Husqvarna TC 450 2009 Service Manual page 45

TC 450-510 - TXC 250-450-510/2009,
TE 250-310-450-510/2009-I.E.,
SMR 450-510/2009-I.E.
Note Pos. N. Cod. Q.tà
Q.ty
Notes No. Code No.
Notes Q.te
N. Nr. Code
Marke M.ge
Index Code Nr
Notas N. Cod. C.ad DENOMINAZIONE
Pos.
1 8A00 A5603 1 Carter motore accoppiati compl.
(250-310)
M 1 8A00 A5671 1 Carter motore accoppiati compl.
1 8A00 A6445 1 Carter motore accoppiati compl.
(TC 450-510)
1 8A00 A7275 1 Carter motore accoppiati compl.
(TXC-TE 450-510)
2 8000 99846 1 Cuscinetto ALBERO MOTORE
(ø30xØ72x19 mm) (450-510)
2 8000 A2767 1 Cuscinetto ALBERO MOTORE
(ø30xØ62x16 mm) (250-310)
3 8000 97941 2 Piastrina
M 4 8A00 55241 5 Vite (M6X14 mm)
WCT 4 8A00 55241 3 Vite (M6X14 mm)
5 8000 99847 1 Cuscinetto ALBERO PRIMARIO
(ø17xØ40x12 mm)
6 8A00 43567 1 Cuscinetto ALBERO SECON-
DARIO (ø25xØ52x15 mm)
7 8000 51746 3 Piastrina
M 8 8A00 19768 1 Cuscinetto CONTRALBERO
(ø15xØ42x13 mm)
M 9 8000 91602 1 Piastrina
10 8000 65884 1 Cuscinetto ALBERO COM.
FORCELLE CAMBIO
(ø25xØ37x7 mm)
11 8000 34451 1 Anello di tenuta
(ø12xØ19x5 mm)
12 8A00 65847 1 Bussola
13 8000 59977 1 Anello di tenuta
(ø32xØ40x5 mm)
14 1610 77703 2 Bussola
15 8000 73500 1 Bussola
16 1610 77601 1 Bussola
N° Catalogo - Catalog No. - Nr. Catalogue - Katalog Nr. - N° Catalogo : 8000H0367 Pagina emessa Settembre'08 - Page issued September '08 - Page imprimée Septembre '08 - Seite Herasgegeben September'08 - Pagina emitida Septiembre '08
SEMICARTER SINISTRO - L.H. HALF CRANKCASE
CARTER G. - GEHAUSEDECKEL L.
BANCADA IZQ.
NAME
Crankcase assy (250-310)
Crankcase assy
Crankcase assy (TC 450-510)
Crankcase assy
(TXC-TE 450-510)
Bearing
(ø30xØ72x19 mm) (450-510)
Bearing
(ø30xØ62x16 mm) (250-310)
Plate
Screw (M6X14 mm)
Screw (M6X14 mm)
Bearing (ø17xØ40x12 mm)
Bearing (ø25xØ52x15 mm)
Plate
Bearing (ø15xØ42x13 mm)
Plate
Bearing GEARBOX
GEAR SHAFT
(ø25xØ37x7 mm)
Seal ring
(ø12xØ19x5 mm)
Bushing
Seal ring
(ø32xØ40x5 mm)
Bushing
Bushing
Bushing
DESIGNATION BESHREIBUNG
Carter compl. (250-310) Kurberlgehause kpl. (250-310)
Carter compl. Kurberlgehause kpl.
Carter compl. (TC 450-510) Kurberlgehause kpl.
(TC 450-510)
Carter compl. Kurberlgehause kpl.
(TXC-TE 450-510) (TXC-TE 450-510)
Roulement Lager
(ø30xØ72x19 mm) (450-510) (ø30xØ72x19 mm) (450-510)
Roulement Lager
(ø30xØ62x16 mm) (250-310) (ø30xØ62x16 mm) (250-310)
Plaquette Plättchen
Vis (M6X14 mm) Schraube (M6X14 mm)
Vis (M6X14 mm) Schraube (M6X14 mm)
Roulement (ø17xØ40x12 mm) Lager (ø17xØ40x12 mm)
Roulement (ø25xØ52x15 mm) Lager (ø25xØ52x15 mm)
Plaquette Plättchen
Roulement (ø15xØ42x13 mm) Lager (ø15xØ42x13 mm)
Plaquette Plättchen
Roulement ARBRE COMM. Lager ANTRIEBSWELLE
FOURCHES SCHALTGABEL
(ø25xØ37x7 mm) (ø25xØ37x7 mm)
Bague de retenue Dichtring
(ø12xØ19x5 mm) (ø12xØ19x5 mm)
Douille Buchse
Bague de retenue Dichtring
(ø32xØ40x5 mm) (ø32xØ40x5 mm)
Douille Buchse
Douille Buchse
Douille Buchse
TAVOLA
8
DRAWING
TABLE
BILD
TABLA
Validità
Validity
Validité
Gultig
DENOMINACION
Validez
Carter motor completi (250-310)
Carter motor completi
Carter motor completi
(TC 450-510)
Carter motor completi
(TXC-TE 450-510)
Cojinete
(ø30xØ72x19 mm) (450-510)
Cojinete
(ø30xØ62x16 mm) (250-310)
Placa
Tornillo (M6X14 mm)
Tornillo (M6X14 mm)
Cojinete (ø17xØ40x12 mm)
Cojinete (ø25xØ52x15 mm)
Placa
Cojinete (ø15xØ42x13 mm)
Placa
Cojinete EJE MANDO
HORQUILLA CAMBIO
(ø25xØ37x7 mm)
Anillo de retención
(ø12xØ19x5 mm)
Manguito
Anillo de retención
(ø32xØ40x5 mm)
Manguito
Manguito
Manguito
45