ADDING PRINTERS IN UNIX/LINUX........41 Configuring Host File .................. 41 Printing by LPD/LPR ................... 41 Using WUS-3200 on BSD UNIX/Linux............41 Using WUS-3200 on RedHat Linux (Fedora Core) ........43 CHAPTER6 FILE SERVER FUNCTION ............50 Preliminary....................50 Storage Names....................50 Connecting USB Mass Storage to WUS-3200..........
Page 3
Connecting HP All-in-one MFP to WUS-3200 ..........59 Using the Shared Scanner in Windows............59 Using the Shared Scanner in Linux.............. 64 CHAPTER8 MFP SERVER CONTROL CENTER.......... 66 Installing MFP Server Control Center............66 Using MFP Server Control Center............... 66 CHAPTER9 MFP SERVER’S WEB PAGES ............
Chapter1 Introduction Thank you for purchasing the WUS-3200 USB MFP server. This product is designed to connect your printers, USB Mass Storage/Memory Card Reader, and scanners of HP all-in-one printers (MFP), anywhere in your wired or wireless network, allowing all network users access to shared USB devices resources.
2.2.1 Start-up Procedures for Windows If your computer is configured to auto start CDs, the WUS-3200 USB MFP Server Product CD will start automatically when inserted. You can also navigate to the CD and start the autorun.exe file from within the Windows file...
The wireless network access (802.11b/g) is enabled by inner antenna. 2.3.3 USB Host Ports WUS-3200 has two USB host ports which are USB 1.1/2.0 low, full and high speed compliant and successfully tested with USB 1.1/2.0 printers, Mass Storage and HP all-in-one (HPAIO) series printers (MFP).
Page 7
most of the parameters and settings to factory default values performing the new firmware upgrade using in fallback. Please refer to Chapter 14, procedure C for detail description. 2.3.5 Indicators Power Indicator is lit while power is applied. If it is not lit, or if it blinks, there is a problem with MFP server or Power Adapter.
Installation Methods 2.4.1 Installation and Integration Refer to the table below to select the appropriate installation method. MFP Server Control Center tool is available on the WUS-3200 USB MFP Server Product CD or from LevelOne’s web site. Function Method Description...
Center, using Windows. These web pages or PC tools offer you a management tool that is suitable for all supported network environments. Features and Benefits WUS-3200 provides the following features and benefits: 1. Reliability: The MFP server provides high performance and reliability combined with low power consumption.
PC/devices with the same SSID (Service Set ID). Wireless access can be secured by WEP64, WEP128, or WPA-PSK/TKIP. In infrastructure mode, if network administrator wants to change any security related parameters, WUS-3200 should be changed first,...
Page 11
3.2.2 Set Wireless Configuration Using MFP Server Control Center 1. Install MFP Server Control Center. MFP Server Control Center is available in the WUS-3200 USB MFP Server Product CD. 2. Start MFP Server Control Center and Auto-searching MFP server window will appear.
Page 12
4. Double click the highlight list and type the server’s administrator (default: admin) and password (default: admin). 5. After you login successfully, from the Server menu, select wireless. The set Wireless dialog appears.
Page 13
6. In order to join an existing wireless network, you have to set the correct network type (infrastructure or ad-hoc), SSID, and the correct security method with the correct key information. 7. If the wireless network is secured by WEP64 or WEP128, authentication method, key index, and WEP key must be set correctly.
Page 14
In infrastructure mode, WUS-3200 searches all channels to join the matched wireless service set. In ad-hoc mode, WUS-3200 searches all channels to join the matched wireless ad-hoc service set too, however, if none are found, WUS-3200 creates that service set in the assigned channel.
Page 15
If the wireless parameters are not correct or not set yet, you have to use LAN to access Web Pages. If the TCP/IP parameters of WUS-3200 are not correct, you have to use MFP Server Control Center to set the TCP/IP parameters first.
Page 16
5. In order to join an existing wireless network, you have to set the correct network type (infrastructure or ad-hoc), SSID, and the correct security method with the correct key information. 6. If the wireless network is secured by WEP64 or WEP128, key index and WEP key must be set correctly.
Page 17
7. If the wireless network is secured by WPA-PSK/TKIP, the shared key must be set correctly.
IP address from your network administrator. 3.3.4 Methods for Setting the IP Address You can set the IP address of your WUS-3200 USB MFP server using one of the following methods, depending on your network operating environment: Automatic IP Address Assignment...
