1. Manuals
  2. Brands
  3. Windsor Manuals
  4. Floor Machine
  5. MB1500
  6. Operating instructions manual

Windsor MB1500 Operating Instructions Manual

Merit 1500 high speed burnisher
Hide thumbs
Table of Contents

Advertisement

Quick Links

HIGH SPEED BURNISHER
Operating Instructions (ENG)
MODEL: MB1500
Read these instructions before using the machine
.
G
MB1500 98804 10/19/02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MB1500 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Windsor MB1500

Summary of Contents for Windsor MB1500

  • Page 1 HIGH SPEED BURNISHER Operating Instructions (ENG) MODEL: MB1500 Read these instructions before using the machine MB1500 98804 10/19/02...
  • Page 2 THIS PAGE LEFT BLANK INTENTIONALLY MB1500 98804 05/19/00...

  • Page 3: Machine Data Log/Overview

    MACHINE DATA LOG/OVERVIEW MODEL______________________________ DATE OF PURCHASE ________________ SERIAL NUMBER____________________ YOUR DEALER Name: __________________________________________________________________________________________________ Address: _______________________________________________________________________________________________ For the name and address of your dealer contact: Windsor Industries Phone Number: _________________________________________________________________________________________ MB1500 98804 05/19/00...

  • Page 4: Table Of Contents

    Handle Installation .........3-2 Operation ............3-3 Pad Driver Installation........3-4 MAINTENANCE Machine Troubleshooting ......4-1 Wiring Diagram/Notes ........4-2 GROUP PARTS LIST Motor Group...........5-1 Frame Group ..........5-3 Drive/Pad Lock Group ........5-5 Handle Group..........5-7 Wiring Group..........5-9 Suggested Spare Parts ....... 5-11 Warranty ............5-12 MB1500 98804 01/29/02...

  • Page 5: How To Use This Manual

    SERIAL NO. FROM – column indicates Parts may be ordered from authorized Windsor the first machine the part number is dealers. When placing an order for parts, the applicable to. When the machine design...

  • Page 6: Important Safety Instructions

    Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not pull/run machine over cord. Keep cord away from heated surfaces. Connect to a properly grounded outlet. See Grounding Instructions. SAVE THESE INSTRUCTIONS MB1500 98804 05/19/00...

  • Page 7: Hazard Intensity Level

    Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. MB1500 98804 05/19/00...

  • Page 8: Grounding Instructions

    Whenever the adaptor is used, it must be held in place by a metal screw. MB1500 98804 10/02/00...

  • Page 9: Technical Specifications

    Four 5” (12.7 cm) dia., 1.25” (3 cm) wide, non-marking tread Handle 1.5” (4 cm) tubular steel, adjustable, easy to use thumb activated safety lock Dimensions (L x W x H) 31.5” (80 cm) X 21.5” (54 cm) X 43.5” (111 cm) MB1500 98804 12/07/00...

  • Page 10: Handle Installation

    5. Plug motor cord into handle cord receptacle. correct operation of the handle. The spacers are positioned completely inside the pivot holes in the casting, and are held in place by tightening the bolts and washers (items 2 and 3) against the spacer. MB1500 98804 09/25/02...

  • Page 11: Operation

    66334 bracket. PIVOT PIN C L HANDLE C L LOCKING SIDE FLAT MB1500 98804 01/24/02...

  • Page 12: Pad Driver Installation

    The circuit breaker is located on the rear of the motor. Push the reset button to restart the machine. If the breaker trips again, correct the cause of overloading before proceeding. MB1500 98804 01/24/02...
  • Page 13 THIS PAGE LEFT BLANK INTENTIONALLY MB1500 98804 01/24/02...

  • Page 14: Machine Troubleshooting

    Damaged or unevenly worn Replace pad. Do not rest pad. machine on pad when not in use. Damaged pad driver. Replace. Pad does not turn but motor is Belt is loose or broken Adjust or replace belt running MB1500 98804 10/02/00...
  • Page 15 Check pad driver system for damage Check handles, switches, and knobs for damage Store with pad off the floor Check all bearings for noise Check skirt/bumpers for damage and replace as necessary Check overall performance of machine NOTES: MB1500 98804 10/19/02...

