Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Matrix T1xe-02(AC)
Summary of Contents for Matrix T1xe-02(AC)
- Page 1 T 1 x e - 0 2 ( A C ) T r e A d m i l l S e r V i C e m A N U A l...
-
Page 2: Table Of Contents
TAble of CoNTeNTS CHAPTer 1: SeriAl NUmber loCATioN ............1 CHAPTer 2: imPorTANT SAfeTy iNSTrUCTioNS Before Getting Started ....................2 Read and Save These Instructions ................3 Electrical Requirements ..................... 4 CHAPTer 3: PreVeNTATiVe mAiNTeNANCe Recommended Cleaning Tips ..................5 Check for Damaged Parts .................. - Page 3 TAble of CoNTeNTS 8.14 04A0 Error Troubleshooting ..................34 8.15 Troubleshooting - Heart Rate Issues ................35 8.16 Troubleshooting - TV Reception Issues ..............36 CHAPTer 9: PArT rePlACemeNT GUide Motor Cover Replacement ..................37 Rear Roller Replacement ................... 38 Deck Replacement .....................
-
Page 4: Chapter 1: Serial Number Location
CHAPTer 1: SeriAl NUmber loCATioN 1.1 SeriAl NUmber loCATioN... -
Page 5: Chapter 2: Important Safety Instructions
This treadmill is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating the Matrix Treadmill. Please leave a 78.75" (2000 mm) x 39.50" (1000 mm) landing zone behind the treadmill. This zone is to allow easy access to the treadmill and gives the user an easy exit path from the machine. -
Page 6: Read And Save These Instructions
When using an electrical product, basic precautions should always be followed including the following: • D onotusetheequipmentinanywayotherthandesignedor intended by the manufacturer. It is imperative that all Matrix Fitness System's equipment is used properly to avoid injury. dANGer: To reduce the risk of electric shock: Always unplug this equipment from the electrical outlet immediately after • Keephandsandfeetclearofmovingpartsatalltimestoavoid... -
Page 7: Electrical Requirements
All Matrix treadmills require the use of a 20 amp "dedicated circuit" with a non-looped (isolated) neutral / ground for the power requirement. Quite simply this means that each outlet you plug your treadmill into should not have anything else running on that same circuit. The easiest way to verify this is to locate the main circuit breaker box, and turn off the breaker(s) one at a time. -
Page 8: Chapter 3: Preventative Maintenance
• C leanwithsoapandwaterorothernon-ammoniabasedallpur- making adjustments or performing maintenance or repair of any pose cleaners. kind is qualified to do so. Matrix Fitness Systems will provide service and maintenance training at our corporate facility upon • W ipefootrails,console,heartrategrips,andhandlebarsclean request or in the field if proper arrangements are made. -
Page 9: Care And Maintenance Instructions
3) Remove the motor cover at the front of the machine. Start the unit and raise the incline settings to maximum height. Turn the power switch off at the front of the machine to prevent it from lowering accidentally. Lubricate the incline motor Acme screw (Matrix recommends Super Lube brand grease with PTFE additive). -
Page 10: Auto Calibration Procedure
CHAPTer 3: PreVeNTATiVe mAiNTeNANCe 3.5 AdjUSTiNG THe rUNNiNG belT 3.4 AUTo CAlibrATioN iNSTrUCTioNS Run Auto Calibration to calibrate incline after assembly and after After placing the treadmill in the position it will be used, the belt replacing any electronic component. must be checked for proper tension and centering. -
Page 11: Knowing When To Replace The Running Belt And Deck