Page 19
3.3.5 Host Names and Host Name Rules The host name of the WUS-3200 USB MFP server is specified by “WUS-3200”in Factory Parameter. If you put two or more MFP servers in your local area network, to avoid using same host names you have to change the host names by using MFP Server Control Center or server’s web pages.
Page 20
3. Double click the highlight list and type the server’s administrator (default: admin) and password (default: admin). 4. After you login successfully, from the Server menu, select TCP/IP. The Set IP Address dialog appears.
Page 21
5. Click the button that corresponds to your choice of IP setting method (static or dynamic using DHCP). When assigning a static IP address you also have to define Subnet Mask and Default Gateway. If you choose Automatically get IP by DHCP, you can use desired DNS by clicking the Manual DNS button and manually assigning a DNS.
Page 22
If the TCP/IP parameters of WUS-3200 are not correct, you have to use MFP Server Control Center to set the TCP/IP parameters first. 2. Go to the web page and click CONFIG icon. 3. Login your administrator (default: admin) and password (default: admin).
5. Click the button that corresponds to your choice of IP setting methods (static or dynamic using DHCP). When assigning a static IP address you also have to define Subnet Mask and Default Gateway. 6. Click Submit to save your settings. And the server will reboot. 7.
Page 24
Using MFP Server Control Center 1. Start MFP Server Control Center and Auto-searching MFP server window will appear. 2. If the tool finds MFP servers in your local area network, then you have to select a MFP server from the server list. 3.
4. Set your printer names in Printer Name box and then click Apply. 3.4.2 Storage Names The local drives of the two storages in USB1 port and USB2 port are named as USBx_DxPx, where USBx represents the USBx port, Dx represents the the x-th Disk (in particular to card reader plugging in multiple cards) and Px represents the x-th partition.
Turn on “Use Add Network Printer by Configure Your MFP Printer Online” in Server Windows Standard Installed Window Method Printer Driver PC User Software Connecting WUS-3200 MFP Server To configure your server correctly, you have to know what type of network...
Page 27
topology your server connecting to. 4.2.1 MFP Server and Windows PC on Same LAN LAN HUB/Switch MFP Server USB Printer 4.2.2 MFP Server and Windows PC on Different LANs Example: Wired Windows PC across Internet Router LAN HUB/Switch Internet MFP Server Router LAN HUB/Switch USB Printer...
Setting up Local Windows Printer Driver You are advised to install your Windows printer driver in advance. For most printers, you can install the printer drivers as the following procedure: 1. Click Start, click Control Panel, click Printers and Other Hardware, and then click Printers and Faxes.
Page 29
Next. 5. In the Printer Name or IP Address box, type host name of the MFP server (default: WUS-3200) or IP address of MFP server. In the Port Name box, type your desired names or USB1_LPR or USB2_LPR for...
Page 30
If your server is running on a different LAN than your Windows PC such as Internet PC, you must type server’s IP address in Printer Name or IP Address box. 6. Click Next. 7. Click Custom/settings.
Page 31
8. Click Settings and confirm that the settings are as below. The queue names are USB1_LQ, USB2_LQ for USB1 port 1 and USB2 port, respectively. Click OK. 9. Click Finish...
Page 32
4.4.2 Using MFP Server Control Center for LPR Printing Windows Platform: Windows 2000, XP and 2003 1. Start MFP Server Control Center, select your MFP server and click Add Printer. 2. Select USB1 Port or USB2 Port to add the printer in Add the printer box, choose to use host name or IP address to represent MFP server in Select IP address or Host Name in printer port box, and select the network printing protocol of Printing with LPR (Line Printer...
Page 33
If your server is running on a different LAN than your Windows PC such as Internet PC, you must choose IP address in Select IP address or Host Name in printer port box. 3. Click Apply. 4. Select the desired printer driver and click Set Port to Printer.
Page 34
Next. 5. In the Printer Name or IP Address box, type host name of the MFP server (default: WUS-3200) or IP address of MFP server. In the Port Name box, type USB1_RAW or USB2_RAW for printer connected to USB1 port and USB2 port, respectively.
Page 35
8. The click Settings and confirm that the settings are as below. The default Port Number values are 9100, 9101 for USB port 1 and USB port 2, respectively. Refer to server’s web pages or MFP Server Control Center tool, you can get exact values. Click OK. 9.
Page 36
4.4.4 Using MFP Server Control Center for Raw TCP/JetDirect Printing Windows Platform: Windows 2000, XP and 2003 1. Start MFP Server Control Center, select your MFP server and click Add Printer. 2. Select USB1 Port or USB2 Port to add the printer in Add the printer box, choose to use or IP address to represent MFP server in Select IP Address or Host Name in printer port box, and select the network printing protocol of Print with Raw TCP Mode.
