Sanyo SFX-11 Service Manual page 38

ii
——
_.-— —
W No. S=ING ITEM
'----------- .7 . . . . . .
CONTENTS
SEITINC:NO.
FACT. SET
EXPfANATION
———. ——— .——
-69 TCF check interva;- V29
.-
V27
'-- ---------------1
Set the time from the recognition of the train-
5ms l15ms 00
00 ing by the Modem to starting the training
60 ms 170 ms 01
check (TCF).
100ms 210ms 02
Set to correct the mismatching of between
Sanyo and other manufacturer's machine.
—— . — —.—. — .. —. — ——
— -— —.- —...-——— —— - -
70
F;K check before OFF
I 00
When this unit can not receive the high speed
phase C ON
01 01
training signal by the echo of CFR (E-52), set to
off (SETTING
No. 00).
—---——
Allowance of
—
71
5%
00 '---
When receiving consecutive error lines
Error lines
6V0
01
exceeding the setting number, this unit moves
794
02
to the sequence of bad copy quality and send
8%
03
RTN to transmitter.
Wo
04
When the E-30 occurs frequently, set the
10-30?"0 05-25 05(1 0?!0)
number to higher value but printing quality is
getting worse.
_.—
72 Continuous
3 lines 00
Error line (STD)
4 lines 01
5 lines
02
6-23
lines 03-20 03
73 Continuous 6 lines
00
Error line
7 lines 01
8 lines
02
9-26 lines
03-20 06
—.
74 Carrier off
O sec.
00
This is to set the allowance of the carrier off
detection
0.5 sec.
01
duration.
1.0 sec. 02
If the carrier off duration is less than the setting
1.5 sec.
03
value, reception is continued.
2.0 sec.
04
2.5 sec.
05
3.0 sec.
06
06
3.5 sec.
07
4.0 sec.
08
4.5 sec.
09
5.0 sec.
10
5.5 sec. 11
6.0 sec. 12
-... .. ..—.. . — ..
. .
.- ..—-— .
———-. -— .-—. — -..——- —---- . -.———-— —— .-——--- --———-— —.
75
Tx. start speed 2400 BPS '" - 00
This is to set the training start speed of the
4800 BPS
01
MODEM.
7200 BPS 02
It is recommended that if Tx. error occurs
9600 BPS 03
03
frequently set to 4800BPS.
-.—....— ——.—. —-.—.—- ---—-----
76 TSI '-"
Non
00
This is" to"set the condition of transmitting TSI.
Tx. Always
01
Tx. only when 02 01
CSI receives
——
77 DCS timing
1st DIS 00 00
This is to set the responce of DCS cor-
2nd DIS
01
responding to DIS.
In order to consider the influence of the echo
while transmitting to overseas fax. 2nd DIS
(SEITING No. 01) mightbe effective.
---- ..———
78
——. ———.. —.—
Intervalbetween " 75 msec 00 00 This is to set the interval between DCS and
DCS and Training
0.3 sec. 01
training, for the purpose of correcting the
0.5 sec. 02
mismatching of between Sanyo and othel
manufacturers machine. CCllT recommenda-
tion is 75 *20 ms.
9C
—au—