CHAPTer 3: PreVeNTATiVe mAiNTeNANCe 3.6 kNoWiNG WHeN To rePlACe THe rUNNiNG belT ANd deCk One of the most common wear and tear items on a treadmill is the deck and belt combination. If these two items are not properly maintained, they can cause damage to other components. -
Page 12: Console Description
CHAPTer 4: CoNSole oVerlAy ANd WorkoUT deSCriPTioN 4.1 T1xe-01 CoNSole deSCriPTioN mUlTi-PUrPoSe keyS: Keys have different functions depending on each screen. Go: One touch Start and Quick Start. eNTer: To confirm each program setting. UP / doWN iNCliNe: Easy information and incline selection. UP / doWN SPeed: Easy information and speed selection. -
Page 13: Manual Workout Operation
4.3 leVel bASed WorkoUT oPerATioN Your Matrix T1xe-01 Treadmill offers a variety of level-based workouts to challenge users of all fitness levels. The following information will briefly explain the workouts and how to program the treadmill for each workout selection. -
Page 14: Target Heart Rate Control Workout Operation
4.5 GerkiN TeST WorkoUT oPerATioN Your Matrix T1xe-01 Treadmill offers a Gerkin Firefighter Protocol Fitness Test, The Gerkin Protocol was developed by Dr.. Richard Gerkin of the Phoenix (Arizona) Fire Department. It is a sub-maximal graded treadmill evaluation used by many fire departments across the United States to assess the physical condition of the firefighters. -
Page 15: Gerkin Fitness Test Workout Operation
CHAPTer 4: CoNSole oVerlAy ANd WorkoUT deSCriPTioN 4.5 GerkiN TeST WorkoUT oPerATioN - CoNTiNUed SUb mAximAl TreAdmill eVAlUATioN CArdioVASCUlAr fiTNeSS PerCeNTileS CoNVerSioN TAble males: Vo2 max (ml/kg/min) 0-29 30-39 40-49 50-59 Stage Time Converted Vo2max >58.8 >58.9 >55.4 >52.5 1:00 31.15 SUPERIOR 1:15... -
Page 16: Chapter 5: Manager Mode
CHAPTer 5: mANAGer mode 5.1 mANAGer mode oVerVieW 1) To enter Manager Mode, press "ENTER, 1, 0, 0, 1, ENTER" on the number keypad ON THE CONSOLE and Manager Mode will appear on the display. 2) Manager Mode is divided into 6 tabs. They are About, Time, Speed, Defaults, Language, and TV. 3) Choose a tab by touching the button next to the desired tab. -
Page 17: Manager Mode - About Tab
CHAPTer 5: mANAGer mode 5.2 mANAGer mode - AboUT TAb mANAGer mode fUNCTioN & defAUlTS deSCriPTioNS modified About Accumulated Distance Total distance showed in native units (miles Cannot be modified. or kilometers). Accumulated Time Total time. Cannot be modified. Software Versions Software Version, for display only. -
Page 18: Manager Mode - Speed Tab
CHAPTer 5: mANAGer mode 5.4 mANAGer mode - SPeed TAb mANAGer mode fUNCTioN & defAUlTS deSCriPTioNS modified Speed Maximum Speed Controls the maximum speed for all Maximum: 12 MPH / 20 KPH Default: 12 MPH / 19.2 KPH programs, Displayed in native units (MPH or Minimum: 3 MPH / 4.8 KPH KPH). -
Page 19: Manager Mode - Language Tab
CHAPTer 5: mANAGer mode 5.6 mANAGer mode - lANGUAGe TAb mANAGer mode fUNCTioN & defAUlTS deSCriPTioNS modified Language Select default language. This option allows the user to select a flag for a specific language. lANGUAGe flAG UNiT lANGUAGe flAG UNiT lANGUAGe flAG UNiT... -
Page 20: Manager Mode - Tv Tab
CHAPTer 5: mANAGer mode 5.7 mANAGer mode - TV TAb mANAGer mode fUNCTioN & defAUlTS deSCriPTioNS modified Default Channel This option controls the default TV channel Maximum: 99 Default: 1 on start up. Minimum: 1 Default Volume This option controls the default TV volume on Maximum: 17 Default: 1 start up. -
Page 21: Chapter 6: Engineering Mode
