Sony BVM-F250A Operation Manual page 27

R
G
B
Warm-up time Approx. 30 minutes
Input
SDI BNC (×2)
Input impedance: 75 ohms unbalanced
Signal format
See "Available Signal Systems" and
"Available Signal Formats" on the
Operation Manual.
Sampling frequency
3G-SDI:
Y/Cb/Cr (4:2:2)
148.5MHz/74.25MHz/74.25MHz
Y/Cb/Cr (4:4:4)
148.5MHz/148.5MHz/148.5MHz
G/B/R (4:4:4)
148.5MHz/148.5MHz/148.5MHz
HD-SDI:
Y/Cb/Cr (4:2:2)
74.25MHz/37.125MHz/37.125MHz
SD-SDI:
Y/Cb/Cr (4:2:2)
13.5MHz/6.75MHz/6.75MHz
Quantization
3G-SDI: 10 bit/sample, 12 bit/sample
HD-SDI: 10 bit/sample
SD-SDI: 10 bit/sample
HDMI HDMI (×1)
HDCP correspondence, Deep Color
correspondence
Signal format
See "HDMI/DisplayPort" of
"Available Signal Formats" on the
Operation Manual.
DisplayPort DisplayPort connector (×1)
HDCP correspondence, 18/24/30bpp
(bits per pixel) correspondence
Signal format
See "HDMI/DisplayPort" of
"Available Signal Formats" on the
Operation Manual.
Option port Four (4) ports
Signal format
See "Available Signal Systems" and
"Available Signal Formats" on the
Operation Manual.
Parallel remote D-sub 9-pin (female) (×1)
Serial remote (LAN)
Ethernet (10BASE-T/100BASE-TX),
RJ-45 (×1)
x y
0.681 0.319
0.189 0.724
0.141 0.051
(Typical)
Output
SDI BNC (×1) (monitor output)
Output signal amplitude:
800 mVp-p±10%
Output impedance: 75 ohms unbalanced
Transmission distance
3G-SDI: 70 m max.
HD-SDI: 100 m max.
SD-SDI: 200 m max.
Note
The signal from the monitor output
connector does not satisfy the ON-LINE
signal specifications.
3) When using the 5C-FB coaxial cable made by
Fujikura Ltd. or equivalent
4) When using the 5C-2V coaxial cable made by
Fujikura Ltd. or equivalent
DC 5V OUT Circle 4-pin (female) (×1)
General
Power requirements
100 V to 240 V AC,
1.6 A to 0.8 A, 50/60 Hz
Power consumption
Approx. 145 W (max.)
Approx. 72 W (average power
consumption in the default status)
Inrush current (1) Maximum possible inrush current at
initial switch-on (Voltage changes
caused by manual switching):
53 A peak, 17 A r.m.s. (240V AC)
(2) Inrush current after a mains
interruption of five seconds (Voltage
changes caused at zero-crossing):
39 A peak, 6 A r.m.s. (240V AC)
Operating temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended: 20 °C to 30 °C (68 °F to
86 °F)
Operating humidity
0% to 90% (no condensation)
Storage/transport temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Storage/transport humidity
0% to 90%
Operating/storage/transport pressure
700 hPa to 1060 hPa
Mass Approx. 13.0 kg (28 lb 11 oz)
Supplied accessories
AC power cord (1)
AC plug holder (1)
Operation Guide (this manual) (1)
CD-ROM (1)
3)
3)
4)
27
Specifications (BVM-F250A)