Lincoln Electric POWERWAVE 655/R Service Manual page 138

L11396-2
ENGINEERING CONTROLLED
MANUFACTURER:
4.50 ±.04
Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty.
vided for reference only. Lincoln Electric discourages board level troubleshooting and repair since it may compromise the quality of the design and may result in danger to the Machine Operator or Technician. Improper PC board repairs could result in damage to the
machine.
REVISED MAKE SPECIFICATION
CHANGE DETAIL:
No
P.C. BOARD BLANK INFORMATION
BUY COMPLETE AS L11396-B
( 2 LAYER BOARD PER E3281)
(MAKES 8 B OARDS PE R PANEL, SEE ELECTRON IC FILE
FOR ADDITIONAL IN FORMATION)
N.D.
N.A.
XXXXXXXX XXXXXXX
INPUT
J61
D1
R22 TP4
D2
TP3
R24 OCI1
R11
R25
R12
R23
TP2 R13
R21
R14
1 R20
R15
R19
XXX TP1 R16
R18
X R17 X
X X
R7
CR2
X X
X R6 X
X X
R9
R8
X X
X
X X
R3
X
X X
R1
XXX
X
X X
N.B.
R2
R10
X
X X
L11396-2
0
N.D.
N.D.
0
MAKE PER E1911-ROHS
ENCAPSULATE WITH E1844
TEST PER E3647-I
SCHEMATIC REFERENCE: M19528-2B0
3
N.D.
J60
CR1
X
X
X
X
6.00 ±.04
MAN U FACT U RED AS:
L11396-2B0
I DEN T IFICA T I ON CODE
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OWNED BY LINCOLN GLOBAL, INC. AND MAY NOT BE DUPLICATED, COMMUNICATED
PROPRIETARY & CONFIDENTIAL:
TO OTHER PARTIES OR USED FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF LINCOLN GLOBAL, INC.
UNLESS OTHERWISE SPECIFIED TOLERANCE
REFERENCE:
DESIGN INFORMATION
MANUFACTURING TOLERANCE PER E2056
ON 2 PLACE DECIMALS IS ± .02 L11396-1
FEI
DRAWN BY:
ON 3 PLACE DECIMALS IS ± .002
ON ALL ANGLES IS ± .5 OF A DEGREE
SCALE:
MATERIAL TOLERANCE (" ") TO AGREE t ENGINEER:
WITH PUBLISHED STANDARDS.
- 1:1
APPROVED:
DO NOT SCALE THIS DRAWING
REFERENCES QTY PART NO. DESCRIPTION
C1 1 S16668-5 .022/50
CR1, CR2 2 S14293-18 DPST RELAY
D1, D3 2 T12199-1 1N4004
D2 1 T12705-58 DIODE,1.0A,1500V
N.C. J60 1 S24020-8 HEADER,VERTICAL
N.C. J61 1 S24020-10 HEADER,VERTICAL
OCI1 1 S15000-22 OPTO ISOLATOR
R1, R2, R3, R6, R7, R8, R9, R10 8 S24376-3 100/1OW
R4 1 S19400-2673 267K 1/4W
R5 1 S19400-4750 475 1/4W
R11, R12, R13, R14, R15, R16, 15 S19400-3011 3.01K 1/4W
R17, R18, R19, R20, R21, R22,
R23, R24, R25
TP1, TP2, TP3, TP4 4 T13640-23 MOV,250J,660V
ITEM REQ'D PART NO. IDENTIFICATION
1 1 SEE BLANK INFO. P.C. BD. BLANK
2 1.0 OZ. E2861 SEALANT
3 2 S14020-7 PLASTIC EXPANSION NUT
CAPACITORS = MFD / VOLTS
RESISTORS = OHMS/WATTS
N.A. THIS AREA TO BE COVERED ON BOTH SIDES OF BOARD WITH ITEM 2 PRIOR TO
ENCAPSULATION. MATERIAL MUST BE APPLIED THRU SLOTS FROM BOTTOM
SIDE TO COMPLETELY FILL TO UNDERSIDE OF DEVICE ON COMPONENT SIDE.
N.B. P.C. BOARD HOLES TO BE FREE OF ENCAPSULATION MATERIAL.
N.C. DO NOT COAT WITH ENCAPSULATION MATERIAL.
N.D. APPLY ITEM 2 AS SHOWN, ALL EXPOSED LEADS MUST BE COVERED. MATERIAL
MUST BE APPLIED PRIOR TO ENCAPSULATION.
N.E. APPLY ITEM 2 ON NON-COMPONENT SIDE OF BOARD PRIOR TO
ENCAPSULATION. ALL EXPOSED PINS MUST BE COVERED.
ALL C OMPONE NT S AND MATE RI ALS U SE D IN TH IS
ASSEM BL Y ARE TO B E RoH S C OMPLIA NT PE R E4253.
INVERTER WELDERS
EQUIPMENT TYPE:
PAGE ___ OF ___
DOCUMENT
INPUT P.C. BOARD ASSEMBLY
SUBJECT:
NUMBER:
L11396-2
MATERIAL APPROVAL PROJECT
UF CRM34409
3/16/2007
DISPOSITION: DATE: NUMBER:
This information is pro-
1 1
DOCUMENT
REVISION:
B
STRP