Page 37
If your server is running on a different LAN than your Windows PC such as Internet PC, you must choose IP address in Select IP Address or Host Name in printer port box. 3. Click Apply. 4. Select the desired printer driver and click Set Port to Printer.
5. If you can not find any printer driver in Printer List, please install your printer driver first or click Add New Printer to install the printer driver. 4.4.5 Using Standard Windows Methods for SMB/CIFS Printing Before using SMB/CIFS printing, you have to login the SMB/CIF Print/File server in advance and then you may use it;...
Page 39
(Please refer to server’s web pages or MFP Server Control Center tool to know exact path). For example: if you set server’s host name as WUS-3200 and printer name (USB1 port) as psc 1300 ser, then the network path is expressed as: \\WUS-3200\psc 1300 ser ...
Page 40
Windows Platform: Windows 98SE, ME, 2000, XP and 2003 1. Start MFP Server Control Center, select your MFP server and click Add Printer. 2. Select USB1 Port or USB2 Port to add the printer in Add the printer box, choose to use host name or IP address to represent MFP server in Select IP Address or Host Name in printer port box, and select the network printing protocol of Printing with Network Path (SMB).
Page 41
If your server is running on a different LAN than your Windows PC such as Internet PC, you must choose IP address in Select IP address or Host Name in printer port box. 3. Click Apply. 4. Select the desired printer driver and click Set Port to Printer. 5.
Page 42
Internet or on a home or office network. In the URL: field, enter the following to connect to MFP server: http://sercver’s host name /printer name or http:/server’s IP address /printer name For example, http://WUS-3200/psc 1300 ser If your server is running on a different LAN than your windows...
Page 43
5. Click Next and then continue Windows Add Printer Wizard.
Log in to Linux machine by “root”. # login root 2. Register WUS-3200 MFP server’s host name and IP address to /etc/hosts file. To edit host file, use an editor, e.g. “vi”. Example: The IP address is “192.168.1.100”, host name is “WUS-3200”...
Page 45
WUS-3200 MFP server to /etc/printcap file. Example: To register the printer of USB1 port by the printer name “Printer1”. Printer1:\ ---(A) :lp=:rm=WUS-3200:rp=USB1_LQ:\ ---(B) :sd=/var/spool/lpd/Printer1:\ ---(C) :lf=/var/spool/lpd/Printer1/Printer1_errs: ---(D) where (A) Describes the printer name. (B) lp: Device file name to connect printer. No name designation required on the network.
Using WUS-3200 on RedHat Linux (Fedora Core) In the RedHat (Fedora Core) x-window user interface, do the steps as follows: 1. To start the application, select Main Menu button (on the Panel)-> Applications->System Settings -> Printing. 2. Click on the New button in the Printer configuration window.
Page 47
4. Fill in your desired printer name and description (optional) in Queue name window and then click on the Forward button. 5. In Queue type window, you will now be asked to specify which Printer Queue type you are using, select the one option form Networked Unix (LPD), Networked CUPS (IPP), Networked Windows (SMB) and Networked JetDirect options.
Page 48
6. Fill in parameters for Queue type window: A. Networked Unix (LPD): Fill in MFP server’s IP address and queue name and then click the Forward button. Example: If your MFP server’s IP address is 192.168.1.100 and it connects HP PSC 1300 MFP via USB1 port.
Page 49
Networked JetDirect: Fill in MFP server’s IP address and protocol’s TCP port and then click the Forward button. Example: If your MFP server’s IP address is 192.168.1.100 and it connects HP PSC 1300 MFP via USB1 port. You can type IP in server box as 192.168.1.100 and TCP Port in Port box as 9100.
Page 50
Fill in the Workgroup, Host name, User name and Password in Authentication window and then click on the OK button. iii. Click on the Forward button. Networked CUPS (IPP): Fill in MFP server’s IP address and printer name then click the Forward button. Example: If your MFP server’s IP address is 192.168.1.100 and its printer name is psc 1300 ser.
Page 51
7. Select your printer driver. Click on the Forward button. Windows will display the Finish, and create the new print queue folder. 8. Click Finish button.
Chapter6 File Server Function This chapter describes the file server function of WUS-3200 MFP server which allows USB storage devices to be shared across a network by using SMB: NetBIOS over TCP/IP and FTP protocol. Preliminary 1. This product supports a file format of FAT12/16/32. It will not support a drive formatted by NTFS, etc.
