Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch VKC 4075
Summary of Contents for Bosch VKC 4075
- Page 1 DINION Housing Kit VKC 4075 | VKN 5085 | NKN 710xx Installation Manual...
-
Page 3: Table Of Contents
Connection - rear housing feed-through fitting Configuration and final assembly Camera Operation Configuring IP camera kits Configuring analog camera kits Closing the housing Positioning sunshield Maintenance Fuse replacement Decommissioning Technical data Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 4: Safety
Caution! To protect the device, the branch circuit protection must be secured with a maximum fuse rating of 16A. This must be in accordance with NEC 800 (CEC Section 60). 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... -
Page 5: Important Safety Instructions
Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 6: Fcc And Ices Compliance
Notice! Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. -
Page 7: Short Information
All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. More information For more information please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com http://www.boschsecurity.com/catalog_overview.htm Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 8: System Overview
Yes (power and video cable) NKN-xxxxx-10N 24 VAC DINION IP 7000 Power and BNC connectors M20 fitting (for Ethernet cable) NKN-xxxxx-20N 24 VAC DINION IP 7000 Feed-through Yes (power cable only) 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... -
Page 9: Planning Information
Cable gland, 1/2-in. NPT with locking nut Polyamide / neoprene Cable gland, M20 x 1.5 Polyamide / neoprene Analog models with rear connectors Quantity Item Material 4-pin cable connector, Female 4-pin cable connector, Male Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 10: Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all parts are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. -
Page 11: Installation
Open the cover by unlatching the three latches (1) on the side of the housing. If the optional tamper-resistant screws have been installed, use the supplied wrench to remove the screws before opening the latches. Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 12: Install Mount And Housing
AC Live (24 VAC / 230 VAC) Blue AC Neutral (24 VAC / 230 VAC) Table 5.2: Other kits Connect the video/audio/alarm/PoE cables as required. Tilt or swivel the mount where necessary. 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... -
Page 13: Pulling Cables Through Mount
See example below for BNC connection and power connections (dotted line shows cables fed from rear of housing). Use the pink string to pull all other cables through the mount (including audio and alarm cables if connected). Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 14: Connecting Cables In Housing
Lower the tray so that the holes at the side fit over the two screws of the housing. – Slide the entire assembly forward approximately 5 mm (0.2 in.) from the front of the window. – Tighten the two screws to lock the tray in place. 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... -
Page 15: Feed Cables Through The Housing Rear
Failure to correctly tighten the glands could result in water ingress. Ensure that all open holes are covered with the rubber plugs provided. Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 16: Power Connections
Strip the incoming power safety earth wire and crimp into the lug. Reattach the ground connections in the order shown: Lock washer Flat washer Input power ground lug Grounding post 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... -
Page 17: Incoming Power Wires
- L (brown) power wire - N (blue) power wire Power input grounding post AC power input terminal block connectors AC power output to camera 12 VDC power output to camera Fuse Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 18: Camera Connections
CVBS connector of a monitor. – For a permanent analog output, use the optional 0.3 m cable (NBN-MCSMB-03M) to connect to a high quality coax cable. MENU CVBS NBN-MCSMB (optional) 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... -
Page 19: Housings With Rear Connectors
Assemble the cable connector, and plug it into the power receptacle on the housing. 6.6.3 Connection - rear housing feed-through fitting Pull cables through this fitting as described in Feed cables through the housing rear, page 15. Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 20: Configuration And Final Assembly
IP cameras). Other adjustments Other minor operation adjustments are possible using the camera Menu button; these adjustments are described in the camera Operation Guide (see Bosch website for applicable camera). Configuring IP camera kits The camera normally provides an optimal picture without the need for further adjustments, however when the kit is mounted and connected, the camera field of view and focus point may need to be adjusted. -
Page 21: Configuring Analog Camera Kits
Note: Always adjust to obtain a sharp picture in both wide-angle and tele positions for both far and near focus. To adjust back focus: Open the slide door panel at the side of the camera. Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... - Page 22 Press and hold the center key (menu button) for more than 1 second until the Install menu appears. Select Lens Wizard and move cursor to the Set Back Focus Now item. Turn the back focus adjustment as required. 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems...
-
Page 23: Closing The Housing
Slide the sunshield to the desired position. It has a range of 50 mm (2 in). Tighten the screws to lock the sunshield into position. If the sunshield is not installed, seal the two screw holes with the plugs supplied. Sunshield Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609... -
Page 24: Maintenance
Housing voltage Fuse rating 24 VAC 4 A, 250 VAC 120 VAC 2 A, 250 VAC 230 VAC 2 A, 250 VAC There is a spare fuse inside the housing. 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... -
Page 25: Decommissioning
Decommissioning The unit should only be passed on together with this installation guide. Disposal - Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. -
Page 26: Technical Data
PoE (optional Power-over- 48 VDC nominal IEEE 802.3af (802.3at Type 1) Ethernet connection directly 150 mA | 175 mA current consumption to camera) 7.2 W | 8.4 W power consumption 2014.11 | 1.0 | F.01U.309.609 Installation Manual Bosch Security Systems... - Page 27 Approx. Weight 0.4 kg (0.9 lb) Mounting 2 x tapped holes Thread: 1/4-20 73.7 mm (2.9 in) center spread Camera and lens See the applicable camera and lens documentation for specifications. Bosch Security Systems Installation Manual 2014.11 | 1.0 | F.01U.309.609...
- Page 30 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven The Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2015...