Table of Contents
Advertisement
Quick Links
- 1 Jetmaster Universal - General Installation Instructions
- 2 Summary of Minimum Jetmaster Installation Specs
- 3 Open Wood Jetmaster - Minimum Flue Height
- 4 Open Gas Jetmaster
- 5 Open Gas Fireplace - Minimum Flue Height
- 6 Open Gas Jetmaster
- Download this manual
See also:
Instruction and Installation Manual
Advertisement
Table of Contents
Related Manuals for Jetmaster UNIVERSAL
Summary of Contents for Jetmaster UNIVERSAL
- Page 1 GENERAL INSTALLATION & OPERATION INSTRUCTIONS JETMASTER (VIC) PTY LTD ACN 005 872 159 ABN13 659 821 337 444 Swan St. Richmond VIC 3121 PO Box 5051 Burnley 3121 Phone: (03) 9429 5573 Fax: (03) 9427 0031 Website: www.jetmaster.com.au Email: info@jetmastervic.com.au...
-
Page 2: Table Of Contents
• Bolt gather to unit; Operating and Maintenance Instructions - For wood burning Jetmaster ..19 - 20 • Insulate entire unit and gather where painted red; • Bolt Lintel (optional) to unit - insulate between unit and Lintel;... -
Page 3: Summary Of Minimum Jetmaster Installation Specs
Summary of Minimum Jetmaster Installation Specs Summary of Minimum Jetmaster Installation Specs 1. HEARTH 2. FLUE Must be constructed from a non combustible material such as concrete, brick, or autoclaved • Single skin flue (stainless steel) must be enclosed with single skin brickwork, aerated lightweight concrete block. -
Page 4: Jetmaster Installation Into An Existing Fireplace
Any cracks or cavities in the recess must be repaired and sealed. materials & any other Step 4. Tape the insulation to the back and sides of the Jetmaster, and slide it into combustible place. materials Note 1. Do not recess unit by more than 110mm. -
Page 5: Construction Specifications - Jetmaster Traditional Victorian
Construction Specifications - Jetmaster Traditional Victorian Construction Specifications - Jetmaster Brick Veneer Installation FREE ROTATING COWL FREE ROTATING COWL... -
Page 6: Construction Specifications - Jetmaster Installation Using Hebel
Construction Specifications - Jetmaster Installation Using Hebel Construction Specifications - Jetmaster Traditional Space Saver... -
Page 7: Construction Specifications - Jetmaster Traditional Edwardian On Stud Wall
Construction Specifications - Jetmaster Traditional Edwardian On Stud Wall Construction Specifications - Jetmaster Free Standing Metal Casing “A” Typical installation with exposed “flue” and or one length heat shield, refer to decro mesh diagram for firebox and flue clearances to combustibles. -
Page 8: Construction Specifications - Jetmaster Free Standing Metal Casing "B
Construction Specifications - Jetmaster Free Standing Metal Casing “B” Construction Specifications - Jetmaster Double Sided “A” Typical installation with decro mesh heat shield to ceiling. FIREBOX AND FLUE CLEARANCES TO COMBUSTABLES Jetmaster 600, 700S,700D & 850 Freestanding Flue Pipe Flue Pipe with 900... -
Page 9: Open Gas Jetmaster
• After installing the appliance, check that the chimney/flue system draws well. 430mm • Jetmaster recommends that all gas fires be serviced every 2 years. • All gas units must be fitted by a licensed gas fitter. • It is the responsibility of the gas fitter to follow the regulations set out in the Gas Code that dictate the procedures to follow when installing a gas appliance, particularly regarding gas pipe sizing and checking of pressures. -
Page 10: Open Gas Fireplace - Minimum Flue Height
OPEN GAS FIREPLACE - Minimum Flue Height OPEN GAS JETMASTER Flue Termination HOW TO SET GAS PRESSURES 1 metre min. The Flue Terminal shall be located so that wind from any direction is not PRESSURE ADJUSTMENT FOR CAMPFYRE LOG likely to create a downdraught in the... -
Page 11: Open Gas Jetmaster
CLEANING Existing Consumer Piping Systems 1. The Jetmaster Log Pan is designed to give greater heat and fuel efficiency. For the When an additional appliance is to be connected to an existing consumer piping duration of the cold season the Log Pan should never be emptied. The resulting... -
Page 12: How To Fit Fascias
1. Use lugs and bolts provided and attach to flange on firebox. General Maintenance The visible parts of your Jetmaster can be cleaned with a damp cloth or soft brush. Should you wish you could repaint the unit with a heat resistant paint.