MFP Server supports Windows Codepages. If users want to communicate files using FTP client tool or SMB on Windows 98SE/Me/2000 with WUS-3200 MFP server, they have to set their MFP server code page to be same as the codepage that their Windows PC is using.
Page 55
5. Select your code page form File Server Code Page box and click Apply. Using Server’s Web Pages 1. Go to the web page, click CONFIG 2. Login your administrator (default: admin) and password (default: admin). 3. After you login successfully, setting General Configuration dialog appears.
SMB/CIFS: NetBIOS over TCP/IP The protocols are shown in Supported Protocols box of MFP Control Center or server’s web pages. 6.5.1 Setting up File Server Using MFP Control Center 1. Start WUS-3200 MFP Server Control Center and Auto-searching MFP...
Page 57
server window will appear. 2. If the tool finds MFP servers in your local area network, then you have to select a MFP server from the server list. 3. Double click the highlight list and type the server’s administrator (default: admin) and password (default: admin). 4.
Page 58
b) Set FTP Server: Enable FTP Server: select the item, if you want to support FTP server. FTP port: type the desired FTP port. The default value is 21. Maximum Session Number: select the item and fill in desired number. Enable Passive Mode: select the item, if you want to allow that your FTP server can accept passive mode command.
Page 59
4. Set up File Server Configuration: c) Set SMB/CIFS Print/File Server Enable SMB/CIFS Print/File Server: select the item, if you want to support SMB/CIFS print/File server. Enable Internet Access: clear the item, if you do not allow that users can access your SMB/CIFS server via Internet. If you select the item, you allow Internet users can access your storage using the SMB/CIFS protocol.
Page 60
Workgroup name is “LevelOne”. You can refer to WUS-3200 MFP Server Control Center or server’s web pages to get it. You will see that the MFP server will be displayed as the default host name "WUS-3200" or the host name that you have set.
Page 61
9. The shared folders will be listed as USB1_DxPx, and USB2_DxPx where Dx represents the x-th disk and Px represents the x-th partition with respect to USB1 port and USB2 port. 10. Perform Open, Paste, Remove or Copy the files to the shared folders. 6.5.4 Use Shared Storage by FTP Methods for Windows Use Microsoft IE to the shared USB Mass Storages...
USB scanner of HP OJ/PSC/all-in-ones series, connected to this product, to be shared as a network scanner. The scan server function is available in any platform that can use SANE client. Connecting HP All-in-one MFP to WUS-3200 LAN HUB/Switch HP MFP...
Page 63
3. Set the options. The options are defined as follows: Source: choose flatbed scanning or scrolledbed (ADF) scanning Mode: choose lineart (black/white), Gray and color mode Resolution: choose the image resolution Contrast: tune the contrast of the image Brightness: tune brightness of the image Range: define the scanning range of the image Not all the MFP scanners support the options above.
Page 64
Prior to using scanning functions in Windows applications such as MS Word, Photoshop …etc, you have to install network scanner’s TWAIN driver in advance. When you install MFP Server Control Center tool, it will also install this TWAIN driver. Example: Using Photoshop 1. Start Photoshop, click File ->Import->WUS-3200 Network Scanner...
Page 65
MFP servers in your network. If LevelOne control center software and application program (ex:photoshop) are started up simultaneously, you may need to configure the IP address of WUS-3200 manually. Or you can close the control center software to enable auto-search.
Page 66
3. Click Connect to Network Scanner button in Server Information...
4. Select your scanner in Server Information box. 5. Click Preview button 6. Adjust the window size to be scanned 7. Click Scan button Using the Shared Scanner in Linux 7.3.1 Using XSane in Redhat Linux 1. Download SANE-Backends from http://www.sane-project.org 2.
Chapter8 MFP Server Control Center This chapter describes how to use MFP Server Control Center in your Windows. Installing MFP Server Control Center 1. Click Install Product button. 2. Click Next, if you see Next button in installation windows. 3. Click Finish. Using MFP Server Control Center 8.2.1 Use Tools of MFP Server Control Center...
Page 70
File Server Code Page: If users want to communicate files using FTP client tool or SMB on Windows 98SE/Me/2000 with WUS-3200 MFP server, they have to set their MFP server code page to be same as the codepage that their Windows PC is using.
