Introduction Safety Precautions Thank you for purchasing SEA&SEA products. Please read this instruction manual carefully prior to using this product. For safe handling of the product, please read the following precautions Only with a thorough understanding of this manual’s content will you carefully before use.
Safety Precautions Precautions on Handling the O-ring Do not rest heavy weight on the product. It might deform the outer casing, damage This product is kept watertight by the O-ring. To keep the O-ring functioning internal parts, make the waterproofing fail, or result in fire or electric shock. properly, please observe the following.
Precautions on Handling the O-ring Identification of Parts Coat with silicone grease Exposure mode / Formatting memory cards button Silicone grease protects the O-ring from Fiber-optic cable socket Exposure chafing. After checking the O-ring to make compensation button Accessory shoe sure that there are no scratches, dust, or Power switch Flash pop-up button...
Identification of Parts Preparation for Setting Up Front case This product must be used in combination with the optional equipment (digital camera, port, strobe, accessories etc.) for underwater photography. In order to set up the equipment, prepare each item correctly. Quick shoe Prepare the housing and port Maintaining the O-ring...
Opening and Closing the Housing Opening and Closing the Housing Closing the locking latches Opening and closing the housing is done with the locking latches. Here we will explain how to open and close the locking latches. Attach the L-hook to the front case Opening the locking latches L-hook...
Attaching and Detaching the Port Attaching and Detaching the Port Detaching the port In order to use this product underwater, the optional port for the camera lens must be attached to this product. Set the port lock to the OPEN position CAUTION Hold the front case firmly and rotate the port in a counterclockwise Only the optional ports designed for SEA&SEA digital SLR camera housings...
Mounting the camera in the Housing Mounting the Camera in the Housing Align the quick shoe with CAUTION the quick shoe base, and Make sure to release the camera's focus selector lock. slide the camera fully Remove the strap or the LCD monitor cover from the camera, if any of these forward into the front case accessories are attached.
Mounting the Camera in the Housing Connecting the Strobe Removing the camera from the housing Connect the strobe with the fiber-optic cable (option) when the strobe is triggered by sensing the light from the camera's built-in flash. Open the locking latches Remove the rear case Remove the fiber-optic cable Fiber-optic cable socket cap...
External Controls External Controls When shooting without a focus / Zoom gear Power switch Power switch Shallow groove Pull the focus / zoom dial out and rotate By rotating the knob as shown, you can turn it so that the convex part of the dial is set the power ON/OFF and operate the illumina- in the shallow groove on the spacer.
External Controls Attaching the Optional Accessories Main command dial This product accepts SEA&SEA optional accessories. By using this product in combination with those accessories, you will be able to try Rotate the dials while pressing them in various shooting techniques. to operate them.
Page 12
Attaching the Optional Accessories Attaching the Optional Accessories Finder For Sea Arm VII system This product comes equipped with a 0.5x pick-up finder. The finder can smaller Hex wrench be replaced with an optional finder so you can change the finder magnifi- The Sea Arm VII system can be cation to match your shooting conditions.
Attaching the Optional Accessories Maintenance and Storage Accessory shoe CAUTION Strobes / lights can be mounted to the accessory shoe by using optional Never use chemicals, cosmetics, any petroleum solvents such as paint thinner, or neutral detergent on the product. They may deform and damage the product. Mini Shoe Arm (29511) or Hot Shoe Arm (29501) or SA8 Ball Base for Accessory Shoe (...
Page 15
SEA&SEA SUNPAK Co., Ltd. シーアンドシー・サンパック株式会社 1-4-6, Kitasenzoku, Ohta-ku, 〒145-0062 東京都大田区北千束1-4-6 Tokyo, Japan 145-0062 TEL.03-5701-5533 TEL. +81-3-5701-5533 カスタマーサービスセンター World Customer Service Center TEL.048-255-8512 TEL. +81-48-255-8512 http://www.seaandsea.jp http://www.seaandsea.co.jp 1203-Z-01A (2012年6月現在 / Current as of Jun.2012)