Related Manuals for Socket CHS
Summary of Contents for Socket CHS
- Page 1 SerieS 7 1D ImageR quICkStaRt guIDe Model shown: CHS 7Ci Bluetooth Barcode Scanner CHS 7Ci,7Di,7DiRx www.socketmobile.com...
-
Page 2: Package Contents
Bluetooth SIG, Inc. USA, and any charging use by Socket Mobile, Inc. is under license. All other trademarks and trade names con- cradle tained herein may be those of their respective owners. -
Page 3: Scanner Setup
Insert the Batteries Charge the CHS unlock the Battery door by us- The CHS must be fully charged be- ing a thin coin to turn the lock fore first use. Please allow 5 hours under the CHS to a horizontal uninterrupted charging for the position (turn 90 degrees). -
Page 4: Basic Functionality
CHS beeps turns blue and the CHS beeps twice (high-low). 2. Aim, press and hold the trigger button. twice (low-high). By default, the CHS will beep, vibrate, and the LED will flash green to confirm successful scan. - Page 5 BLuETOOTH CONNECTION METHOdS BLuETOOTH CONNECTION METHOdS Operating System Connection Options Connect your CHS using one of the following Bluetooth modes: Bluetooth Operating Bluetooth Bluetooth Bluetooth Connection Profiles Apple Serial Systems devices Specific Bluetooth Mode description (OS) Support Support (iOS Mode) HID (Default)* •...
- Page 6 5. The CHS will connect to the Android device. 4. If a passkey is requested, enter 0000 (four zeroes). Click OK. 6. The CHS will beep once after it has connected and is ready to scan Or Pair Now. barcodes.
- Page 7 Windows: Connect Windows PC as a HID Peripheral Connect android & Windows mobile Device quickly: 1. Power on the CHS and scan this barcode. The CHS will beep 3 times. Highly recommended, allows two-way communications with Android, Blackberry, and Windows. SocketScan 10 software installation required.
- Page 8 4. Open SocketScan 10 application. 19. On the next screen, tap Pair. 5. When prompted to set SocketScan 10 as the keyboard language, tap 20. The CHS will beep once to indicate connected state and is ready to Back scan barcodes. Tap Back to close Socket EZ Pair.
- Page 9 5. Scan the barcode that appears on the screen. 3. In SocketScan 10 Settings, select an incoming Bluetooth serial COM 6. The PC will automatically try to pair with the CHS. If prompted to port. allow the pairing, click yes. If prompted for a passkey, enter 0000 Note: If there is none please click Ports to create a new incoming COM (four zeroes).
- Page 10 CHS. Note: The characters in brackets are the last 6 characters of the If you are using the CHS with an Apple iOS device and a Scanner-enabled Bluetooth Address. The full Bluetooth address is printed on the Product Application that does not provide instructions how to connect with the label.
-
Page 11: Bluetooth Unpairing
• If a connection is made, the Blue LEd will blink every 3 seconds. • If a connection is not made after 30 tries, the CHS will emit a long Important: Both steps above must be done to complete the unpairing. -
Page 12: Command Barcodes
COMMANd BArCOdES (CONTINuEd) Scan command barcode(s) to quickly configure the CHS. Important! Make sure the CHS is not connected to a host computer or device before scanning a command barcode! Make sure the CHS is not connected to a device before scanning a Bluetooth Connection Modes command barcode! See page 20 for unpairing instructions. - Page 13 COMMANd BArCOdES (CONTINuEd) COMMANd BArCOdES (CONTINuEd) Important! Make sure the CHS is not connected to a host computer or Vibrate Settings device before scanning a command barcode! Beep Settings Beep after CHS Vibrate “ON” (default) Decodes Data ON Enables CHS to vibrate to (default) indicate successful scans.
-
Page 14: Status Indicators
High-low tone Power Off 1 low beep Keyboard Pop-up Enable 1 Blue blink every 3 CHS is connected to 1 beep CHS connected to device and ready to scan bar- seconds device. codes. 1 beep with data successfully scanned. Good read Green Constant data successfully scanned. -
Page 15: Product Specifications
CHS will power off. Scanner type Imager (1d) If a device connects to the CHS, it stays on for 2 hours then turns Symbologies All major 1d barcodes off if a button is not pressed. If a button is press the timer is Supported Language reset to expire in another 2 hours. -
Page 16: Helpful Resources
Warranty Checker: generates, uses and can radiate radio frequency energy and, if not http://www.socketmobile.com/support/warranty-checker installed and used in accordance with the instructions, may cause Socket mobile Developer Program: harmful interference to radio communications. However, there is no Learn more at: http://www.socketmobile.com/developers guarantee that interference will not occur in a particular installation. -
Page 17: Limited Warranty
(1) year from the date of purchase. Product must be purchased the applicable Directives, 2004/108/EC and 2006/95/EC. new from a Socket Authorized distributor or reseller. used products and products purchased through non-authorized channels are not eligible for WASTE ELECTrICAL ANd ELECTrONIC EQuIPMENT this warranty support. - Page 18 NOTES NOTES...
- Page 19 extend Your Warranty... receive Priority Service and Personal Care. you have 60 days from purchase date to enroll in a SocketCare Service Program! Please provide your device serial number from the label below when enrolling: Serial Label Here for detailed information visit: http://www.socketmobile.com/socketcare 2015 # 6430-00338P...
Need help?
Do you have a question about the CHS and is the answer not in the manual?
Questions and answers