Selecting The Digital Input Terminals-Digital In - JVC RX-5032VSL Instructions For Use Manual

Basic Settings
7 Speaker distance—DISTANCE UNIT,
FRNT (Front) DISTANCE, CNTR (Center) DISTANCE,
SURR (Surround) DISTANCE
Select the unit to measure the distance between your listening
position and speakers—"METER" or "FEET."
After selecting the measuring unit, select the appropriate
speaker distance for each speaker within the range of "0.3m"
("1FT") to "9.0m" ("30FT") by 0.3 m (1 foot) step.
Example:In this case, set "FRNT DISTANCE" to "3.0m" ("10FT"),
"CNTR DISTANCE" to "2.7m" ("9FT"), and "SURR
DISTANCE" to "2.4m" ("8FT").
• "METER" for the unit and "3.0m" ("10FT") for all speakers are
the initial settings.
Note:
If you have selected "NONE" for the center and surround speakers
setting, you cannot set the speaker distance for the center and
surround speakers.
7 Crossover frequency—CROSSOVER
Small speakers cannot reproduce the bass sounds efficiently.
If you use a small speaker in any position, this receiver
automatically reallocates the bass sound elements assigned
to the small speaker to other large speakers.
To use this function properly, set the crossover frequency
according to the table below:
Crossover frequency
80HZ
100HZ
120HZ
150HZ
200HZ
• If you have selected "LARGE" for all speakers, this function
will not take effect ("CROSS OFF" appears).
L R
C
3.0 m
(10 feet)
2.7 m
(9 feet)
2.4 m
(8 feet)
2.1 m
(7 feet)
LS RS
Size of cone speaker unit built in the
small speaker
about 12 cm
about 10 cm (initial setting)
about 8 cm
about 6 cm
less than 5 cm
7 Low Frequency Effect attenuator—LFE ATTENUATE
If the bass sound is distorted while playing back software
encoded with Dolby Digital or DTS Digital Surround, select
"–10dB" to activate the Low Frequency Effect attenuator.
• This function takes effect only when the LFE signals come
in.
0dB Normally select this (initial setting).
–10dB Select this when the bass sound is distorted.
7 Dynamic range compression—D_COMPRESSION
You can compress the dynamic range (difference between
maximum sound and minimum sound) of the reproduced
sound. This is useful when using surround sound at night.
• This function takes effect only when playing back a source
using Dolby Digital.
MID Select this when you want to reduce the dynamic
range a little (initial setting).
MAX Select this when you want to apply the
compression effect fully. (Useful at night.)
OFF Select this when you want to enjoy surround sound
with its full dynamic range. (No effect applied.)
Selecting the Digital Input Terminals—
DIGITAL IN
When you use the digital input terminals, register which
components are connected to which terminals (DIGITAL 1/2)
so that the correct source name will appear when you select
the digital source.
Select the appropriate option from the following:
O
1 DVD 2 CD 1 DVD 2 TV
O
1 CD 2 DVD 1 CD 2 TV
O
1 TV 2 DVD 1 TV 2 CD
O
1 CDR 2 CD
1 CDR 2 DVD
(back to the beginning)
Note:
When shipped from the factory, the DIGITAL IN terminals have been
set for use with the following components:
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
O O
1 DVD 2 CDR
O
O
1 CD 2 CDR
O O
1 TV 2 CDR
O
O
1 CDR 2 TV
14