Table of Contents
Advertisement
WALRB4P manual booklet
PROGRAMMING A MASTER POWER MACRO (continued)
Clearing The Master Power Macro
1.
Press and hold
then release
SET
2.
Enter
-
-
. The
9
9
5
once.
3.
Press and hold
. The Master Power Macro is now cleared.
SET
RE-ASSIGNING DEVICE KEYS
The One For All 4 Device Universal Remote Control can be set to control a
second PVR,VCR, or DVD player. For example, to control a TV, a cable box,
and two DVD players , re-assign the unused
DVD player as follows:
1.
On the remote control, press and hold
(red light) blinks twice, then release
2.
Enter
-
-
. The
9
9
2
3.
Press
once.
DVD
4.
Press
once. The
VCR/PVR
key is now ready to be set up to control your second DVD
player. See Programming Device Control on page 8.
To re-assign a second VCR or PVR (or DVR) to the unused
steps 1 through 4 . However, in step 3 substitute
4 substitute
for
. Now the
DVD
VCR/PVR
your second VCR or PVR (or DVR). See Programming Device Control on page
8.
NOTE: Only one device can be assigned to an unused device key at a time.
USING CHANNEL SCAN
In the
or
mode, use the
CBL/SAT
TV
channels. Or, if programmed, use the
channels to view a desired channel (see Programming Favorite Channel Scan
on next page. )
1.
Press
or
CBL/SAT
5/2/06
3:16 PM
Page 11
until the
(red light) blinks twice,
SET
LED
.
will blink twice. Then press
LED
POWER
until the
blinks twice, then release
SET
LED
key to operate the second
VCR/PVR
until the
SET
LED
.
SET
will blink twice.
LED
will blink twice. The
LED
VCR/PVR
key, repeat
DVD
for
, and in step
VCR/PVR
DVD
key will be ready to be set up as
DVD
key to start a 3-second scan of all
FAV
key to scan only your favorite
FAV
once.
TV
11
2.
Press
once.
FAV
• If Favorite Channel Scan has been set up,scanning of
favorite channels will start with up to 100 channel changes
or until stopped by pressing any key.
• If Favorite Channel Scan has not been set up, scanning
will start with the current channel, and continue up to
100 channel changes or until stopped by pressing any key.
3.
To stop scanning channels at any time, press any key
once.
PROGRAMMING FAVORITE CHANNEL SCAN
In the
or
mode, you can store a list of up to 10 favorite channels,
CBL/SAT
TV
in any order, that will be immediately scanned when
Using Channel Scan on the previous page).
NOTE: Favorite channels can only be programmed for one mode.After programming, if FAV
is pressed while in another mode, the remote control will start scanning all channels instead
(if applicable to the selected device).
1.
On the remote control, press
2.
Press and hold
until the
SET
then release
.
SET
3.
Enter
-
-
. The
9
9
6
LED
4.
Use the keypad to enter a favorite channel number (e.g.,
). Then press
031
SET
NOTE: If the original remote control required pressing an Enter key
to change the channel, also press the ENTER key after the channel
number (e.g., 0 - 3 - 1 - ENTER). On some satellite receivers and cable
boxes, you may need to press the SELECT (OK) key instead of ENTER.
5.
If desired, repeat step 4 for each channel to be stored, up
to a total of 10 channels.
NOTE: If you try entering more than 10 channels, the remote control
will automatically exit programming. To change your favorite chan-
nel list at this point, you will first need to delete the existing list by
performing the steps in "Clearing Custom Programming"on page 14.
Then, perform the instructions in this section once again.
6.
To exit programming with less than 10 favorite channels
stored, press and hold
Otherwise, the remote control will automatically exit the
program after 10 channels have been stored.
12
is pressed (see
FAV
or
once.
CBL/SAT
TV
(red light) blinks twice,
LED
will blink twice.
once.
until the
blinks twice.
SET
LED
Hide quick links:
Advertisement
Table of Contents
