Operating instructions Commercial dishwasher PG 8083 SCVi en - GB To avoid the risk of accidents or damage to the machine, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Notes on these instructions Text which is highlighted or emphasised Important warnings Information which is important for safety is highlighted in a thick framed box with a warning symbol. This alerts you to the potential danger of injury to people or damage to property. Read these warning notes carefully and observe the procedural instructions and codes of practice they describe.
Guide to the machine Machine overview a Upper spray arm (not visible) g Filter combination b Cutlery tray h Data plate c Upper basket i In-operation indicator light d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual compartment detergent dispenser f Lower spray arm...
Guide to the machine Control panel a Display e Programmes b 4 > (Further programmes) button f V (Programme selector) button for with indicator light scrolling through the programmes c , (Delay start) button with indicator g - (On/Off) button with indicator light light h In-operation indicator light d G+ (Additional drying) button with...
They contain important information be dangerous. on its safety, installation, use and Miele cannot be held liable for damage maintenance. caused by improper or incorrect use or Keep these instructions in a safe operation.
In order to ensure stability, a Repair work to the machine can only built-under or integrated commercial be carried out by the Miele Service dishwasher must only be installed Department or an authorised Miele Ser- under a continuous worktop which is vice Dealer.
If in any doubt, consult a available from Miele. For safety reasons qualified electrician. this must only be done by the Miele Service Department or an authorised There must be no electrical sockets Miele Service Dealer.
Warning and Safety instructions In areas which may be subject to Please be aware that the infestation by cockroaches or other dishwasher may be operating at high vermin, pay particular attention to temperaures. If the door is opened keeping the machine and its there is a danger of burning or surroundings in a clean condition at all scalding.
Follow the detergent Do not allow children to operate the manufacturer's safety instructions. commercial dishwasher. Miele cannot be held liable for any Keep children away from effect chemical cleaning agents may have on the material of the items being detergents.
Caring for the environment Disposal of the packing Disposing of your old machine material Electrical and electronic machines often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for disposal human health and to the environment.
Caring for the environment ^ When using powder or liquid Energy saving dishwashing detergent you can use less This commercial dishwasher is detergent if baskets are only half full. exceptionally economical in its use of water and electricity. You can make the most of your machine by following these tips: ^ If your water supply is suitable, this...
Before using for the first time To open the door To close the door ^ Push the baskets right in. ^ Then raise the door up, and push until it clicks into position. Do not put your hand inside the door as it is closing.
Before using for the first time Display General Settings menu The display is used to select or set the The Settings menu is used to alter the following: machine's electronics to suit different requirements. – the programme You access the settings menu by –...
Before using for the first time Basic settings In the event of a fault, it will help the service technician if you know the ^ Switch the machine on with the - hardness of your local water supply. button. Enter the water hardness below: If the dishwasher is being switched on for the first time, the welcome screen mmol/l or °d...
Before using for the first time Before using the machine for If the water in your area is very soft the first time, you require: and constantly lower than – approx. 1 kg dishwasher salt for 0.7 mmol/l (4 °d - German scale), reactivation, you do not need to add dishwasher salt.
Before using for the first time ^ When filling the salt reservoir only Do not fill the salt reservoir with open the door halfway to ensure water. that all the salt gets into the reservoir. ^ Press the button on the lid of the salt ^ Add salt only until the reservoir is full.
Before using for the first time "Add salt" message ^ Fill the salt reservoir with dishwasher salt for reactivation when the F salt message appears. (If it appears during a programme, wait until the end of the programme). ^ Confirm by pressing the middle button.
Before using for the first time Rinse aid Adding rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
Before using for the first time "Add rinse aid" message Add rinse aid When the message appears, the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid in plenty of time. ^ Confirm by pressing the middle button.
Loading the dishwasher Preparing the load – Wide based items should be placed at an angle so that water can run off Remove coarse food residues from them freely. crockery. – The spray arms must not be blocked There is no need to rinse items under by items which are too tall or hang running water.
Loading the dishwasher Items not suitable for We recommend: dishwashers: – When purchasing new crockery and cutlery, make sure they are – Wooden cutlery and crockery or dishwasher-proof. items with wooden parts: these may discolour and fade. The glue used in –...
Loading the dishwasher Upper basket Hinged spikes The rows of spikes can be lowered to For safety reasons, do not make more room for larger items such operate the dishwasher without the as casserole dishes. upper and lower baskets in place. ^ Press the yellow lever downwards a, and then lower the spikes b.
Loading the dishwasher ^ You can also move one of the side Jumbo cup rack inserts of the cutlery tray to make The cup rack can be set at two different more room for tall glasses. widths so that it can also accommodate large cups.
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the lower or upper basket, the upper basket can be Dishwashers with cutlery tray adjusted on three levels with 2 cm between each level.
Loading the dishwasher Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Glasses, cups and small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket.
