Note For Schematic Diagram; Note For Parts List - Denon AVR-3311CI Service Manual

NOTE FOR SCHEMATIC DIAGRAM

WARNING:
Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture
CAUTION:
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the
leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
WARNING:
DO NOT return the unit to the customer until the problem is located and corrected.
NOTICE:

NOTE FOR PARTS LIST

ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM
ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL
INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
NOTE FOR PARTS LIST
1. Parts for which "nsp" is indicated on this table cannot be supplied.
2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
3. Ordering part without stating its part number can not be supplied.
4. Part indicated with the mark " " is not illustrated in the exploded view.
5.
Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
6. Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
Resistors
Ex.: RN 14K
Type Shape
and per-
formance
RD : Carbon 2B : 1/8 W
RC : Composition 2E : 1/4 W
RS : Metal oxide film 2H : 1/2 W
RW: winding 3A : 1 W
RN : Metal film 3D : 2 W
RK : Metal mixture 3F : 3 W
3H : 5 W
Resistance
1 8 2 1800ohm=1.8kohm
Indicates number of zeros after effective number.
2-digit effective number.
1 R 2 1.2ohm
1-digit effective number.
2-digit effective number, decimal point indicated by R.
: Units: ohm
Capacitors
Ex.:
CE 04W
Type Shape
and per-
formance
CE : Aluminum foil
electrolytic
CA : Aluminium solid
electrolytic
CS : Tantalum electrolytic
CQ : Film
CK : Ceramic
CC : Ceramic
CP : Oil
CM: Mica
CF : Metallized
CH : Metallized
Capacity (electrolyte only)
2 2 2 2200 F
Indicates number of zeros after effective number.
2-digit effective number.
Units: F.
Capacity (except electrolyte)
2 2 2 2200pF=0.0022 F
Indicates number of zeros after efective number. (More than 2)
2-digit effective number.
Units:pF
When the dielectric strength is indicated in AC,"AC" is included after the dieelectric strength value.
2E 182 G
Power Resist- Allowable
ance error
F : 1% P : Pulse-resistant type
G : 2% NL : Low noise type
J : 5% NB : Non-burning type
K : 10% FR : Fuse-resistor
M : 20% F : Lead wire forming
1H 3R2 M
Dielectric Capacity Allowable
strength error
0J : 6.3 V F : 1%
1A : 10 V G : 2%
1C : 16 V J : 5%
1E : 25 V K : 10%
1V : 35 V M : 20%
1H : 50 V
Z : 80%
2A : 100 V
: - 20%
2B : 125 V
P : +100%
2C : 160 V
C : 0.25pF
2D : 200 V
D : 0.5pF
2E : 250 V = : Others
2H : 500 V
2J : 630 V
FR
Others
BP
Others
HS : High stability type
BP : Non-polar type
HR : Ripple-resistant type
DL : For change and discharge
HF : For assuring high requency
U : UL part
C : CSA part
W : UL-CSA part
F : Lead wire forming
2 R 2
1-digit effective number.
2-digit effective number, decimal point indicated by R
Units: F.
2 2 1
Indicates number of zeros after effective numver. (0 or 1)
2-digit effective number.
Units:pF
3
r.
2.2 F
220pF