Timer Recordings With The Showview ® System - Loewe Centros 1172 Operating Manual

Timer recordings with the ShowView ® system
Programming timer recordings with this system
is child's play. Most television schedule publica-
tions include the SHOWVIEW code numbers along
with the information about the programmes. So
when you want to make a timer recording of a
programme, you only need to key in the appropri-
ate SHOWVIEW code number. The date, start time,
end time and station are set automatically. You
only need to set the recording quality and specify
whether it is to be a one-off or repeated recording.
You can save up to seven timer programmes on the
recorder.
1. Press the green key SV/
The "Showview" menu is displayed.
Showview
Number
0-9 Input Enter
MENU
OK OK
To close the menu, press SV again
Input fi elds
• Number – key in the SHOWVIEW code
number.
• Repeat – select the repeat type that you
require (once, daily or weekly).
2. Use the number buttons to input the SHOWVIEW
code number.
• / (left/right) – select the input fi elds.
• If you make a wrong input, press repeatedly
before you press OK to delete the
numbers one by one and then correct the
password. You can also use
straight to the input fi eld that you wish to
correct and then overwrite the numbers that
are there by using 0-9.
3. Use / to place the cursor in the "Repeat"
column. Use / to select the "Repeat" op-
tion (once, daily [Monday - Friday] or weekly).
4. When you have input all the programme's
details, press OK.
The "Timer recording" menu will appear. The
settings can be altered from here.
5. Carry out steps 3-5 on the previous page (Timer
recording).
32122 DVD Rec_Centros_GB.indb 45 32122 DVD Rec_Centros_GB.indb 45
Checking/changing the timer recording
details
You can check the programming when the DVD
recorder is switched on. Press
OK
"Timer recording list" menu is displayed.
Timer Record List
PR Date
5 10/4 Di
5 10/4 Di
.
Edit
MENU
OK OK
Repeat
Edit a timer program
Once
• Use /
wish to check.
Delete Close
END
• Press OK to go to the selected program.
.
• Press
menu, where you can make the change.
Deleting a timer program
You can deleted a timer program at any time before
recording starts.
Use / to select the entry in the timer record-
ing list that you want to delete. If you wish to
delete the recording, press
/ to go
Cancelling a timer recording
After a timer recording has begun, you can cancel
it at any time by pressing
Conditions that will prevent recording
When the timer has been programmed, the
recorder will not record under the following circum-
stances:
• No disc has been inserted.
• A non-writable disc has been inserted.
• "Disc protection" is switched on in the main
menu (see page 27).
twice. The
VPS/
Start Time Length Mode Check
PDC
19:20 30M LQ Off Rec. OK
20:15 45M HQ Off Rec. OK
Delete Timer Record
REC-MENU END Close
to select a timer recording that you
to open the "Timer recording"
.
.
• There is no electric current.
• 99 titles have already been recorded on the disc.
• The recording start time is less than 3 minutes
from the time it was programmed.
You cannot program the timer under the
following circumstances:
• A recording is already in progress.
• The start time required is in the past.
• Seven timer recordings have already been
programmed.
Multiple overlapping timer programs:
• The earlier recording takes priority.
• When the earlier recording ends, the later one
will start.
• When two recordings begin at the same time,
the fi rst to be input takes priority.
If the disc is damaged, it is possible that the
recording will not be done properly. Even if the
"Recording OK" message appears in the "Status"
fi eld, this is not necessarily true in this case.
45 -
26.04.2005 11:23:46 26.04.2005 11:23:46