.
4. Press C again to calibrate the second direction.
• - - - is shown on the display while calibration is being performed.
When calibration is successful, the display will show OK and then
change to the Digital Compass Mode screen.
Using Bearing Memory
Bearing Memory lets you temporarily store and display a direction
Bearing Bearing
12 o'clock position 12 o'clock position reading so you can use it as a reference as you take subsequent digital
memory memory
direction direction
compass readings. The Bearing Memory screen displays the direction
North pointer North pointer
angle value angle value
angle for the stored reading, along with a pointer that indicates the stored
reading.
When you take digital compass readings while the Bearing Memory
screen is displayed, the direction angle of the current digital compass
reading (as read from the 12 o'clock position of the watch) and the stored
Bearing Memory direction reading will both be shown.
To store a direction angle reading in Bearing Memory
1. Press C to start a digital compass reading operation (page E-33).
• This will take an initial reading and then take readings every
Direction Direction
angle of angle of second for 60 seconds.
Pointer to bearing Pointer to bearing
current current
• If a bearing memory direction angle value is already displayed, it
in bearing memory in bearing memory
reading reading
means that there is a reading already stored in Bearing Memory. If
this happens, press E to clear the Bearing Memory reading and
Bearing Memory Bearing Memory
exit the bearing memory screen before performing the above step.
Screen Screen
). The watch also displays literal indications of
E-33
E-35
) will fl ash at 6 o'clock.
E-37
E-39