Maytag MHN30PDCWW Installation Instructions Manual page 13

CODE
COIN/DEBIT OPTION
J. Cd
J. Cd Both coin and debit selected. Press the DELICATES
AND KNITS button 3 consecutive times for this
selection.
J. C_ Coins selected, debit disabled. Press the
DELICATES AND KNITS button 3 consecutive times
for this selection.
J. _d PR models factory default to J._d. Debit Card
selected, coins disabled. Press the DELICATES AND
KNITS button 3 consecutive times to change this
selection.
J. Ed Enhanced Debit is self-selected when a Generation
2 card reader is installed in the washer. The Ed
option cannot be manually selected or deselected.
g Press the WOOLENS button once to advance
to next code.
L. 00 PRICE SUPPRESSION OPTION
This option causes the customer display to show
'ADD' or 'AVAILABLE' rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected 'OFF.'
L. PS Selected 'ON.' Press the DELICATES AND KNITS
button once for this selection.
g Press the WOOLENS button once to advance
to next code.
CLEAR ESCROW OPTION
n. CE
When selected, money held in escrow for
30 minutes without further escrow or cycle activity
will be cleared.
n 00 Not Selected 'OFF'.
n CE Selected 'ON'. Press the DELICATES AND KNITS
button once for this selection.
Press the WOOLENS button once to advance
g
to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the PERM PRESS button. Factory default
of 800 rpm.
g Press the WOOLENS button once to advance
to next code.
U. 00 PENNY INCREMENT OFFSET
U. 00 This represents the penny increment price offset
used in Generation 2 (Enhanced Debit) PR models.
Choose from 0–4 pennies by pressing the PERM
PRESS button.
g Press the WOOLENS button once to advance
to next code.
A1. 00 PREWASH LENGTH
A1. 00 This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select between
2 and 7 minutes by pressing the PERM PRESS
button.
g Press the WOOLENS button once to advance
to next code.
EXPLANATION
CODE
FINAL SPIN LENGTH
A2. 03
A2. 03 This is the number of minutes of final high speed
spin. Choose from 3–8 minutes by pressing the
PERM PRESS button.
g Press the WOOLENS button once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Represents the number
of cycles in HUNDREDS
2 00 Represents the number
of cycles in ONES
This is "VIEW ONLY" and cannot be cleared.
Press the WOOLENS button once to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following
is true:
3 00 Number of dollars
in HUNDREDS
4 00 Number of dollars in ONES
5 00 Number of CENTS
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
PD Models:
Reinstall access door.
PR Models:
1. Unplug washer or disconnect power.
2. Open console, reinsert plug into AA1, close console.
3. Plug in washer or reconnect power.
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for 0
vend price without any Special Pricing set-up, and the Coin/Debit
Option must be set to "J._d". If the washer is not in failure mode,
the door must be opened to proceed. Service Access Code
contains 4 steps. Perform the following steps:
1. Press the upper left button.
2. Press the lower right button.
3. Press the upper right button.
4. Press the lower left button.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15 second delay before it can
be attempted again.
There are 3 options to exit from the Service Mode:
1. From Set-up Code 8, press button #1 for 4 seconds.
2. Wait 2 minutes without touching any buttons (without
diagnostic modes running).
3. Power down the washer, then reapply power.
EXPLANATION
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225
3 01 = $100.00
4 68 = $ 68.00
5 75 = $
TOTAL = $168.75
.75
13