Heli-Professional REVOLUTION 500E User Manual page 19

Manual xelaris 80A Brushless ESC
Trouble shooting
Trouble
After power on, motor does not work, no
sound is emitted
After power on, motor does not work, such
an alert tone is emitted:
"beep-beep-, beep-beep-,beep-beep-"
(Every "beep-beep-" has a time interval of
about 1 second)
After power on, motor does not work, such
an alert tone is emitted:
"beep-, beep-, beep- "(Every "beep-" has a
time interval of about 2 seconds)
After power on, motor does not work, such
an alert tone is emitted:
"beep-, beep-, beep-" (Every "beep-" has a
time interval of about 0.25 second)
After power on, motor does not work, a
special tone " " is emitted after 2
beep tone (beep-beep-)
The motor runs in the opposite direction
Program the ESC with your transmitter (4 Steps)
Note: Please make sure the throttle curve is set to 0 when the
throttle stick is at bottom position and 100% for the top position.
1. Enter program mode
2. Select programmable items
3. Set item's value (Programmable value)
4. Exit program mode
1. Enter program mode
1) Switch on transmitter, move throttle stick to top
position, connect the battery pack to ESC
2) Wait for 2 seconds, the motor should emit special
tone like "beep-beep-"
3) Wait for another 5 seconds, special tone like
" " should be emitted, which means
program mode is entered
3. Set item value (Programmable value):
You will hear several tones in loop. Set the value matching to a tone by moving throttle stick to top
when you hear the tone, then a special tone "
(Keeping the throttle stick at top, you will go back to Step 2 and you can select other items; or
moving the stick to bottom within 2 seconds will exit program mode directly)
Tones
"beep-"
Items 1 short tone
Brake
Battery type
Cutoff mode
Soft-Cut
Cutoff threshold
Start mode
Timing
www.heli-professional.com
Possible Reason
The connection between battery pack
and ESC is not correct
Input voltage is abnormal, too high or
too low.
Throttle signal is irregular
The throttle stick is not in the bottom
(lowest) position
Direction of the throttle channel is
reversed, so the ESC has entered the
program mode
The connection between ESC and the
motor need to be changed.
" emits, means the value is set and saved.
"beep-beep-"
2 short tones
Off On
Lipo
NiMH
Cut-Off
Low Medium
Normal Soft
Low Medium
Check the power connection.
Replace the connector.
Check the voltage of battery pack
Check the receiver and transmit-
ter
Check the cable of throttle chan-
nel
Move the throttle stick to bottom
position
Set the direction of throttle
channel correctly
Swap any two wire connections
between ESC and motor
2. Select programmable items:
After entering program mode, you will hear 8 tones in a loop with
the following sequence. If you move the throttle stick to bottom
within 3 seconds after one kind of tones, this item will be select-
ed.
1. "beep"
2. "beep-beep-
3. "beep-beep-beep-"
4. "beep-beep-beep-beep-" cutoff threshold
5. "beep-----"
6. "beep-----beep-"
7. "beep-----beep-beep-"
8. "beep-----beep-----"
"beep-beep-beep"
3 short tones
-
-
-
High
Super soft
High
Action
brake (1 short tone)
battery typ (2 short tone)
cutoff mode (3 short tone)
(4 short tone)
startup mode (1 long tone)
timing (1 long 1 short)
set all to default (1 long 2 short)
exit (2 long tone)
4. Exit program mode
There are 2 ways to exit
program mode:
1. In step 3,
special tone "
please
throttle stick to the
bottom position
within 2 seconds.
2. In step 2, after tone
"beep-----beep-----
"(ie.The item #8),
move throttle stick
to bottom within 3
seconds.
19
after
",
move