Sanyo PLC-XP30 User Manual page 46

< Electrical Parts List> Note: Part order must contain Chassis No., Part No., and descriptions.
Product safety should be considered when a component replacement is made in any area of a Projector. Components indicated by a
the schematic diagram show components whose value have special significance to product safety. It is particularly recommended that only parts specified on the follow-
ing parts list be used for components replacement pointed out by the mark.
Read description in the Capacitor and Resister as follows:
CAPACITOR
CERAMIC 100P K 50V
FIXED RESISTER
CARBON 4.7K J A 1/4W
Rated value
Material :
CARBON
MT-FILM
OXIDE-MT
SOLID
MT-GLAZE
WIRE WOUND
CERAMIC RES
FUSIBLE RES
RESISTER
Rated Voltage
Rated value: P=Pico farad,
Material :
CERAMIC Temperature compensating ceramic
High dielectric rate ceramic
Semiconductor ceramic
MT-PAPER Metallized paper
POLYESTER Polyester
MT-POLYEST Metallized polyester
POLYPRO Polypropylene
MT-POLYPRO Metallized polypropylene
COMPO FILM Composite film
MT-COMPO Metallized composite film
STYRENE Styrol
TA-SOLID Tantalum oxide solid electrolytic
AL-SOLID Aluminum solid electrolytic
ELECT Aluminum foil electrolytic
NP-ELECT Non-polarized electrolytic
OS-SOLID Aluminum solid capacitors with
organic semiconductive electrolyte
POS-SOLID Polymerized organic semiconductor
DL-ELECT Electric double layer electrolytic
AL-SOLID Aluminum manganese wind solid
PPS-FILM Polyphenylene sulfide film
MT-PPS-FILM Metallized Polyphenylene sulfide film
MT-PEN-FILM Metallized polyethylenenaphthalate film
A EP-ELECT
Electric Conductor Polymerized Aluminum foil electrolytic
CAPACITOR Other
Rated Wattage
Tolerance Symbols:
A: ±0.05%
B: ±0.1%
C: ±0.25%
D: ±0.5%
F: ±1%
G: ±2%
J: ±5%
K: ±10%
M: ±20%
P: +5 ~-15%
Z: Use when 0 ohm
, ohms : K: X1,000 ohms. M: X1,000,000 ohms
Carbon film fixed
Metal film fixed
Metal oxide film fixed
Solid
Metal glaze type fixed
power type covered wiring fixed
Ceramic fixed
Fusible
Used for "others"
-46-
Marked ( Revised Aug. / 2000 )
A
( Revised May / 1998 )
Tolerance Symbols
U=Micro farad
Static capacitance of 10PF or less
A:
B:
C:
D:
F:
G:
H:
L:
R:
S:
E:
J:
K:
M:
Note: J. K. and M are used only for
tubular Ceramic Capacitors
Static capacitance of more than 10PF
A:
B:
C:
D:
F:
G:
E:
H:
J :
K:
L :
M:
N:
P:
Q:
R:
T:
U:
V:
W:
X:
Y:
Z:
Performance Symbols:
A: General
B: Flame retardance (including noncombustible)
Z: Low noise ( Less than 100Kohms : 0.3uV/V,
100Kohms to 1Mohm : 0.5uV/V,
More than 1Mohm : 1.0uV/V )
C~Y : Temperature characteristics
T: ±10ppm/˚C
U: ±25ppm/˚C
C: ±50ppm/˚C
D: ±100ppm/˚C
E: ±200ppm/˚C
F: ±250ppm/˚C
G: ±350ppm/˚C
H: ±1000ppm/˚C±10%
W: ±1200ppm/˚C±10%
Y: ±1400ppm/˚C±10%
J: ±2000ppm/˚C±10%
K: ±2400ppm/˚C±10%
L: ±2700ppm/˚C±10%
M: ±3000ppm/˚C±10%
N: ±3300ppm/˚C±10%
P: ±3600ppm/˚C±10%
Q: ±3900ppm/˚C±10%
R: ±4200ppm/˚C±10%
S: ±4300ppm/˚C±10%
V: ±4500ppm/˚C±10%
X: ±800ppm/˚C±150ppm/˚C
O: +500ppm/˚C ~ -250ppm/˚C
A
Note) ;
1. "General" (symbol A) means properties for which there are some differences among manu-
facturers but which can be used when within the range given in the catalogs.
2. Parts for which temperature characteristics are especially designated (required) due to
design are indicated by "temperature characteristic classifications" (symbol C to Y).Others
are indicated by "General" (symbol A).
3. What are called "cement resistors" are noncombustible,so are indicated as "General"(sym-
bol A),not "Flame retardant (including noncombustible)"(symbol B)
mark in this parts list and
Non-designated
±0.1PF
±0.25PF
±0.5PF
±1PF
±2PF
+0.1 ~ -0PF
+0 ~ -0.1PF
+0.25 ~ -0PF
+0 ~ -0.25PF
+0 ~ -1PF
±5%
±10%
±20%
Non-designated
±0.1%
±0.25%
±0.5%
±1%
±2%
±2.5%
±3%
±5%
±10%
±15%
±20%
±30%
+100 ~ -0%
+30 ~ -10%
+20 ~ -0%
+50 ~ -10%
+75 ~ -10%
+20 ~ -10%
+100 ~ -10%
+40 ~ -20%
+150 ~ -10%
+80 ~ -20%