CHAPTer 6: eNGiNeeriNG mode 6.1 eNGiNeeriNG mode oVerVieW The Engineering Mode allows the club owner to keep track of the technical settings and error history for the treadmill. 1) To enter Engineering Mode, press ENTER, 2, 0, 0, 1, ENTER on the number keypad ON THE CONSOLE. Engineering Mode will appear on the display (Figure A). -
Page 22: Engineering Mode - Statistics
CHAPTer 6: eNGiNeeriNG mode 6.3 eNGiNeeriNG mode - STATiSTiCS TAb eNGiNeeriNG mode fUNCTioN & defAUlTS deSCriPTioNS modified Statistics This option displays the workout information history of the unit. 6.4 eNGiNeeriNG mode - errorS TAb eNGiNeeriNG mode fUNCTioN & defAUlTS deSCriPTioNS modified Errors This option displays the error... -
Page 23: Engineering Mode - Clubs
6.5 eNGiNeeriNG mode - ClUbS TAb eNGiNeeriNG mode fUNCTioN & defAUlTS deSCriPTioNS modified Clubs This option selects a screen Default: Matrix header from a list. 6.6 eNGiNeeriNG mode - ClUb id TAb eNGiNeeriNG mode fUNCTioN & defAUlTS deSCriPTioNS modified Club ID This option records the club ID of the equipment. -
Page 24: Chapter 7: Service Mode
CHAPTer 7: SerViCe mode 7.1 SerViCe mode oVerVieW The Service Mode allows an authorized service provider to test and store information on the treadmill. 1) To enter Service Mode, press ENTER, 3, 0, 0, 1, ENTER on the number keypad ON THE CONSOLE. Service Mode will appear on the dis- play (Figure A). -
Page 25: Service Mode - Setup
CHAPTer 7: SerViCe mode 7.2 SerViCe mode - SeTUP TAb SerViCe mode fUNCTioN & defAUlTS deSCriPTioNS modified Setup Machine Type This option selects the current model. Default: Treadmill Serial Number This option display the serial number of the console and frame. Accumulated Distance This option displays the total distance of workouts since production. -
Page 26: Service Mode - Log
CHAPTer 7: SerViCe mode 7.4 SerViCe mode - loG TAb SerViCe mode fUNCTioN & defAUlTS deSCriPTioNS modified This option is to record key component replacement history. 7.5 SerViCe mode - dATe & Time TAb SerViCe mode fUNCTioN & defAUlTS deSCriPTioNS modified Date &... -
Page 27: Chapter 8: Troubleshooting
CHAPTer 8: TroUbleSHooTiNG 8.1 eleCTriCAl diAGrAm... - Page 28 CHAPTer 8: TroUbleSHooTiNG 8.1 eleCTriCAl diAGrAm - CoNTiNUed diGiTAl CommUNiCATioN Wire PUlSe GriP Wire...
-
Page 29: Mcb Wiring
CHAPTer 8: TroUbleSHooTiNG 8.2 mCb WiriNG jP3 - Console Cable jP4 - incline motor Cable N - Power input (white) l - Power input (black) U - motor Wire (red) V - motor Wire (White) W - motor Wire (black) -
Page 30: Mcb Led Placement And Definitions
CHAPTer 8: TroUbleSHooTiNG 8.3 mCb led PlACemeNT ANd defiNiTioNS PWm - Console PWm signal light (when the motor is running, the light should flash). Com - digital communication light. fAUlT - The machine has stopped due to any C class error. UP / doWN (ff) - incline motor status light. -
Page 31: Error Messages On The Console
CHAPTer 8: TroUbleSHooTiNG 8.4 error meSSAGeS oN THe CoNSole ClASS error Code deSCriPTioN CoNdiTioN leVel 0140 Incline motor fail. When the incline motor is supposed to move, it does not move. When the error happens the incline motor will be locked. The command "initialize"... -
Page 32: 0140 / 01A0 Error Troubleshooting
CHAPTer 8: TroUbleSHooTiNG 8.5 0140 / 01A0 error TroUbleSHooTiNG error meSSAGe 0140 / 01A0 1) cause: a. Incline motor operation failed. 2) sOLuTION: a. Check the connection of the incline motor cable at the MCB. b. Run auto calibration (See Section 3.5). c. -
Page 33: 01A8 / 01Ad / 02B6 / 02B7 / 02B8 Error Troubleshooting
