Dell PowerEdge 6850 System Installation Manual page 29

Drive not ready
Embedded RAID error
Embedded RAID firmware is not present
Error: Incorrect memory configuration. Ensure
memory in slots DIMM_1A and DIMM_1B, DIMM_2A
and DIMM_2B on each memory card match
identically in size, speed, and rank.
Error: Incorrect memory configuration. When
mixing Dual and Single Rank memory on the same
memory card, Dual Rank DIMMs must be in slots
DIMM_1A and DIMM_1B, and Single Rank DIMMs must
be in slots DIMM2_A and DIMM2_B.
Error: Incorrect memory configuration. Memory
cards with DIMMs must be populated in order:
MEM A, MEM B, MEM C, then MEM D.
Error: More than one RAC detected, system
halted.
Error: Remote Access Card initialization
failure.
Error 8602: Auxiliary device failure. Verify
that the keyboard and mouse are securely
attached to correct connectors.
Gate A20 failure
General failure
Keyboard controller failure
Keyboard data line failure
Keyboard failure
Keyboard stuck key failure
Keyboard fuse has failed.
Manufacturing mode detected
Memory address line failure at address, read
value expecting value
Memory double word logic failure at address,
read value expecting value
Memory odd/even logic failure at start address
to end address
Memory write/read failure at address, read
value expecting value
Memory mirroring enabled
Memory tests terminated by keystroke
No boot device available
No boot sector on hard-disk drive
No timer tick interrupt
Not a boot diskette
PCI BIOS failed to install
Diskette missing or Reinsert or replace the diskette.
improperly inserted in
diskette drive.
An error has been Update the RAID firmware using the Dell Support website at
generated by the firmware support.dell.com.
used by the optional
integrated RAID controller.
The firmware used by the Restore the RAID firmware using the Dell Support website at
optional integrated RAID support.dell.com.
controller is not responding
to system requests.
One or more unmatched Ensure that the memory modules are installed in matched pairs. See
pairs of memory modules "General Memory Module Installation
are detected Components."
Dual-rank memory modules Ensure that only single-rank memory modules are installed in slots
are installed in slots DIMM2_A and DIMM2_B. See
DIMM2_A and DIMM2_B. Guidelines" in "Installing System Components."
Memory riser cards must be Move memory riser cards so they are installed in order. See
installed in consecutive Memory" in "Installing System Components."
order.
Two RACs are installed, or Ensure that only one RAC is installed. Ensure that the RAC is properly
faulty or improperly installed. See
installed RAC. Your System."
Faulty or improperly Ensure that the RAC is properly installed. See
installed RAC. Expansion
Loose or improperly Replace the mouse. If the problem persists, replace the keyboard.
connected mouse or
keyboard cable; faulty
mouse or keyboard.
Faulty keyboard controller See
(faulty system board).
Operating system Reinstall the operating system.
corrupted or improperly
installed.
Faulty keyboard controller See
(faulty system board).
Loose or improperly Ensure that the keyboard is properly connected. If the problem persists,
connected keyboard cable; replace the keyboard. If the problem persists, see
faulty keyboard; faulty
keyboard controller.
Keyboard fuse has failed. Replace the keyboard.
Faulty system board. See
System is incorrectly After the message appears during system boot, press <Alt><F> to turn
configured. off manufacturing mode.
Faulty or improperly Ensure that all memory modules are properly installed. See
installed memory modules, "Troubleshooting System
or faulty system board. the problem persists, see
Memory mirroring enabled You can enable memory mirroring using the System Setup program if the
memory is configured to support mirroring. For more information, see
"General Memory Module Installation
Components," and "Using the System Setup Program" in your User's
Guide.
The spacebar was pressed Information only.
during POST to terminate
the memory test.
Faulty or missing diskette Check the Integrated Devices configuration settings in the System
drive, optical drive, or hard Setup program. See "Using the System Setup Program" in your User's
drive. Guide. Ensure that either SCSI Controller, Diskette Controller, or IDE
CD-ROM Controller is enabled. If the system is booting from a SCSI
controller, ensure that the controller is properly connected. If the
problem persists, replace the drive. See
An operating system is not Check the hard-drive configuration settings in the System Setup
on the hard drive. program. See "Using the System Setup Program" in your User's Guide.
Faulty system board. See
Not a bootable diskette. Use a bootable diskette.
Loose cables to expansion Ensure that all appropriate cables are securely connected to the
card(s); faulty or improperly expansion cards. See
Guidelines" in "Installing System
"General Memory Module Installation
"Troubleshooting Expansion
Cards" in "Troubleshooting Your System."
"Getting Help."
"Getting Help"
"Getting Help."
Memory" in "Troubleshooting Your System." If
"Getting Help."
Guidelines" in "Installing System
"Getting Help."
"Troubleshooting Expansion
"System
Cards" in "Troubleshooting
"Troubleshooting
"Getting Help."
"Installing Drives."
Cards," in