Page 71
TCP/IP: You have to set the server’s TCP/IP configuration to connect TCP/IP network. Please see Chapter 3 Basic Installation for more details. Supported Protocols: The server supports the following TCP/IP protocols: TCP/IP Enable LPR (Line Printer Remote) Printing: select or clear Enable LPR Printing support.
Page 72
port (default: 21) Set Maximum Session Number: select or clear Set Maximum Session Number support. You can limit the FTP session number by selecting the support and type an integer to set the allowable maximum session number. If you clear the support, it means that FTP server will have not any limitation in session number.
Page 73
User Accounts: You can change administrator name and password or add a user account for SMB/CIFS Print/File server and FTP File server. If you forgot administrator name and password, you must to perform Restore Factory Default action by pressing Init button and plugging Power adaptor simultaneously.
Page 74
Add: click Add button, after entering the user name, corresponding password, and Permission selection. The account will take effect once shown in the blank below. Delete: delete the existing user account. SNMP: You can set community and some parameters for SNMP server. Furthermore, you can enable SNMP v3 for more security.
Page 75
EnableAuthenTrap: type 1 or 2 for the variable of EnableAuthenTrap that represents to enable (1) or disable (2) to send Trap packets receiving the wrong Community name. SNMP V3 Enable SNMP V3: select or clear Enable SnmpV3 support User Security name: set user security name of SNMP v3 Auth Password: set authentication password of SNMP v3.
Page 76
From Address: type the sender’s e-mail address. To Address: type an e-mail address to send that mail to a person. Cc: stands for carbon copy; type an e-mail address to send that mail to a second person. SMTP Server requires authentication: login to remote SMTP server which requires authentication.
Page 77
Maintenance: If you want to restart server, restore factory default values of the server, download new firmware file from product’s public web site and upgrade new firmware, you can use the Maintenance tool. Restart Server: click the button, the server will be restarted. Factory Default: click the button, the server will restore factory default values.
Chapter9 MFP Server’s Web Pages Introduction WUS-3200 USB MFP server runs the daemon of http server, httpd on TCP port: 80. Users may use the web pages to see the server’s system status and configure the server. Using Server’s Web Pages 9.2.1...
Page 79
File Server Code Page: if users want to communicate files using FTP client tool or SMB on Windows 98SE/Me/2000 with WUS-3200 MFP server, they have to set their MFP server code page to be same as the codepage that their Windows PC is using.
Page 80
USB Device Information: You can set printer names and display some information of USB mass storages and scanners. Please refer to Chapter 4, Chapter 6 and Chapter 7. TCP/IP: You have to set the server’s TCP/IP configuration to connect TCP/IP network. Please see Chapter 3 Basic Installation for more details.
Page 81
support. It is enabled in Factory Default. Enable Raw TCP Printing: select or clear Enable Raw TCP Printing support. It is enabled in Factory Default and users may set the protocol’s TCP ports as following boxes: TCP Port 1: set TCP port for the printer of USB1 port (default: 9100) TCP Port 2: set TCP port for the printer of USB2 port (default: 9101)
Page 82
you need to type user name and password to login to the server. If you clear the support, you do not need user name and password to enter the server. Allow Anonymous Login: select the item, if you want to allow the user “anonymous”...
Page 83
User Accounts: You can change administrator name and password or add a user account for SMB/CIFS Print/File server and FTP File server. If you forgot administrator name and password, you must to perform Restore Factory Default action by pressing Init button and plugging Power adaptor simultaneously.
Page 84
SNMP: You can set community and some parameters for SNMP server. Furthermore, you can enable SNMP v3 for more security. Set SNMP Configuration Authentic Community: set Community name of SNMP server. Trap Community: set Trap Community name for SNMP server to send trap packets.
Page 85
Email: If you want to receive some alerting mail from the server, you have to enable SMTP Protocol, and set Email configuration. You can set new SMTP port number (default: 25). Set Email Configuration SMTP Protocol: select or clear Enable SMTP support SMTP Server Name: type your SMTP server’s host name or IP address.
Page 86
Restart Server: click the button, the server will be restarted. Maintenance If you want to restore factory default values of the server and upgrade new firmware, you can use the Maintenance tool. Factory Default: click the button, the server will restore factory default values.
Page 88
Chapter10 Email Alerting WUS-3200 USB MFP server can send some email messages to the user while the following events occurs 1. Add/Remove USB device: When add new USB device or remove current USB device, the server will send the mail to notify the user.
Page 89
Users can use SNMP client software as actual management tool such as HP Open view to management your MFP server. The WUS-3200 MFP servers support all relevant parts of MIB-II and a private WUS-3200 MFP server MIB. You can set value of some MIB variables from the server’s web pages or MFP...