CHAPTer 8: TroUbleSHooTiNG 8.7 01A8 / 01Ad / 02b6 / 02b7 / 02b8 error TroUbleSHooTiNG error meSSAGe 01A8 / 01Ad / 02b6 / 02b7 / 02b8 1) cause: a. 01A8 - Main motor over current of 7 Amps. b. 01AD - Motor over temperature. c. -
Page 34: 02A0 / 02A8 Error Troubleshooting
CHAPTer 8: TroUbleSHooTiNG 8.9 02A0 / 02A8 error TroUbleSHooTiNG error meSSAGe 02A0 / 02A8 1) cause: a. 02A0 - Main motor failure. The belt does not move when it is supposed to move. b. 02A8 - Inverter circuit of the motor failed. Motor resistance is closed. 2) sOLuTION: a. -
Page 35: 02A1 / 02A2 Error Troubleshooting
CHAPTer 8: TroUbleSHooTiNG 8.10 02A1 / 02A2 error TroUbleSHooTiNG error meSSAGe 02A1 / 02A2 1) cause: a. 02A1 - Over AC power input voltage. b. 02A2 - Over / low DC bus voltage. 2) sOLuTION: a. Use a multi - meter to check if the input power is over 260V. b. -
Page 36: 02B5 Error Troubleshooting
CHAPTer 8: TroUbleSHooTiNG 8.12 02b5 error TroUbleSHooTiNG error meSSAGe 02b5 1) cause: a. The inverter sensor is reading the normal rated current is over 10.5 amps for 60 seconds. 2) sOLuTION: a. Use a multi - meter to check the motor cable for resistance at 3 points (Figures A, B, & C). b. -
Page 37: 02B9 / 02Ba / 02Bc / 02Bd Error Troubleshooting
CHAPTer 8: TroUbleSHooTiNG 8.13 02b9 / 02bA / 02bC / 02bd error TroUbleSHooTiNG error meSSAGe 02b9 / 02bA / 02bC / 02bd 1) cause: a. 02B9 - The inner memory IC data write error. b. 02BA - The inner memory IC data read error. c. -
Page 38: Troubleshooting - Heart Rate Issues
CHAPTer 8: TroUbleSHooTiNG 8.15 TroUbleSHooTiNG - HeArT rATe iSSUeS HeArT rATe fUNCTioN doeS NoT Work or iS reAdiNG iNCorreCTly PoSSible CAUSeS: 1) The chest strap being used is not making good contact with the user's chest. 2) The chest strap is at a low battery status. 3) The chest strap is damaged. -
Page 39: Troubleshooting - Tv Reception Issues
CHAPTer 8: TroUbleSHooTiNG 8.16 TroUbleSHooTiNG - TV reCePTioN iSSUeS No reCePTioN oN THe TV or iT iS blUrry PoSSible CAUSeS: 1) The coax signal is not being sent strongly enough for good TV reception. 2) The coax cable is pinched or installed incorrectly. 3) The TV is defective. -
Page 40: Chapter 9: Part Replacement Guide
CHAPTer 9: PArT rePlACemeNT GUide 9.1 moTor CoVer rePlACemeNT 1) Use a 6mm Allen wrench to remove the 2 screws holding the motor cover to the frame (Figures A). 2) The motor cover is velcroed to the frame, so you will have to pull up with some force (Figure B). fiGUre A fiGUre b 3) Figure C shows the motor area with the cover removed. -
Page 41: Rear Roller Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.2 reAr roller rePlACemeNT 1) Remove one of the rear end caps using a Phillips screwdriver (Figure A). 2) Use an 8mm Allen wrench to remove both roller adjustment screws (Figure B). fiGUre A fiGUre b 3) Remove the rear roller from the running belt (Figures C &... -
Page 42: Deck Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.3 rUNNiNG deCk rePlACemeNT 1) Remove the motor cover as outlined in Section 9.1. 2) Remove the four running deck screws using a 5mm Allen wrench (Figure A). fiGUre A 3) Remove the running deck from the running belt (Figures B & C). fiGUre b fiGUre C 4) Reverse Steps 1-3 to install a new running deck. -
Page 43: Deck Cushion Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.4 deCk CUSHioN rePlACemeNT 1) Remove the deck as outlined in Section 9.3. 2) Holding the bolt with a 5 mm Allen wrench, loosen the nut with a 13 mm socket (Figure A & B). fiGUre A fiGUre b 3) For the rear cushion, hold the cushion and remove the 13 mm nut (Figure C). -
