Table of Contents
Advertisement
Installation
Your refrigerator has been packed carefully for
shipment. Remove and discard shelf packaging
and tape. Do not remove the serial plate.
The following pages contain "Measuring and
Opening" instructions particular to each of the
models and sizes. Ensure you choose the correct
instructions for your model.
• If refrigerator is installed beside a cooking appli-
ance, (not recommended) it is important that there
be at least 5" (13 cm) between the refrigerator and
range for proper air circulation.
• Do not install refrigerator near a radiator or other
heat source. If not possible, shield refrigerator with
cabinet material.
• Do not install where temperature falls below 55° F
(13° C) or rises above 110° F (43° C). Malfunction
may occur at this temperature.
• Refrigerator is designed for indoor household
application only.
Measuring the Opening
30" Classic
(see page 9 #3015 diagram)
If refrigerator is to be installed into a recess, verify
and use the following dimensions
1.) Cut out height for refrigerator:
Option 1) Without optional cowl, and where the top
of the refrigerator is completely covered:
67 1/4" (171 cm) - space provides the necessary
gap above the refrigerator for tool access to fasten
anti-tip bracket (see details below)
Option 2) With 6" high optional cowl:
73 1/4 (186 cm) - provides enough space for op-
tional 6" cowl assembly
2.) Cut out width for refrigerator's main body: 30"
(77 cm)
3.) Max. cut-out depth: 27 1/2" (70 cm)
4.) When installing your refrigerator, measure care-
fully. Allow ½" space at top and ½" space behind the
machine compartment cover (located in the rear) for
proper air circulation.
Anti-Tip Bracket: Every refrigerator includes an
anti-tip bracket which must be properly installed
to prevent the refrigerator from tipping forward
should downward pressure be applied with both
doors open. To fasten bracket to the wall, distance
from fl oor to underside of bracket will be 66-1/4"
(169 cm) max. Mark wall where studs are located.
Fasten anti-tip bracket to the wall.
Subfl ooring or fl oor coverings (i.e. carpet, tile, wood
fl oors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the leveling
procedure under Leveling.
IMPORTANT: Corner Installations Classic: To al-
low door to open 90 degrees, corner installations
must allow 4" (10 cm) space between wall and
refrigerator on hinge side. Filler wood strip recom-
mended for aesthetics.
Measuring the Opening
36" Classic
(see page 10 #3115 diagram)
If refrigerator is to be installed into a recess verify
and use the following dimensions
1.) Cut out height for refrigerator:
Option 1) without optional cowl, and where the
top of the refrigerator is completely covered:
70" (177.8 cm) - space provides the necessary
gap above the refrigerator for tool access to fas-
ten anti-tip bracket (see details below)
Option 2) with 6" high optional cowl:
76 (193.1 cm) - provides enough space for op-
tional 6" cowl assembly
2.) Cut out width for refrigerator's main body: 36-
1/2" (93 cm).
3.) Max. cut-out depth: 24 1/2" (62 cm)
4.) When installing your refrigerator, measure care-
fully. Allow ½" space at top and ½" space behind the
machine compartment cover (located in the rear) for
proper air circulation.
Anti-Tip Bracket: Every refrigerator includes an
anti-tip bracket which must be properly installed
to prevent the refrigerator from tipping forward
should downward pressure be applied with both
doors open. To fasten bracket to the wall, distance
5
Use & Care Guide
Advertisement
Table of Contents