Loading the dishwasher Removable MultiComfort insert Glass rack ^ The glass rack can be raised to make The rear section of the lower basket is used for washing cups, glasses, plates, more room for tall items. pots and pans. ^ Stem glassware, e.g. wine glasses or You can remove the MultiComfort insert champagne flutes, can be leaned to make more room for larger items...
Loading the dishwasher Glass rail This rail is designed to hold tall glasses and glasses with stems securely. ^ Press the yellow lever downwards a, and then lower the spikes b. Bottle holder ^ Lower the rail and lean tall glasses The bottle holder can be used to wash against it.
Loading the dishwasher Cutlery 3D cutlery tray If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
G 60 Semi DOS module (see "Settings menu, External dispensing"). For cleaning specific types of soiling please contact the Miele Service Department for advice on the optimum cleaning agent to use for the particular circumstances.
Operation The flap is always open at the end of a Avoid inhalation of powder programme. detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing.
Operation Switching on You can now select additional ^ Open the stopcock, if it is closed. functions (see "Additional functions"). ^ Open the door. Starting the programme ^ Make sure the spray arms are not ^ Start the programme by closing the obstructed.
Operation Time display Standby The duration of the programme To save energy, the dishwasher will selected appears in hours and minutes switch to Standby mode a few minutes in the display before the programme after the last time a button has been begins.
Operation At the end of the programme Switching off At the end of a programme, the At the end of a programme: In-operation indicator light will be ^ Open the door. visible flashing slowly with the door ^ Switch the machine off with the - shut.
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as If liquid detergent dispensing is not the door is opened. being used and the detergent If the door is closed again, the dispenser flap has already opened, programme will continue from the point then more powder detergent must it was at before the door was opened.
Additional functions Additional drying In order to achieve a better drying result and to minimise the amount of steam which escapes when the door is opened, the fan runs for longer at the end of the programme when Additional drying is selected. This function is not available for all programmes.
Additional functions Delay start If, after you have set the delay start time, you do not close the door within a The start time of a programme can be few seconds, the display will revert to delayed, e.g. to benefit from economy showing the programme duration.
Additional functions BrilliantLight This dishwasher has interior lighting. When the door is open the lighting will switch off automatically after 15 minutes. You can also switch off the interior lighting permanently. ^ Half open the dishwasher door and quickly swing it back and forth three times.
(available from damp cloth or a suitable cleaning Miele). agent designed for use on plastic. If you mainly use low temperature programmes, bacteria and unpleasant odours can build up in the wash cabinet.
Cleaning and care Cleaning the control panel and To avoid damaging the external surfaces, do not use: door front – cleaning agents containing soda, Remove any soiling immediately. ammonia, acids or chlorides, If this is not done, it might become –...
Cleaning and care Checking the filters in the Cleaning the filters wash cabinet ^ Switch the dishwasher off. The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms.
Cleaning and care ^ Replace the filter combination so that To clean the inside of the filter, the flap must be opened: it lies flat in the base of the wash cabinet. ^ Press catches a together in the ^ Then turn the handle clockwise to direction of the arrows as shown, and open the filter b.
Cleaning and care ^ Remove the lower basket. Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off.
Service Department, Repairs should only be carried out by the Miele Service Department or an authorised Miele Service Dealer. Unauthorised or incorrect repairs could cause personal injury or damage to the machine.
– Select the programme you want. – Close the door. If the fault message appears again, there is a technical fault. – Call the Miele Service Department. L Waterproof The Waterproof system – Close the stopcock. has reacted. – Call the Miele Service...
Problem solving guide Water inlet/drain fault Problem Possible cause Remedy The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: 2 Open stopcock The stopcock is closed. Open the stopcock fully. 2 Inlet Before rectifying the problem:...
Problem solving guide Problem Possible cause Remedy The In-operation Before rectifying the problem: indicator is flashing – Switch the machine off with the - button. quickly. The buzzer is The water outlet is – Clean the filter sounding. restricted, water combination.
Problem solving guide General problems with the dishwasher Problem Possible cause Remedy Press the - button. The indicators and The indicators and display are dark. Only display have switched This switches Standby off. the - indicator is off automatically to save flashing slowly.
Problem solving guide Problem Possible cause Remedy Detergent residue is left The dispenser was still Make sure the dispenser in the dispenser at the damp when detergent is dry before adding end of a programme. was added. detergent. The detergent dispenser Clogged detergent Clean the detergent from lid cannot be closed...
Problem solving guide Noises Problem Possible cause Remedy Knocking noise in the A spray arm is knocking Interrupt the programme, wash cabinet. against an item in a and rearrange the items basket. which are obstructing the spray arm. Items of crockery are Interrupt the programme, Rattling noise in the wash cabinet.
Problem solving guide Unsatisfactory washing result Problem Possible cause Remedy The dishes are not The dishes were not loaded See notes in "Loading the clean. correctly. dishwasher". The programme did not meet Select a suitable the cleaning requirments. programme. See Programme chart.