  • Page 16: Motor Group

    MOTOR GROUP MB1500 98804 09/28/00...
  • Page 17 MOTOR GROUP SERIAL NO. PART NO. DESCRIPTION NOTES: FROM 500290 LABEL, MB1500 MAIN 27892 COVER ASM, MOTOR 1.75HP 70700 SCR, M5 X .8 X 10MM PHMS BLK 53249 MOTOR, 115V 1.75 HP MOTOR COMPONENTS (NOT SHOWN) SERIAL NO. PART NO.

  • Page 18: Frame Group

    FRAME GROUP MB1500 98804 09/28/00...
  • Page 19 SCR, M8 X 20 HHMS 03116 AXLE, MAIN BURNISHER 70691 SCR, M6 X 25 HHCS 87211 WASHER, M6 FLAT 27871 CAP, EXTRUSION 14423 BUMPER, EXTRUSION 44.30 IN 70184 SCR, M8 X 25HHCS 57276 NUT, PUSH FLAT RD .51 ID MB1500 98804 09/28/00...

  • Page 20: Drive/Pad Lock Group

    DRIVE/PAD LOCK GROUP MB1500 98804 09/25/00...
  • Page 21 SCR, ¼-20 X ¾ FHCS 09133 BEARING, 20MM X 52MM 67450 RING, 52MM INTERNAL SNAP 14424 BELT, DRIVE 38 IN 09134 BEARING, 25MM X 52MM 03115 AXLE, PAD DRIVER (MM) 27913 COVER, BEARING 70719 SCR, M4 X 8MM PPHMS MB1500 98804 09/25/00...

  • Page 22: Handle Group

    HANDLE GROUP 27, 11, 12 MB1500 98804 01/24/02...
  • Page 23 HOUSING, POLISHER HANDLE FRONT 70687 SCR, M6 X 50 SHCS BLK 38292 HANDLE, BURNISHER 730021 SPACER, POLISHER HANDLE 23207 CORDSET, 14/3 X 48 IN, SJT, BLACK 730012 STRAIN RELIEF, 14/3 STRAIGHT 70701 SCR, M10 X 1.5 X 90 HHCS PLTD MB1500 98804 09/28/00...

  • Page 24: Wiring Group

    WIRING GROUP MB1500 98804 09/25/00...
  • Page 25 CORD SET, 14/3 STO X 50' YLW 57069 NUT, ORG WIRE (2-5 18G/2-14G) 87208 WASHER, M5 SHAKEPROOF PLTD 70689 SCR, M4.8 X 10 HHTF TYPE B 23207 CORDSET, 14/3 X 48", SJT, BLK 20005 CLAMP, 5/16 NYLON MB1500 98804 09/25/00 5-10...

  • Page 26: Suggested Spare Parts

    NUT, PUSH FLAT RD .51 RD 67449 RING, 20M EXTERNAL SNAP 66337 PAD DRIVER, 20IN BURNISHER 51353 LOCK, PAD DRIVER BLUE 09133 BEARING, 20MM X 52MM 14424 BELT, DRIVE 38 IN 09134 BEARING, 25MM X 52MM 27913 COVER, BEARING 5-11 MB1500 98804 05/07/02...

  • Page 27: Warranty

    The Machine Registration Card must be completed and returned immediately at the time of purchase. If proof of purchase cannot be identified, the warranty start date is 90 days after the date of sale to an authorized Windsor distributor. Parts replaced or repaired under warranty are guaranteed for the remainder of the original warranty period.
  • Page 28 If difficulty develops during the warranty period, contact the authorized Windsor agent from whom the product was purchased. Windsor Industries, Inc. may elect to require the return of components to validate a claim. Any defective part to be returned must be shipped freight prepaid to an authorized Windsor Distributor/Service Center or to the Windsor factory.

Table of Contents