A.C. 1 1 5 V Note: Specifications may differ from country t o country. Makita battery 122 is a lead-acid battery. Be sure to follow the following instructions 1) Always charge it immediately after purchase. Always recharge it after use.
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don’t carry tool Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and 17.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY & CHARGER SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size Do not operate charger with damaged cord or plug mediately. Do not operate charger i f it has received a sharp blow, been dropped, or otherwise damaged in any way;...
Always charge the 2. Always recharge the Makita battery 122 after use. Be sure t o charge the Makita battery 122 for approx. one week every six months, when not using it for long periods. If left uncharged, it may become unchargeable.
ADDITIONAL SAFETY RULES FOR CHARGER 1. The Makita charger Model DC122 is specifically designed t o charge only the Makita battery 121 or with this charger. 2. Handle the charger carefully. Do not drop or strike Never carry the charger by cord or yank it t o disconnect from receptacle.
ADDITIONAL SAFETY RULES FOR TOOL This tool is specifically designed t o drill in woods/metals or t o drive wood screws. Do not use it for other purposes. Always be sure you have Be sure no one is below when using the tool in high locations. Always secure small workpieces in a vise or similar hold-down device.
If the light does not come on within five minutes after you start the charging, the battery may be unchargeable. Ship or take the charger and the battery to your nearest Makita Service Center or Distributor for checking.
Installing or removing drill bit CAUTION : Always be sure that the tool i s switched off and the batterv is disconnected from the tool before installing or removing the bit. To install the bit, place it in the chuck as it will go.
Connecting the battery to the tool Connect the battery to the tool using the adaptor cord. To prevent the adaptor cord from being accidentally disconnected, hook the cord to the strain relief hook on the battery. Carrying the battery Hook the battery to your waist belt. I f the adaptor cord is too long for your work, use the band provided to hold shorter.
Screwdriving operation of the Place point driver the tool slowly and then increase the speed gradually. Release the switch trigger just the screw bottoms out. The electric brake will then stop the tool immediately, preventing screw and/or from being damaged. When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece.
ACCESS0 CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present The accessories or attachments should be used only in the proper and intended manner.
Dec -19-’94 (3/8”) BATTERY-POWERED DRIVER DRILL Model 601D Note: The switch and other part configurations may differ from country t o country.
Motor I 0 . C . Plane Bsarlng 5 Gear Complete Drill Chuck S 1 0 Plane Besrlng 4 Gear COmplete 1 1 - 4 6 Plane Beering 4 Holder Tapping Screw 3x 1 0 Makita Label Housing Set IWith Item 31...
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.