Page 5
PARTS LIST Description Specifications Q'TY A-1,A-2 COMPUTER & SCREW 1SET HANDLEBAR 1 PC CAP FOR HANDBLEBAR 2 PC FOAM GRIP 2 PC ELBOW HOLDER (R) HAND PULSE SET W/WIRE 1SET ELBOW HOLDER (L) HANDLEBAR POST 1 PC COMPUTER CABLE (UPPER) 1 PC BOTTLE HOLDER 1 PC...
Page 6
D-26 FLAT WASHER φ15xφ16x1t 8 PC D-27 CROSS DISC (L) D-28 CAP FOR CHAIN COVER SCREW HOLES OVAL 4 PC D-29 CAP FOR CHAIN COVER SCREW HOLES ROUND 5 PC D-30 COVER FOR HANDLEBAR POST 1 PC D-31 SPRING RING 2 PC D-32 BUSHING...
Step 1 Foot Tube Assembly Attach the Front Stabilizer (F-1) to the Main Frame (D-1) using two M8x16 Allen bolt (J-1) Attach the Rear Stabilizer (F-6) to the Main Frame (D-1) using two M8x16 Allen bolt (J-1). M8*16L Step 2 Pedal Assembly 1.
Page 8
Step 3 --Seat Tube Assembly 1. Assemble the seat (G-7) to the Slider. The Slider can be adjusted in different angles. Tighten the two Nuts under the Seat using a screwdriver. In addition, the Slider can be adjusted in horizontal level by loosing the Knob.
Page 9
Step 4-Handlebar post Assembly 1. Please remove the M8x16 Allen bolt (D-3) and flat washers (D-4) from the main frame (D-1) 2. Take the Handlebar post cover (D-30) and pass it through Handlebar post (C-1) 3. Hold the Handlebar post (C-1) and connect the Lower computer cable (D-2) to the Upper computer cable (pt.
Page 10
Step 5- Handlebar and Computer Assembly 1. Attach the Handlebar (B) to the Handlebar post (C-1) using the clamp (J-8). Fix firmly with one Flat washers (J-3), one Spring washer (J-4) and one Fixing bolt (J-2). 2. Pass the hand-pulse wire (B-4) through the hole. 3.
Page 11
Step 6- R/L Cover and Bottle holder Assembly 1. Attach the Rear cover (C-5) using two of M3x14L Screws (J-7) and one of M5xP0.8x14L Screws (C-4) . 2. Attach the Front cover (pt.C-6) using M5x14L Screws (C-4) the Handlebar T-Knob (J-6) using one set of Flat Washer (J-3), Spring Washer (J-4) and one Bushing (J-5).
Page 12
Fit hi way App INSTRUCTION MANUAL 比例 25.400 System plug connection socket Hand pulse socket...
Page 13
DISPLAY FUNCTIONS ITEM DESCRIPTION Count up - No preset target, Time will count up from 00:00 to maximum 99:59 with TIME each increment is 1 minute. Count down - If training with preset Time, Time will count down from preset to 00:00. Each preset increment or decrement is 1 minute between 00:00 to 99:00.
OPERATION: POWER ON Plug in power supply, computer will power on and display all segments on LCD for 2 seconds (Drawing 1). Drawing 1 WORKOUT SELECTION Use UP or DOWN (Encoder) to select workout Manual (Drawing 2) Beginner(Drawing 3) Advance (Drawing 4) ...
Page 15
Drawing 8 Drawing 9 Drawing 10 Drawing 11 Drawing 12 Beginner Mode 1. Use UP or DOWN (Encoder) to select workout program, choose Beginner mode and press MODE / ENTER to get into. 2. Use UP or DOWN (Encoder) to select Beginner program 1~4 (Drawing 13) and press MODE / ENTER to get into.
Page 16
Drawing 14 Sporty Mode 1. Use UP or DOWN (Encoder) to select workout program, choose Sporty mode and press MODE / ENTER to get into. 2. Use UP or DOWN (Encoder) to select Sporty program 1~4 (Drawing 15) and press MODE / ENTER to get into.
Page 17
Drawing 18 Measuring your pulse with the hand sensors The hand sensor are not medical products, but rather exercising tools designed for the approxl-mate measurement and displaying of the pulse rate when exercising with the exercise bike. You can measure your pulse with the two hand sensor on the handle.
Page 18
NOTE: 1. Once console is connected to tablet via Bluetooth, the console will power off. 2. Please exit Fit Hi Way app and turn off the Bluetooth from the smart device, then the console will power on again. 3. If console operation or display abnormally, please Power-off and restart it. The manual will be updated from time to time, the consumer can get the newest version by scanning the QR code or link to the website as below.