WUS-3200 USB MFP server. Fault symptoms, possible causes and remedial actions are provided within a quick reference table. General USB ports in WUS-3200 USB MFP server only support USB printers, USB Mass storages and USB scanner of HP Office Jet Series.
Page 91
Storage Error There are errors in network File server. Scanner Ready Scanner is ready. Flatbed Scanning Flatbed of scanner is scanning. Scrollfed Scrollfed of scanner is scanning. Scanning Error There are errors in network scanning.
Chapter13 Restore Factory Default This chapter describes how to restore default parameters of the MFP server. The server provides the following methods to achieve restoring default parameters of the MFP server. 13.1 Using Server’s Web Pages 1. Go to the server’s web page and click CONFIG 2.
13.2 Using MFP Server Control Center 1. Start MFP Server Control Center and Auto-searching MFP server window will appear. 2. If the tool finds MFP servers in your local area network, then you have to select a MFP server from the server list. 3.
13.4 Default Parameters List Host Information Comment (Optional): WUS-3200 USB MFP Server Host Name: WUS-3200 Workgroup: LevelOne Code Page of File Server: Western European TCP/IP Automatically get IP using DHCP: enabled Manual DNS: none DHCP Failed: IP : 192.168.1.100 Subnet Mask: 255.255.255.0 Static IP: disabled IP: 192.168.1.100...
Procedures to upgrade new firmware Procedure A: Using PC User Software 1. Open the WUS-3200 MFP Server Control Center. It will automatically search the existing servers and display their status. 2. Select the server that you want to upgrade the firmware. Double click the selected server and enter Administrator Name and Password.
Page 97
WUS-3200's IP address. 5. Click CONFIG. 6. Login WUS-3200 with administrator "admin" and password "admin". 7. Click Maintenance. 8. Click Upgrade Firmware. 9. Click Browse button to choose the file of new WUS-3200 firmware. 10. Click Upload button to start firmware upgrade.
Page 98
11. Wait about 15 seconds for system reboot. Procedure C: Using Init Button and TFTP Client to Upgrade Firmware in Emergency 1. Simultaneously press Init button and power on (plug the power adaptor line) the server until LED indicators of Power, USB1 and USB2 blink.
Page 99
6. Plug-off power adapter and then plug-on the power adapter to restart server.
Chapter15 Init Button The Init button is used for: 1. Print Configuration Report: Press Init button for exceeding 3 seconds and then the connected HP printer or PCL supported printer will print out the system configuration. 2. Maintenance: Simultaneously press Init button and turn on (plug the power adaptor line) the server until USB1 and USB2 LED indicators simultaneously blink.
Page 101
following tasks: A. Perform a Factory Default of the MFP server, which will restore most of the parameters and settings to factory default values, B. Perform a TFTP server. You can upgrade new firmware using any TFTP client tool (refer to Chapter 14 Upgrade New Firmware Procedure C).
Chapter16 Technical Specifications Supported Printers Firmware Upgrade Support for printers and MFPs from Firmware upgrade using the internal Brother, Canon, Epson, HP, IBM, Kyocera, web pages, Windows Tool, and TFTP Lexmark, Minolta, NEC, Oce, OKI, Ricoh, Network Connection Sharp, Star, TEC, Toshiba, Zebra, Xerox, etc.
Scan Server Supported Systems Dimensions Microsoft Windows: 98SE, 2000, XP Height 2.6 cm and 2003 Width: 7.6 cm Supported Protocols Depth: 10.4 cm General Weight: 110 g DHCP, FTP, HTTP, SNMP v1/v2c/v3 Environmental Print Server Temperature: 40-105 °F (5-40 °C) TCP/IP: LPR, Raw TCP, NetBIOS over TCP/IP (SMB), IPP, Humidity 0 –...
WUS-3200 USB MFP server should support most USB printers (except some Host-based/GDI printers), and USB disks or USB memory cards. WUS-3200 USB MFP server should support the scanners of HP all-in-one printers (MFP). The supported MFPs are list below. Model...
Page 105
WUS-3200 USB MFP server should support the following printers to print configuration report using Init button Model Printer Business 1100 series, 2300 series, 2600 series, 3000 Inkjet series Desk jet 3600 series, 5100 series, 5550 series, 5600series, 5850 series, 6122 series, 6127...
Need help?
Do you have a question about the WUS-3200 and is the answer not in the manual?
Questions and answers