Rinsing; Descaling; Install Filter; Replacing The Limescale Filter (If Installed) - DeLonghi ETAM29.66X Instructions For Use Manual

Rinsing

Use this function to deliver hot water from the coffee spout (A8)
and from the hot water spout (C3), if inserted, to clean and heat
the appliance's internal circuit. Place a container with a mini-
mum capacity of 100ml under the coffee and hot water spout.
To enable the function, proceed as follows:
1. Press the icon (B2) to enter the menu;
2. Press or (fig. 5) until "Rinsing" is displayed;
3. Press the icon (fig.6), "Confirm?" is displayed;
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. Press the icon: after a few seconds, hot water is deliv-
ered first from the coffee spout and then from the hot water
spout (if inserted) which cleans and heats the appliance' s
internal circuit.
Please note!
• To stop delivery at any time, press any icon.
• If the appliance is not used for more than 3-4 days, we strong-
ly recommend, when switching on the appliance, performing
2/3 rinses before using it.

Descaling

For instructions on descaling, see page 18.

Install filter

For Instruction for use on how to install the filter, see the section
"Water softener filter" (page 20).

Replacing the limescale filter (if installed)

For Instruction for use on how to replace the filter, see the sec-
tion "Replacing the filter" (page 20).

Adjust time

To adjust the time on the display, proceed as follows:
1. Press the icon (B2) to enter the menu;
2. Press or (fig. 5) until "Adjust time" is displayed;
3. Press the icon (fig. 3). The hours flash on the display;
4. Press or to change the hour;
5. Press the icon to confirm. The minutes flash;
6. Press or to change the minutes;
7. Press the icon to confirm.
This sets the time. Press the icon to exit the menu.

Auto-start

You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the icon (B2) to enter the menu;
2. Press or (fig. 5) until "Auto-start" is displayed;
3. Press the button (fig. 3). "Enable?" is displayed;
4. Press the icon to confirm;
5. Press or to choose the hour;
6. Press the icon to confirm;
7. Press or to change the minutes;
8. Press the icon to confirm;
9. Press the icon to exit the menu.
Once the time has been confirmed, activation of auto-start is
indicated by the symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the icon. "Disable?" is displayed;
3. Press the icon to confirm.
The symbol is no longer displayed.

Auto-off (standby)

Auto-off can be set so that the appliance goes off after 15 or
30 minutes, or 1, 2 or 3 hours. To programme Auto-off, proceed
as follows:
1. Press the (B2) icon (B2) to enter the menu;
2. Press or (fig. 5) until "Auto-off" is displayed;
3. Press the icon (fig. 6);
4. Press or until the required operating time (15
or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the icon to confirm;
6. Press the icon to exit the menu.
Auto-off is programmed.

Energy saving

Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the icon (B2) to enter the menu;
2. Press or (fig. 5) until "Energy Saving" is
displayed;
11