General Power Tool Safety Warnings; Save All Warnings And Instructions For Future Reference - Makita HR3200C Instruction Manual

Vibration
The vibration total
determined according to EN60745-2-6:
Work mode : chiseling function
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete, 16 mm
diameter and 100 mm depth
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : drilling into metal
Vibration emission (a
For Model HR3210FCT
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745-2-6:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745-2-6:
Work mode : chiseling function
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete, 16 mm
diameter and 100 mm depth
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : drilling into metal
Vibration emission (a
EC-DECLARATION OF CONFORMITY
Model; HR3200C,HR3210C,HR3210FCT
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 2004/108/EC, 98/37/EC.
000230
Tomoyasu Kato
Responsible Manufacturer:
value (tri-axial vector
2
) : 7.5 m/s
h,CHeq
2
2
) : 10 m/s
h,HD
2
2
) : 2.5 m/s or less
h,D
) : 88 dB(A)
pA
) : 99 dB(A)
WA
value (tri-axial vector
2
) : 8 m/s
h,CHeq
2
2
) : 10 m/s
h,HD
2
2
) : 2.5 m/s or less
h,D
CE2007
Director
ENG215-1
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
sum)
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
ENG303-1
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
ENG302-1
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
ENG102-1
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
ENG215-1
operating a power tool. Distractions can cause
you to lose control.
sum)
Electrical Safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
ENG303-1
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
ENG302-1
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
ENH101-8
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal Safety
3
GEA005-1