Page 44: Front Roller Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.5 froNT roller rePlACemeNT 1) Remove the motor cover as outlined in Section 9.1. 2) Loosen both of the rear roller screws using an 8mm Allen Wrench to remove tension from the running belt (Figure A). fiGUre A 3) Remove the front roller mounting screws using an 8 mm Allen wrench (Figures B &... -
Page 45: Running Belt Removal
CHAPTer 9: PArT rePlACemeNT GUide 9.6 rUNNiNG belT rePlACemeNT 1) Remove the motor cover as outlined in Section 9.1. 2) Remove the rear roller as outlined in Section 9.2. 3) Remove the running deck as outlined in Section 9.3. 4) Remove the front roller as outlined in Section 9.5. 5) Remove the running belt (Figures A &... -
Page 46: Side Rail Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.7 Side rAil rePlACemeNT 1) Remove the rear end cap using a Phillips screwdriver (Figure A). 2) Loosen the four screws under the frame using a 5 mm Allen wrench (Figure B). fiGUre b fiGUre A 3) Slide the rail off the back of the treadmill (Figures C &... -
Page 47: Motor Control Board (Mcb) Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.8 moTor CoNTrol boArd (mCb) rePlACemeNT 1) Turn off power and disconnect the cord from the machine. 2) Remove the motor cover as outlined in Section 9.1. 3) Disconnect the wire connectors at the MCB. 4) Remove the 2 screws holding each side of the MCB to the frame (Figures A &... -
Page 48: Motor Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.9 moTor rePlACemeNT 1) Turn off power to the treadmill and disconnect the power cord. 2) Remove the motor cover as outlined in Section 9.1. 3) Use a hook or loop of wire to remove the spring from the drive belt tensioner (Figure A). 4) The tensioner should now pivot away from the drive belt (Figure B fiGUre b fiGUre A... - Page 49 CHAPTer 9: PArT rePlACemeNT GUide 9.9 moTor rePlACemeNT - CoNTiNUed 7) Disconnect the motor cable ground wire from the grounding post (Figure E). 8) Disconnect the motor cable from the MCB (Figure F). fiGUre f fiGUre e 9) Remove the 4 screws holding the motor to the frame (Figure G). 10) Remove the motor from the treadmill.
-
Page 50: Drive Belt Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.10 driVe belT rePlACemeNT 1) Turn off power to the treadmill and disconnect the power cord. 2) Remove the motor cover as outlined in Section 9.1. 3) Use a hook or loop of wire to remove the spring from the drive belt tensioner (Figure A). 4) The tensioner should now pivot away from the drive belt (Figure B fiGUre A fiGUre b... - Page 51 CHAPTer 9: PArT rePlACemeNT GUide 9.10 driVe belT rePlACemeNT 7) Remove the two 8 mm front roller screws (Figures E & F). fiGUre f fiGUre e 8) Lift the roller and remove the old drive belt (Figure G). fiGUre G 9) Reverse Steps 1-8 to install a new drive belt.
-
Page 52: Incline Motor Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.11 iNCliNe moTor remoVAl 1) Turn off power to the treadmill and disconnect the power cord. 2) Remove the motor cover as outlined in Section 9.1. 3) Lift the treadmill and support it so that the front wheels are off the floor, or the unit may be tipped on its side (Figure A). 4) Remove the cotter pin from the elevation rack pin (Figure B). - Page 53 CHAPTer 9: PArT rePlACemeNT GUide 9.11 iNCliNe moTor remoVAl - CoNTiNUed 7) Remove the incline motor cable ground wire from the ground prong in the motor frame (Figure E). 8) Disconnect the incline motor from the top mounting bracket (Figure F). fiGUre e fiGUre f 9) Lift the incline motor away from the treadmill (Figure G).
