LG LND7210 series Owner's Manual page 2

Connection
Precautions Connecting Power Source
• Be sure to switch off the unit before Connect power, using one of the methods
installation and connection. listed below:
• The installation should be made by To use the power adapter
qualified service personnel or system
Connect a DC 12 V power source to the
installers.
power input terminal as shown below.
• Do not expose the power and (recommended power adapter is DC 12 V/1.5
connection cables to moisture, which A or above)
may cause damage to the unit.
Connecting Network
You can control and monitor the system
via network. With the remote control
(monitoring), you can change the system
configuration or monitor the image via
network. After the installation, check the
network settings for the remote control and
monitoring work.
NOTE:
Connect the IP camera to your network using
a standard RJ-45 network cable as shown When the connecting Alarm and Audio,
tighten the screws as shown above.
below.
To use the PoE (Power over Ethernet)
device
Connect the PoE cable to the LAN port on the
unit. You must use the "IEEE802.3af" standard
PoE device.
PoE Device
(IEEE802.3af )
Broadband
Service
Router
PoE Device
Broadband (IEEE802.3af )
Service
Installation
Mounting the camera
Follow the instructions below to surface mount the camera with supplied camera mounting
bracket.
1. Use the installation guide template to check the mounting location. Face the front of the
label toward the area of interest. Using the template as a guide, make a hole through the
ceiling.
CAUTION:
Install on a ceiling or wall where can withstand the weight of 5 times of the camera including
mounting bracket.
2. Install the camera mounting bracket to the ceiling.
Connecting Microphone
NOTE:
If the camera doesn't work properly after
and Speaker Device
connecting PoE device, please check if the
PoE device supplies enough power.
Optionally connect an active speaker and/or
external microphone with a built-in amplifier.
Connecting Alarm Device
Alarm terminals are used to connect the
alarm (relay) devices such as sensors, door
switches, etc.
ALARM IN & OUT / ALARM IN & OUT
RETURN (Sensor Input / Relay Output)
Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.
AUDIO OUT
ETHERNET
AUDIO IN
With PoE NOTE:
Keep the microphone away from the speaker
Alarm (relay)
to avoid howling.
Device
Sensor
Device
NOTE:
The Photo MOS Relay is rated for 100 mA at
20 V DC or 100 mA at 28 V AC.
3. Connect the cables to the cable jacks of the camera body.
AUDIO OUT
AUDIO IN
Using the micro SD card
card in clean. Be careful the terminal part
of the micro SD card not to dusty.
You can record your surveillance environment
• As the micro SD card is consumable, the
with the micro SD card even if the network is
micro SD card end its days and may be
disconnected condition.
not able to save data if you use it more
To insert the micro SD card than over certain times. In this case,
replace micro SD card to buy a new one.
1. Remove the Dome Cover.
2. Insert the micro SD card carefully as
shown in the following illustrations.
Make sure the micro SD card terminal
position before insert the micro SD card.
Push the back end of the micro SD card
to fix it at the last step.
NOTES:
• Do not use the power too much when
you insert the micro SD card. The micro
SD card may be damaged.
• If you insert the micro SD card in the
wrong position, the micro SD card
may be damaged or it may cause the
malfunction of the micro SD Card Slot.
• Keep the terminal part of the micro SD
4. Assemble the camera and mounting bracket after align the front part of the camera and
mounting bracket. Connect the unit by following step a and b.
Remove the micro SD card Recommended the micro SD card
specification
1. Press the back end of the micro SD card
to release the lock condition.
Maker Capacity
LG
Less than
Sandisk
32 GB
Transcend
NOTE:
Speed of reading and writing more than
10 MB/Sec. (Class 6)
2. Take the micro SD card out carefully from
the camera. It may cause a malfunction
of the micro SD card or the micro SD
card slot if you use the power too much
at lock status.
CAUTION:
• If you install the micro SD card on the
camera and remove with the micro SD
card condition indicator lights on, you
must unmount the micro SD card by
using the [System > Storage > Device
Management > Unmount] menu. The
micro SD card data is compromised or
the camera may not operate normally,
if you remove the card without use
[Unmount] function.
• LG Electronics is not responsible for
deleted data caused by user mishandling
when you insert or remove the micro
SD card.
Camera Adjustment
Adjust the rotation position of the camera.
ROTATION
NOTES:
• When you assemble the dome cover, make sure the SD card PCB position is aligned with the
LG logo.
• The camera could be damaged by adjusting Pan, Tilt by force.
• PAN: 350° / TILT: 67° / ROTATION: 355°
Block Size
(FAT 32)
32 kbyte