Operating Modes - ADJ MEGA 64 PROFILE PLUS User Instructions

Mega 64 Profile Plus
Notice:
Be sure to follow figures two and three when making your own
DMX512
cables. Do not use the ground lug on the XLR connector. Do not con-
DMX+,DMX-,COMMON
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1
DMX512 OUT
3
3-PIN XLR
2
REMOTE
INPUT OUTPUT
CONTROL
INPUT
XLR Male Socket
1 Ground
2 Cold
3 Hot
Figure 3
POWER
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
avoids signal transmission problems
1 1
DMX512 IN
and interference. It is always advisable
3
3-PIN XLR
to connect a DMX terminal, (Resistance
2 2
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - Mega 64 Profile Plus User Manual Page 6
POWER
COMMON
DMX +
1
DMX512 IN
3
3-PIN XLR
DMX -
2
Figure 2
REMOTE
INPUT OUTPUT
SOUND CONTROL
INPUT
XLR Female Socket XLR Pin Configuration
2 Cold
1 Ground
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Some manufactures use 5-pin DMX-
3-Pin XLR Female (Out) 5-Pin XLR Male (In)
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3
Do Not Use
Do Not Use
DMX Set Up Mega 64 Profile Plus
POWER
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE but-
ton until "don" is displayed, press the UP button to display "doff". Now
the display will disappear after 10s. Press any button to turn the display
on again. Be advised though that the display will turn off automatically
after 10 seconds.
To set the display press the MODE button until "dXX" is displayed. Use
Termination reduces signal errors and
avoids signal transmission problems
1
the UP or DOWN buttons to select either:
and interference. It is always advisable
3
2 to connect a DMX terminal, (Resistance
"don" = LED display on at all times.
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
"doFF" = LED display shuts off after 10 seconds.
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display can
be read upside down.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
POWER
played. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "Stnd" is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.

Operating Modes:

The Mega 64 Profile Plus has five operating modes:
• RGB+UV Dimmer Mode - Choose one of the four colors to remain
static or adjust the intensity of each color to make your desired
color.
• Sound Active mode - There are 16 sound active modes to choose
from.
• Auto Run Mode - In Auto Run mode, you can choose 1 of 16 color
change modes, 1 of 16 color fade modes, or a combo color change &
fade mode.
• Static Color Mode - There are 64 static colors to choose from.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
RGB+UV Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When "r.XXX" is displayed you are in Red dimming mode. Press the
UP and DOWN buttons to adjust intensity.
3. When "G.XXX" is displayed you are in Green dimming mode. Press
the UP and DOWN buttons to adjust intensity.
ADJ Products, LLC - www.adj.com - Mega 64 Profile Plus User Manual Page 7
Operating Instructions
POWER