Sony BVM-F250A Operation Manual page 30

See "Available Signal Systems" and
"Available Signal Formats" on the
Operation Manual.
Parallel remote D-sub 9-pin (female) (×1)
Serial remote (LAN)
Ethernet (10BASE-T/100BASE-TX),
RJ-45 (×1)
Output
SDI BNC (×1) (monitor output)
Output signal amplitude:
800 mVp-p±10%
Output impedance: 75 ohms unbalanced
Transmission distance
3G-SDI: 70 m max.
HD-SDI: 100 m max.
SD-SDI: 200 m max.
Note
The signal from the monitor output
connector does not satisfy the ON-LINE
signal specifications.
3) When using the 5C-FB coaxial cable made by
Fujikura Ltd. or equivalent
4) When using the 5C-2V coaxial cable made by
Fujikura Ltd. or equivalent
DC 5V OUT Circle 4-pin (female) (×1)
General
Power requirements
100 V to 240 V AC,
1.2 A to 0.7 A, 50/60 Hz
24 V to 28 V DC,
4.5 A to 3.9 A
Power consumption
Approx. 110 W (AC power supply)/
approx. 100 W (DC power supply)
(maximum)
Approx. 60 W (AC power supply)/
approx. 60 W (DC power supply)
(average power consumption in the
default status)
Inrush current (1) Maximum possible inrush current at
initial switch-on (Voltage changes
caused by manual switching):
55 A peak, 15 A r.m.s. (240V AC)
(2) Inrush current after a mains
interruption of five seconds (Voltage
changes caused at zero-crossing):
36 A peak, 7 A r.m.s. (240V AC)
Operating temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended: 20 °C to 30 °C (68 °F to
86 °F)
Operating humidity
0% to 90% (no condensation)
30
Specifications (BVM-F170A)
Storage/transport temperature
Storage/transport humidity
Operating/storage/transport pressure
Mass
Supplied accessories
Optional accessories
3)
3)
4)
Design and specifications are subject to change without
\
notice.
–20 °C to +60 °C (–4 °F to +140 °F)
0% to 90%
700 hPa to 1060 hPa
Approx. 8.6 kg (18 lb 15 oz)
AC power cord (1)
AC plug holder (1)
Rack mount bracket (Left, right, each 1)
Rack mount attachment screws (4)
Operation Guide (this manual) (1)
CD-ROM (1)
BKM-16R Monitor Control Unit
BKM-39H Controller Attachment Stand
SMF-700 Monitor Interface Cable
BKM-220D SDI 4:2:2 Input Adaptor
(with serial number 2100001 or
higher)
BKM-227W NTSC/PAL Input Adaptor
(with serial number 2100001 or
higher)
BKM-229X Analog Component Input
Adaptor (with serial number 2200001
or higher)
BKM-243HS HD/D1-SDI Input Adaptor
(with serial number 2108355 or
higher)
BKM-244CC HD/SD-SDI Closed
Caption Adaptor
BKM-250TG 3G/HD/SD-SDI Input
Adaptor (with serial number 7300001
or higher)
Note
An input adaptor with a specified serial
number may be required for your
intended use.
For the serial numbers of the input
adaptors available for this unit, see "Input
Adaptors" on the Operation Manual.