-
Page 54: Console Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.12 CoNSole rePlACemeNT 1) Turn off power to the treadmill and disconnect the power cord. 2) Remove the 4 screws holding the back of the console to the front (Figure A). 3) Disconnect the wire connection attached to the back to the console and remove the console back (Figure B). fiGUre A fiGUre b 3) Remove the four 6mm screws from underneath the console (Figure C). -
Page 55: Emergency Stop Switch Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.13 emerGeNCy SToP SWiTCH rePlACemeNT 1) Turn off power to the treadmill and remove the power cord. 2) Remove the console as outlined in Section 9.12. 3) Remove the 2 screws holding the red emergency stop key to the emergency stop frame (Figure A). 4) Remove the 2 screws holding the emergency stop frame to the console frame (Figure B). - Page 56 CHAPTer 9: PArT rePlACemeNT GUide 9.13 emerGeNCy SToP SWiTCH rePlACemeNT - CoNTiNUed 6) Disconnect the 2 wires plugged into the back of the emergency stop switch (Figure E). 7) Depress the tabs on the top and the bottom of the emergency stop switch (Figure F). fiGUre e fiGUre f 8) Once the tabs are depressed, the emergency stop can be removed from the emergency stop frame (Figure G).
-
Page 57: Console Frame Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.14 CoNSole frAme rePlACemeNT 1) Turn off power to the treadmill and disconnect the power cord. 2) Remove the console as outlined in Section 9.12. 3) Remove the 2 screws on each side holding the console frame to the handlebar frame (Figure A). fiGUre A 4) Remove the console frame from the handlebar frame. -
Page 58: Heart Rate Board Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.15 HeArT rATe boArd rePlACemeNT 1) Turn off power to the treadmill and remove the power cord. 2) Remove the console as outlined in Section 9.12. 3) Remove the console frame as outlined in Section 9.14. 4) Remove the 2 screws holding the emergency stop frame to the console frame (Figure A). -
Page 59: Speed Or Incline Keypad Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.16 SPeed or iNCliNe keyPAd rePlACemeNT 1) Turn off power to the treadmill and remove the power cord. 2) Remove the console as outlined in Section 9.12. 3) Remove the console frame as outlined in Section 9.14. 4) Remove the 2 screws holding the emergency stop frame to the console frame (Figure A). -
Page 60: Handlebar Frame Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.17 HANdlebAr frAme rePlACemeNT 1) Turn off power to the treadmill and remove the power cord. 2) Remove the console as outlined in Section 9.12. 3) Remove the console frame as outlined in Section 9.14. 4) Remove the 3 screws on each side holding the handlebar frame to the console mast (Figure A). -
Page 61: Heart Rate Handlebars Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.18 HeArT rATe HANdlebAr rePlACemeNT 1) Turn off power to the treadmill and remove the power cord. 2) Remove the console as outlined in Section 9.12. 3) Remove the console frame as outlined in Section 9.14. 4) Remove the 3 screws on each side holding the handlebar frame to the console mast (Figure A). -
Page 62: Heart Rate Grips Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.19 HeArT rATe GriPS rePlACemeNT 1) Turn off power to the treadmill and unplug the power cord. 2) Use a flat screwdriver to pry off the bottom heart rate grip plate (Figure A). fiGUre A 3) Unplug the bottom heart rate grip plate and remove it (Figure B). -
Page 63: Console Mast Replacement
CHAPTer 9: PArT rePlACemeNT GUide 9.20 CoNSole mAST rePlACemeNT 1) Turn off power to the treadmill and remove the power cord. 2) Remove the console as outlined in Section 9.12. 3) Remove the console frame as outlined in Section 9.14. 4) Remove the handlebar frame as outlined in Section 9.17. -
Page 64: Testing The Treadmill
