Safety Instructions - Reloop Digital Jockey 2 Instruction Manual

OpEratION MaNuaL
CautION! For your own safety, please read this operation manual carefully before initial operati-
on! all persons involved in the installation, setting-up, operation, maintenance and service of this
device must be appropriately qualified and observe this operation manual in detail. this product
complies with the requirements of the applicable European and national regulations. Conformity
has been proven. the respective statements and documents are deposited at the manufacturer.
Congratulations on purchasing the Digital Jockey 2. Thank you for placing your trust in our disc
jockey technology. Before operating this equipment we ask you to carefully study and observe all
instructions.
Please remove the Digital Jockey 2 from its packaging. Before initial operation please make sure
that the device has not been visibly damaged during transport. If you detect any damage to the po-
wer cable or the casing, do not operate the device and contact your specialised dealer.

SaFEtY INStruCtIONS

operation manual excludes any warranty claims. the manufacturer is not liable for any damage
to property or for personal injury caused by improper handling or non-observance of the safety
instructions.
- This device has left the factory in perfect condition. To maintain this condition and to ensure a
risk-free operation the user must observe the safety instructions and warnings contained in this
operation manual.
- For reasons of safety and certification (CE) the unauthorised conversion and/or modification of the
device is prohibited. Please note that in the event of damage caused by the manual modification to
this device any warranty claims are excluded.
- The inside of the device does not contain any parts which require maintenance, with the exception
of wear parts that can be exchanged from the outside. Only qualified staff must carry out mainte-
nance, otherwise warranty does not apply!
- The fuse must exclusively be exchanged against fuses of the same class, with the same trigger
features and nominal current rating.
- Make sure that the power will only be supplied after the device has been fully set up. Always plug
in the mains plug last. Ensure that the mains switch is in the "OFF" position when connecting the
device to power.
- Only use cables that comply with regulations. Observe that all jacks and bushes are tightened and
correctly hooked up. Refer to your dealer if you have any questions.
- Ensure that when setting up the product the mains cable is not squashed or damaged by sharp
edges.
- Prevent the mains cable from coming into contact with other cables! Exercise great care when
handling mains cables and connections. Never touch these parts with wet hands!
- Connect the power cable exclusively to appropriate shock-proof outlets. The only supply point to
be used is a supply outlet in accordance with specifications of the public supply network.
- Disconnect the device from the supply outlet when not in use and before cleaning! Be sure to hold
the mains plug by the body. Never pull the mains cord!
- Position the device on a horizontal and stable low-flame base.
- Avoid any concussions or violent impact when installing or operating the device.
- When selecting the location of installation make sure that the device is not exposed to excessive
heat, humidity, and dust. Be sure that no cables lie around openly. You will endanger your own sa-
fety and that of others!
- Do not rest any containers filled with liquid that could easily spill onto the device or in its imme-
diate vicinity. If, however, fluids should access the inside of the device, immediately disconnect
the mains plug. Have the device checked by a qualified service technician before re-use. Damage
caused by fluids inside the device is excluded from the warranty.
- Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5° C)
conditions. Keep the device away from direct exposure to the sun and heat sources such as radia-
tors, ovens, etc. (even during transport in a closed vehicle). Never cover the cooling fan or vents
- Always ensure sufficient ventilation.
- The device must not be operated after being taken from a cold environment into a warm environ-
ment. The condensation caused hereby may destroy your device. Do not switch on or operate the
device until it has reached ambient temperature!
- Controls and switches should never be treated with spray-on cleaning agents and lubricants. This
device should only be cleaned with a damp cloth. Never use solvents or cleaning fluids with a pet-
roleum base for cleaning.
- When relocating, the device should be transported in its original packaging.
12
CautION! please exercise particular caution when
handling 100-240V, 50/60Hz power voltage. this
voltage rating may lead to a critical electrical shock!
any damage caused by the non-observance of this