Advertisement
Quick Links
Advertisement
Related Manuals for Casall INF 2.0 PLUS
Summary of Contents for Casall INF 2.0 PLUS
- Page 1 Casall INF 2.0 PLUS CROSSTRAINER 93017...
- Page 2 Important: Please locate your serial number and record in the box below for service support purposes. Serial number here: ...
- Page 3 93017 INF2.0 plus P-13 P-12 Screw Allen Bolt M7*P1.0*30L (2) M3x14L (2) Nut M8 (2) Wave washer Ø20xØ30x0.3t Flat washer Ø8xØ25x2t (2) P-11 Flat washer Spring washer Ø7x1t (2) Ø7x2t (2) Allen bolt M8x12L (8) Steel washer（2） P-15 P-14 Metal cover (1) Allen bolt M8x16L (4) P-10 Flat Washer Ø8xØ16x1t (4)
- Page 4 93017 INF2.0 plus P-16 Box Spanner (1) Allen Key(2) P-17 P-19 Knob M6*P1.0 (4) P-18 Spring washer Ø6 (4) Carrage bolt M6*P1.0*40L (4) Bushing (4)
-
Page 5: Exploded Diagram
EXPLODED DIAGRAM... -
Page 6: Parts List
PARTS LIST Item spec. Q'ty A , A-1 Computer & Screw for computer 1SET Front handlebar Foam grip for front handlebar 2PCS End cap for foam grip φ7/8" 2PCS Hand pulse WP1007-33B 1SET Screw M3x20L 2 PCS Wire for hand pulse 1 PC Upper handlebar ( L) 1SET... - Page 7 L-1~L-11 Idler wheel set 1SET Front cover for computer Rear cover for computer Bottle holder Front cover (Left) for pedal post 2PCS Front cover (Right) for pedal post 2PCS Pedal (Left) M-7,M8 Left rear cover (upper/down) for pedal post 1SET Pedal (Right) M-10,M-11 Right rear cover (upper/down) for pedal post 1SET...
-
Page 8: Assembly Steps
ASSEMBLY STEPS STEP 1 Attach the Front Stabilizer (J-1) to the Main Frame (F-1) using two Allen bolt (P-7) Attach the Rear Stabilizer (K-1) to the Main Frame (F-1) using two Allen bolt (P-7). M8*16L STEP 2 1. Please remove four sets of the M8x16 Allen bolt (D-5) and Flat Washer (D-6)from the Main Frame (F-1) 2. - Page 9 STEP 3 1. Attach the Front handlebar (B-1) to the Handlebar post (D-1) using the clamp cover (P-3), and then fix with two Flat Washers (P-2), two Spring Washers (P-4), two Fixing Bolt (P-1). 2. Pass the hand-pulse wire (B-6) through the hole. 3.
- Page 10 Fix the two Lower handlebar (E-1) to the Handlebar Post (D-1) with one Axle (M-19), STEP 5 two sets of Wave washer (P-13), Flat washers (P-12) and Gasket (P-11) and Allen bolt (P-10). Pay attention : Please use two allen key tools to fix bolt (P-10) on both side at the same time. Steel washer Ø20xØ30x0.3t Ø8xØ25x2t...
- Page 11 STEP 7 1. Remove the pre-installed screws (I-2) on the Pedal post first. 2. Attach the Lower handlebar (E-1 R/L) to the left and right pedal post (I-1), and then close the cover (M-4 & M-5) using screws (P-5 & I-2). 3.
- Page 12 STEP 9 Connect the adaptor (N) to the DC hole (located on the back of the chain cover). Fit hi way App INSTRUCTION MANUAL 比 例 25. 400 System plug connection socket Hand pulse socket...
- Page 13 DISPLAY FUNCTIONS ITEM DESCRIPTION Count up - No preset target, Time will count up from 00:00 to maximum 99:59 with TIME each increment is 1 minute. Count down - If training with preset Time, Time will count down from preset to 00:00. Each preset increment or decrement is 1 minute between 00:00 to 99:00.
-
Page 14: Workout Selection
OPERATION: POWER ON Plug in power supply, computer will power on and display all segments on LCD for 2 seconds (Drawing 1). Drawing 1 WORKOUT SELECTION Use UP or DOWN (Encoder) to select workout Manual (Drawing 2) Beginner(Drawing 3) Advance (Drawing 4) ... - Page 15 Drawing 8 Drawing 9 Drawing 10 Drawing 11 Drawing 12 Beginner Mode 1. Use UP or DOWN (Encoder) to select workout program, choose Beginner mode and press MODE / ENTER to get into. 2. Use UP or DOWN (Encoder) to select Beginner program 1~4 (Drawing 13) and press MODE / ENTER to get into.
- Page 16 Drawing 14 Sporty Mode 1. Use UP or DOWN (Encoder) to select workout program, choose Sporty mode and press MODE / ENTER to get into. 2. Use UP or DOWN (Encoder) to select Sporty program 1~4 (Drawing 15) and press MODE / ENTER to get into.
- Page 17 Drawing 18 Measuring your pulse with the hand sensors The hand sensor are not medical products, but rather exercising tools designed for the approxl-mate measurement and displaying of the pulse rate when exercising with the exercise bike. You can measure your pulse with the two hand sensor on the handle.
- Page 18 NOTE: 1. Once console is connected to tablet via Bluetooth, the console will power off. 2. Please exit Fit Hi Way app and turn off the Bluetooth from the smart device, then the console will power on again. 3. If console operation or display abnormally, please Power-off and restart it. The manual will be updated from time to time, the consumer can get the newest version by scanning the QR code or link to the website as below.