CHAPTer 9: PArT rePlACemeNT GUide 9.21 TeSTiNG THe TreAdmill oNCe THe TreAdmill or rePlACemeNT PArT iS fUlly iNSTAlled ANd ASSembled ANd ProPerly PlACed oN THe floor, USe THe folloWiNG iNSTrUCTioNS To SeTUP ANd TeST THe mACHiNe: 1) If the treadmill was just assembled or if any electronic component has been replaced (including if the console cable is unplugged for any reason), the treadmill MUST be auto calibrated. -
Page 65: Chapter 10: Treadmill Specifications And Assembly Guide
0.5 - 12 mph / 0.8 - 20 km/h Contact HR Sensors Telemetric HR Receiver Transport Wheels DRIVE SYSTEM Motor Matrix 3.0 hp AC Dynamic Response Drive System™ Motor Controller Commercial Treadmill AC Drive CONSOLE Display Type 7" LCD Display Feedback Time, Distance, Calories, Calories per Hour, Speed, Incline, Pace, Heart Rate, METs, Watts, and Profile. -
Page 66: Fasteners And Assembly Tools
CHAPTer 10: TreAdmill SPeCifiCATioNS ANd ASSembly GUide 10.2 fASTeNerS ANd ASSembly ToolS frAme SeT PArT # PArT NAme diAGrAm SPeCifiCATioN qUANTiTy Color Hex Head Cap Screw M8 x 1.25P x 25L Blue Flat Washer 8.2 x 19 2.0t Blue Hex Head Cap Screw M8 x 1.25P x 15L Black Button Head Screw... -
Page 67: Assembly Instructions
Prior to assembling the treadmill, unpack all of the contents of the box and make sure that all necessary components are present. Review the contents of the hardware package for completeness. Contact Matrix customer service at 866.693.4863 to report any missing items. - Page 68 CHAPTer 10: TreAdmill SPeCifiCATioNS ANd ASSembly GUide 10.3 ASSembly iNSTrUCTioNS - CoNTiNUed Open Black & White Assembly Bag. Assemble the HR handlebar to the left and right handlebars using item 14 - hex head cap screw. Fasten the contact HR handlebar assembly to the console masts using item 15 - button head screw and item 12 - flat washer. Pull the HR wires through the handlebar using the wire pull.
- Page 69 CHAPTer 10: TreAdmill SPeCifiCATioNS ANd ASSembly GUide 10.3 ASSembly iNSTrUCTioNS - CoNTiNUed Open Black Assembly Bag. Assemble the console frame to the Open Yellow Console Assembly Bag. Make the appropriate color handlebars using item 14 - hex head cap screw. Be sure to route coded wire connections to the faceplate then assemble to the the console cables down the console mast and connect the HR console frame using item 41 - hex head cap screw.
- Page 70 CHAPTer 10: TreAdmill SPeCifiCATioNS ANd ASSembly GUide 10.3 ASSembly iNSTrUCTioNS - CoNTiNUed Open Green Assembly Bag. Install the power cord and assemble Replace the motor cover(s) and power the treadmill on. The power item 18 power cord holder with item 22 button head screw. If your button is located next to the power cord inlet.
-
Page 71: Tv Programming Instructions
CHAPTer 10: TreAdmill SPeCifiCATioNS ANd ASSembly GUide 10.4 TV ProGrAmmiNG iNSTrUCTioNS 1) Press ENTER, 1, 0, 0, 1, ENTER on the number keypad on the upper display and Manager Mode will appear on the display. 2) Press the key next to TV (Figure A), and then press the key next to CHANNEL SCAN (Figure B). fiGUre A fiGUre b 3) Press the - key on the number keypad and a Menu will appear on the TV (Figure C). - Page 72 CHAPTer 10: TreAdmill SPeCifiCATioNS ANd ASSembly GUide 10.4 TV ProGrAmmiNG iNSTrUCTioNS - CoNTiNUed 6) Use the channel keys to scroll down to CHANNEL SCAN, and then use the volume key to select it (Figure E). 7) Use the channel keys to scroll the cursor down to START TO SCAN and use the volume key to select it (Figure F). fiGUre e fiGUre f 8) Allow the channel scan to run.
-
Page 73: Chapter 11: Software Upgrade Guide
CHAPTer 11: SofTWAre UPGrAde GUide 11.1 SofTWAre UPGrAde iNSTrUCTioNS 1) Copy three software files (T1xe deploy.cab, io.txt, and update.config) onto a USB drive. 2) Turn on the power to the treadmill, wait until the standby picture has been cleared (Figure A). 3) Insert the USB drive into the Reprogram Port in the back of the console back cover (Figure B). - Page 74 NoTeS...
- Page 75 m ATrix fiTN eS S Sy S Tem S C o r P. 1610 LANDMARK DRIV E C OTTAGE GR O VE WI 535 27 U S A w w w. m a t r i x f i t n e s s . c o m TOLL FREE 866.693.4863 FA X 6 08.