Problem solving guide Problem Possible cause Remedy Dishes, cutlery and The amount of rinse aid may Replenish the reservoir, glasses are not dry be insufficient, or the rinse increase the dosage or or are flecked. aid reservoir empty. change the brand of rinse aid (see "Before using for the first time, Rinse aid").
Problem solving guide Problem Possible cause Remedy Glassware has a This may be caused by the Change your detergent. brown or blue tinge, detergent. and film cannot be wiped off. Glassware is dull The glasses are not There is no remedy. and discoloured;...
^ Take care when withdrawing the filter union. This filter is available from the Miele Spares Parts dept. not to pull out or dislodge the flow regulator located underneath the Cleaning the filter: filter.
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Switch off the dishwasher and disconnect it from the mains.
Programme chart Programme When to use Detergent Follow the detergent manufacturer's recommendations on dosage. Compartment I Compartment II For fresh, easily removed food deposits Short 20 - 30 g For normal food deposits which have begun to dry on Medium 20 - 30 g For burnt-on, stubborn, dried-on food deposits containing starch or protein...
X = Sections included in a programme (X) = Optional sections which can be selected If a second interim rinse is required, this must be programmed into the machine by a Miele service technician. Optional temperature increase to 75 °C.
Programme chart Programme Consumption Duration Electricity Water Cold water Hot water Cold water Hot water connection connection connection connection (15°C) (55°C) (15°C) (55°C) Short 1.7 kWh 0.9 kWh 17 l 25 min 19 min Medium 1.7 kWh 1.0 kWh 17 l 38 min 30 min Intensive...
Optional accessories Making the most of the dishwasher Optional accessories for this dishwasher are available from Miele or your Miele Dealer. If you would like to … you will need to order … ... wash a Miele Cappuccinatore … a Cappuccinatore insert for the upper basket ...
THIS MACHINE MUST BE EARTHED carried out if required. – The mains connection cable may only be replaced by an original Miele spare part or an apppropriate cable with wire end ferrule. – For technical data see data plate or...
Electrical connection Removing the plinth panel Equipotential bonding connection The electrical connection point is There is a screw connection point located behind the front plinth panel in marked with the earth symbol (8) at the the middle. back of the machine, to which additional equipotential bonding can be Disconnect the machine from the connected.
30 and 1000kPa (0.3 and 10bar). If Providing your dishwasher has been the water pressure is lower than this, installed correctly, the Miele waterproof Inlet the fault message will appear in anti-leak system will protect you from the display (see "Problem solving...
Plumbing To avoid any damage to the machine, the dishwasher must only be connected to a fully vented plumbing system. The inlet hose must not be shortened or damaged in any way as it contains electrical components (see illustration).
To vent it: If separate drainage is not available ^ Open the dishwasher door fully. contact Miele for professional advice. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Noise emission values Sound level in LwA 49 dB (A) Noise level in LpA 38 dB (A) Test certificates awarded EMC, VDE, radio and television suppressed ! mark 2006/42/EC Machine guidelines Manufacturer's address Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany...
Settings menu Settings menu for changing Language standard settings The display can be set to appear in one of several different languages. To open the Settings menu You can select one of the languages ^ Switch the dishwasher off with the - Language displayed via the button, if it is switched on.
Settings menu Water hardness °d Value Your dishwasher is fitted with a water German mmol/l °f displayed softener which you need to programme scale to the water hardness level in your area. – Your local water authority will be able to advise you of the water hardness level in your area.
Settings menu Rinse aid Buzzer You can adjust the rinse aid dosage for When the buzzer is activated, an best results. The rinse aid dosage can audible tone sounds at the end of a be set from approx. 0-6 ml. The factory programme and when there is a fault.
Settings menu AutoOpen Optimise standby In order to help the drying process, the To save energy, the dishwasher will door will automatically open a little at switch to Standby mode a few minutes the end of the programme (except after the last time a button has been Pre-wash, Short and Beer glasses).
Settings menu Check filters You can switch off the reminders to You can adjust the interval at which the replenish salt and rinse aid so that reminder to check the filters appears. the dishwasher will go into Standby You can set an interval of between 30 despite a lack of salt or rinse aid.
Settings menu Detergent amount Venting the dispensing system The dispensing system will only This function will only be visible if the dispense reliably when there is no air in External dispenser option has been the system. activated. The dispensing system must be vented For dispensing liquid detergent via the G 60 Semi Dos Module you can set the –...
Settings menu Final rinse temp. To facilitate drying the temperature of the final rinse can be increased in individual programmes. The function is not available for every programme (see the Programme chart). ^ Select the setting you want, and confirm your selection with the middle button.
Settings menu Showroom prog. Factory settings If you have altered any settings from This setting is intended for dealers the factory default, you can reset them only. back to the factory default settings. You cannot use this function to reset either The dishwasher is fitted with the External dispensing option if this demonstration programmes for...
Alteration rights reserved / Publication date 22.06.2012 M.-Nr. 09 402 650 / 00...