Advertisement
Quick Links
Cordless Driver Drill
No load
speed
Variable Speed, Reversible
MODEL 6070D
MODEL 6070DW
With
3
Hour Charger
weight
I
Net
Dimensions
(L x W x
H)
INSTRUCTION MANUAL
SPECIFICATIONS
-
Model 6070D With Reversinq Switch & Battery
10 mm
4.5 mm
x
20 mm
211 m m x 4 9 m m x 1 9 2 m m
1.0kg
(318")
I
(3116 x 314")
I
- 6oo
I
(8-114"
x
1-718"
x
7-112")
I
(2.2
Ibs)
I
I
I
I
-
Model DC7020 3 Hour Charger
I
I
3 Hr.
A.C. only
50 Hi!-6OHz
I
DC 7.2v'
I
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
Advertisement
Related Manuals for Makita 6070D
Summary of Contents for Makita 6070D
- Page 1 Cordless Driver Drill INSTRUCTION MANUAL SPECIFICATIONS Model 6070D With Reversinq Switch & Battery 10 mm 4.5 mm 20 mm (318") (3116 x 314") Model DC7020 3 Hour Charger A.C. only DC 7.2v' 50 Hi!-6OHz Manufacturer reserves the right to change specifications without notice.
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only exten- sion cords intended for use outdoors and 17.
- Page 4 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and CAUTION To reduce risk of injury, charge only MAKITA type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow.
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. - Page 6 Charging Uncap the charging connector hole. Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes CAUTION: The battery in your new tool is not fully charged. You will need to charge it before use.
- Page 7 Installing or removing driver bit CAUTION : When installing or removing the bit, be careful not to touch the trigger switch. install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise.
- Page 8 Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. CAUTION: Always check the direction of rotation before operation. Use the reversing switch only when the tool comes to a complete stop.
- Page 9 Bubble level This tool is equipped with a bubble level to aid in holding the tool horizontally. Simply center the bubble in the sight window. Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed grad- ually.
- Page 10 Storage of driver bit When not using the driver bit, return it to the storage cavity on the bottom of the tool. Drilling operation Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw.
- Page 11 CAUTION: Pressing excessively on the tool will not speed up the drilling. In fact, this excessive serve to will pressure only shorten the service life of the tool. There is a tremendous force exerted on the toolibit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece.
-
Page 12: Maintenance
Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replace- ment parts. - Page 13 ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner...
- Page 14 10 mm ( 3 / 8 ) CORDLESS DRIVER DRILL Model 6070D Note The switch and other part configuratlons from may differ country to country...
- Page 15 370D ITEM DESCRIPTION Drill Chuck S10 Pan Head Screw M5xl8 Gear Plane BearlnQ Molor Holder 6 Switch Housing R Bubble Level Tapping Screw 3x20 Note 1 ch and olher pan Specifications may diner from country to country & ",' , " DESCRIPTION Intel Resistance...
- Page 16 MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.