Parts List Description Number Q'ty Unit Console & Screw A, A-1 Front handlebar Foam grip Hand pulse End cap for front handlebar Screw M4x20L for hand pulse Semicircle washer 1.5T for hand pulse Wire for hand pulse Upper handlebar (Left) End cap for upper handlebar Foam grip for upper handlebar Upper handlebar (Right)
Page 8
Cross disc F-16 Flat washerφ5xφ16x1t F-17 Nut M10xP1.25x10T for Cross disc F-18 Front cover (Right ) F-19 Chain cover (Right ) F-20 Screw M5x16L F-21 Round disc F-22 Chain cover (Left) F-23 Self tapping screw M4x50L F-24 Front cover (Left) F-25 Cover for the handlebar post F-26...
Page 9
Assembly Stage #1 Attach the front stabilizer (J-4) to the main frame (F) using two flat washer (L-23) and allen bolt (L-11). Attach the rear stabilizer (J) to the main frame (F) using two flat washer (L-23) and allen bolt (L-11) .
Page 10
Assembly Stage #3 L- 22: flat washer *1T (4) L- 15: Carriage Bolt M6*P1.0*50L (8) L- 14: Spr i ng W asher φ ( 8) L- 13: Knob ( f oot pedal ) M 6*P1. 0 ( 8) L- 12: Pi vot Tube 7* 12*30( 4) 1.
Page 11
Assembly Stage #4 Please remove four sets of the allen bolt (F-3) and flat washer (F-2) from the main frame (pt.F) 2. Take the handlebar post (D) and pass it through the handlebar post cover (F-26). 3. Hold the handlebar post (D) and connect the lower computer cable (F-1) and the upper computer cable (pt.
Page 12
Assembly Stage #5 1. Take the axle (D-6) and pass it through the handlebar post (D). 2. Pass the axle through the wave washer (L-9) and the lower handlebar (E-R/L) ,and then fix with the flat washers (L-7) and gasket (L-6) and allen bolt (L-5) in each side. 3.
Page 13
Assembly Stage #6 1. Please remove four sets of the from the screw (K-1) pedal arm (K-L/R). 2. Assemble the front cover L/R (K-2,K-4) for the pedal arm (K-L/R) by screw (K-1) in each side.
Page 14
Assembly Stage #7 Pass the hand-pulse wire (pt.B-6) through the handlebar post (D-7) hole. Attach the front handlebar (B) to the handlebar post (D) using the clamp cover (L-18), and then fix with two flat washers (L-19), two spring washers (L-20), two fixing bolt (L-21). Assembly Stage #8 1.
Page 15
Assembly Stage #9 1. Please remove from the handlebar post (D) screw (D-2) 2. Assemble the console holder cover (D-3,D-4) for the handlebar post (D) by the screw (D-2) and self tapping screw (L-1)
Page 16
Assembly Stage #10 1. Assemble the R/L upper handlebar (C,C-4) for the lower handlebar (E-R/L) by carriage bolts (L-2) with nut (L-3) and semi-circle washer (L-4).
Page 17
NSTRUCTIONAL MANUAL FOR CASALL XT12 CONSOLE DISPLAY FUNCTIONS : ITEM DESCRIPTION TIME .Range 0:00 ~ 99:59 .Workout time elapsed. SPEED .Range 0.0 ~ 99.9 km/hr .Current speed during workout. DISTANCE .Range 0.0 ~ 99.9 KM .Workout distance travelled. CALORIES .Burned calories during workout.
KEY FUNCTION: ITEM DESCRIPTION Increase resistance level ‧ ‧ Setting selection. Decrease resistance level ‧ Down ‧ Setting selection. ‧ Confirm setting or selection. Mode ‧ Hold on pressing for 2 seconds, computer will reboot and start from user setting. Reset ‧...
Page 19
Program Mode Choose a preset workout program. 1. Press UP or DOWN to select workout program, choose the Program and press Mode to enter. (Total Program = 12) 2. Press UP or DOWN to set target TIME. 3. Press START/STOP key to start workout. Press UP or DOWN to adjust resistance level. 4.
Page 20
WATT Mode Monitor the energy output of workout 1. Press UP or DOWN to select workout program, choose WATT and press Mode to enter. 2. Press UP or DOWN to set target WATT value (default: 120). 3. Press UP or DOWN to preset TIME. 4.
*Please see reference Body Fat chart below to determine body fat range. *Please see reference BMI chart below to determine the BMI range. <REFERENCE> B.M.I. (Body mass index) integrated B.M.I SCALE LOW/MED MEDIUM MED/HIGH RANGE <20 20-24 24.1-26.5 >26.5 BODY FAT: RANGE LOW/MED MEDIUM...