Induction Dynamics S2.c Owner's Manual

Corner speaker

Advertisement

Quick Links

S2.c
Corner Speaker

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S2.c and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Induction Dynamics S2.c

  • Page 1 S2.c Corner Speaker...
  • Page 2: Table Of Contents

    Introduction General Information Check Speaker and Parts General Care of Your Loudspeaker and Amplifier Bass and Loudness Contour Controls S2.c Location Stands Speaker Wire Speaker Information S4X Crossover Wide Angle Phase Alignment Multi-Channel (Home Theater) Installation Speaker Placement and Mounting S2.c Speaker Connection S2.c Specifications Warranty Contacts...
  • Page 3: Introduction

    Because of S4X technology, any of Induction Dynamics’ speakers can be used to build a custom home theater system. Your S2.c can be combined with any of our main, center, and surround speakers, be they in-wall, on-wall, or free-standing.
  • Page 4: General Information

    “boomy”, obscure higher frequencies, and possibly cause damage. S2.c Location S2.c speakers are normally mounted on-wall, but may also be used as bookshelf speakers. The height of the S2.cs should be determined by locating the tweeter at ear level. The tweeter reproduces high-frequency audio, which our ears perceive as most directional, so we are most attuned to their level and placement.
  • Page 5: Stands

    Stands A speaker stand is not included with the S2.c, but is available for purchase through your authorized Induction Dynamics dealer. The companion stand for the S2.c is the ST1.S2.c. Speaker Wire Use approved wire designed for in-wall or exposed use, as appropriate for your installation. For the S2.c, we recommend using high-quality speaker wire that is 12 gauge or lower, with easily visible polarity coding to make your connections. The following chart identifies...
  • Page 6: Speaker Information

    Above: The S4X crossover routes audio signal to their intended drivers at specific frequen- cies (the S2.c utilizes a single crossover at 2500 Hz). Because the S4X produces such a steep crossover slope, Induction Dynamics is able to use the best possible drivers for each frequency range. Subwoofer crossover points are generally selectable through your sub- woofer amplifier. Induction Dynamics recommends a subwoofer crossover point between 50 - 60 Hz.
  • Page 7: Wide Angle Phase Alignment

    Induction Dynamics® eliminates phase differences with respect to height through our Wide Angle™ phase alignment technology. Because our patented circuitry provides additional variables that can help control phase, Wide Angle finds the one optimization solution that produces a flat frequency response along the vertical axis, when the microphone (or listener’s...
  • Page 8: Multi-Channel (Home Theater) Installation

    4. If you are running wire into the wall, use one of the oval slots in the side of the bracket to run wire through. 5. Slide the S2.c, with hex head bolts sticking out from the back, into the bolt slots, making sure both bolts are in their slot.
  • Page 9: S2.C Specifications

    S2.c Specifications 2-way freestanding loudspeaker. Type: Exclusive patented S4X Driver Control Technology. Crossover: Crossover Frequencies: 2,500 Hz Nominal Impedance: 4 Ohms 55-22,000 Hz Frequency Response: 88 dB Sensitivity (2.83 V @ 1M): 85 dB SPL (1 W / 1 M): 175 W...
  • Page 10: Warranty

    The warranty is void if the S2.c is serviced or altered by anyone other than Induction Dynamics, Inc. the sole remedy for breach of this warranty shall be repair or replace- ment.
  • Page 11: Contacts

    Contacts Manufacturer Information If you have any questions, contact Induction Dynamics by phone at 855-663-5600, 8:00 a.m.- 5:00 p.m. CST, fax at 913-663-3200, email at sales@inductiondynamics.com, or write to: Induction Dynamics Customer Service Department 8005 W. 110th St., Suite 208...
  • Page 12 To simplify your record keeping, please glue, staple, or tape your receipt to this page.
  • Page 13 Audio Perfection Realized ™...
  • Page 14 8005 W. 110th Street, Suite 208 Overland Park, KS 66210 Tel: (855) 663-5600 Fax: (913) 663-3200 www.inductiondynamics.com © Induction Dynamics®, August 2013 ™...

Table of Contents