Download  Print this page

Fujitsu E22 Touch Operating Manual

Hide thumbs

Advertisement

Quick Links

Operating Manual
Display
FUJITSU Display E22 Touch

Advertisement

loading

  Summary of Contents for Fujitsu E22 Touch

  • Page 1 Operating Manual Display FUJITSU Display E22 Touch...
  • Page 2 For driver updates, please go to: http://support.ts.fujitsu.com/download Should you have any technical questions, please contact: ● our Hotline/Service Desk (see Service Desk list or visit: http://support.ts.fujitsu.com/contact/servicedesk) ● your sales partner ● your sales office We hope you enjoy working with your new Fujitsu system!
  • Page 4 Published by / Contact address in the EU Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 Munich, Germany http://www.fujitsu.com/fts/ Copyright © Fujitsu Technology Solutions GmbH 2014. All rights reserved. Publication Date 08/2014 Order No.: A26361-K1544-Z320-1-8N19, edition 1...
  • Page 5: Table Of Contents

    FUJITSU Display E22 Touch Operating Manual For your safety Before you operate the monitor Installation instructions Operating instructions Technical support (FAQ) Technical data...
  • Page 6 Trademarks Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited or its subsidiaries in the United States and other countries. Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation in the United States and/or other countries.
  • Page 7 Adjusting the OSD Setup ......................13 Adjusting the Extras ........................13 Technical support (FAQ) ........................14 Windows shut-down mode ......................15 Technical data........................... 16 Preset operating modes ......................17 SUB D port ..........................18 DVI-D port........................... 19 HDMI port ........................... 20 Fujitsu...
  • Page 8: For Your Safety

    It is the responsibilities of the user to correct such interference. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only. Fujitsu...
  • Page 9: Weee Declaration

    To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. 5A. ● The wall socket shall be installed near the equipment and shall be easily accessible. Fujitsu...
  • Page 10: Special Notes On Lcd Monitors

    When the screen becomes black or flashing, or cannot illuminate any more, contact your dealer or service center to replace parts. Don’t repair the screen by yourself! To avoid the risk of fire, the E22 TOUCH Monitor must only be used with the original power supply unit: ADPC1965 The supplied AC/DC power supply unit must only be used with the E22 TOUCH Monitor.
  • Page 11: Before You Operate The Monitor

    Packing list The product package should include the following items: ● LCD Monitor ● Safety Manual ● Power Supply ● Power Cord ● D-SUB Cable ● DVI Cable ● USB Cable ● Audio cable ● CD with software and documentation Fujitsu...
  • Page 12: Installation Instructions

    The display surface of the device is sensitive to pressure and scratches. Clean it only using a soft, slightly moistened cloth. The surface of the casing can be cleaned with a dry cloth. If particularly dirty, use a cloth that has been moistened in mild domestic detergent and then carefully wrung out. Fujitsu...
  • Page 13: Controls And Connectors

    Connect the AC power cable to the power supply and the wall outlet (grounded). Then connect the power supply to the monitor. ► Connect the USB cable to the monitor and the computer. USB (Downstream) D-SUB Signal input USB (Downstream) Audio Input HDMI Signal input USB (Upstream) DVI Signal input USB (Downstream) Fujitsu...
  • Page 14: Adjusting The Viewing Angle

    You are able to adjust the tilted angle from 12° to 60°. Do not touch the LCD screen when you adjust the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you adjust the angle Fujitsu...
  • Page 15: Operating Instructions

    Current setting will be saved and OSD will be turned off when the keys are not touched for a period of time (see chapter “On Screen Display”, page 10). Auto Config / SOURCE / EXIT + / Volume - / ECO MENU Power button Fujitsu...
  • Page 16: On Screen Display

    MENU / ENTER ► Press to start OSD menu or enter submenu. Power Button ► Press to switch the monitor on or off. Power Indicator Power indicator Status Blue Power On mode Orange Standby mode LED off Off mode Fujitsu...
  • Page 17: Osd Lock Function

    Press + or - again to navigate through the sub-menu. Once the desired item is highlighted, press MENU button to activate it. ► Press + or - to adjust the setting. ► To exit and save, press the EXIT button. If you would like to adjust other settings, please repeat steps 2-4. Fujitsu...
  • Page 18: Adjusting The Picture

    Adjust picture Clock to reduce Vertical-Line noise Adjust Picture Phase to reduce Horizontal-Line noise Phase H.Position Adjust the vertical position of the picture. Adjust the horizontal position of the picture. V.Position Image Ratio Wide/4:3 Select Picture wide and 4:3 Fujitsu...
  • Page 19: Adjusting The Color Temperature

    Call up the Extra setting window Input Select Select input source VGA, DVI or HDMI VGA/DVI/HDMI DDC/CI Turn ON/OFF DDC/CI Support Reset Reset the menu to default yes or no Information Show the information of the main image source Fujitsu...
  • Page 20: Technical Support (Faq)

    Check the signal-cable’s connection pins for damage Message: Your computer has been set to unsuitable display mode. ► Set the computer to display mode given in the following Input no support table in chapter “Preset operating modes”, page 17. Fujitsu...
  • Page 21: Windows Shut-Down Mode

    PHASE Adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture. PHASE and CLOCK For PHASE and CLOCK adjustment use “dot-pattern” or Win 95/98/2000/ME/XP shut-down mode pattern. Fujitsu...
  • Page 22: Technical Data

    Technical data Technical data Product Name E22 TOUCH Model Name WP2-215META Dimensions and weight (LCD Display) Visible diagonals: 54.7 cm (21.5“) 16:9 Screen size: 476.6 mm x 268.1 mm Dimensions (W x H x D) 510 mm x 344 mm x 96 mm incl.
  • Page 23: Preset Operating Modes

    640 x 480 60/75 Hz 720 x 400 70 Hz 800 x 600 60/75 Hz 1024 x 768 60/75 Hz 1280 x 720 60 Hz 1280 x 1024 60/75 Hz 1440 x 900 60 Hz 1920 x 1080 60 Hz Fujitsu...
  • Page 24: Sub D Port

    Technical data SUB D port Meaning Video input red Video input green Video input blue Ground Ground Video ground red Video ground green Video ground blue +5V (DDC) Sync. ground Ground DDC Data H. sync V. sync DDC Clock Fujitsu...
  • Page 25: Dvi-D Port

    TMDS Data 1+ TMDS Data 1/3 Shield not connected not connected +5V Power Earth Hot Plug Detect TMDS Data 0- TMDS Data 0+ TMDS Data 0/5 Shield not connected not connected TMDS Clock Shield TMDS Clock + TMDS Clock - Fujitsu...
  • Page 26: Hdmi Port

    TMDS Data 2- TMDS Data 1+ TMDS Data 1 Shield TMDS Data 1- TMDS Data 0+ TMDS Data 0 Shield TMDS Data 0- TMDS Clock++ TMDS Clock Shield TMDS Clock- not connected DDC/CEC Ground +5V Power Hot Plug Detect Fujitsu...